Related Manuals for Vector Welding London2400
Summary of Contents for Vector Welding London2400
- Page 1 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS London2400 Welding Machine Register now and benefit! Jetzt Registrieren und Profitieren! www.smart-iwm.com...
- Page 2 • Observe accident prevention regulations! • Observe all local regulations! VECTOR welding equipment can be used on nearly all weld able metals. It is particularly • Confirm with a signature where appropriate. suitable when quality welds are extremely important. Private gardening - motorcycles,...
-
Page 3: Table Of Contents
AC/DC WIG SERIES EQUIPMENT Safety instructions Safety instructions WARNING 1.1 Arc welding damage--------------------------------------------------------------01-04 1.2 Effects of low frequency electric and magnetic fields----------------------- 04-04 PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING 1.3 Symbol chart------------------------------------------------------------------------ 05-05 YOUR DOCTOR. -
Page 4: Safety Instructions Warning
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Safety instructions Safety instructions 6. Be aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side. 7. Do not weld on closed containers such as tanks or drums. ARC RAYS can burn eyes and skin, WARNING 8. -
Page 5: Effects Of Low Frequency Electric And Magnetic Fields
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Safety instructions Safety instructions 1.3 Symbol Chart Note that only some of these symbols will appear on your model. WARNING MOVING PARTS can cause injury. Moving parts, such as fans, rotors, and belts can cut fingers and hands and catch loose clothing. -
Page 6: Summary
2) The workpiece gets little heat. Arc energy is focused. Be suitable for thin sheet The parameters of TIG London2400 AC/DC on the front panel all can be adjusted con- and super thin sheet welding. -
Page 7: Volt- Ampere Characteristic
2.3 Volt- Ampere Characteristic ratings, all capacities, measurements, dimensions and weights quoted are approximate only. Achievable capacities and ratings in use and operation will depend upon correct TIG London2400 AC/ DC welding installation, use, applications, maintenance and service. machine has an excellent volt-ampere characteristic, whose graph is shown as the following figure. -
Page 8: Operation
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Operation Operation Behind 3.1 Layout For The Panel Front 9 16... - Page 9 AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Operation Operation 1. Digital Ammeter / Parameter meter 9. Frequency Indicator (Hz) The digital Ammeter is used to display the actual output current of the power source. It is Frequency indicator, when the setting programm in pulse frequency ,this indicator will also used to display Parameters in Programming Mode.
-
Page 10: Control Panel
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Operation Operation 13. Process Selection Button 19. 5 Pin Control Socket The process selection control is used to select the desired welding mode. Two modes The 5 pin receptacle is used to connect a trigger switch or remote control to the welding are available, GTAW (TIG), and MMA (Stick) modes. - Page 11 AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Operation Operation 3.Up Slope 11. AC Frequency Setting ranges :0.1S-10S (0.1S increments) Setting ranges 50HZ-200HZ This parameter operates in (2T and 4T) TIG modes only and is used to set the time for the This parameter operates in AC TIG mode only and is used to set the frequency for the weld current to ramp up, after the torch trigger switch has been pressed then released, AC weld current.
-
Page 12: Setup For Stick (Mma) Welding
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Operation Operation 3.4 Set-up For LIFT TIG (GTAW) Welding Before any welding is to begin, be sure to wear all appropriate and recommended safety equipment. Wider bead and cleaning action Narrower bead, with no visible cleaning WARNING NOTE The following set up is known as Straight Polarity or DC electrode positive. -
Page 13: Operation Environment
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Welding technique Operation 3.5 Operation Environment 4.2 Joint froms in TIG ◆ Height above sea level is below 1000m. ◆ Operation temperature range:-10˚C~+40˚C. ◆ Relative humidity is below 90%(20˚C). ◆ Preferably site the machine some angles above the floor level,the maximum angle does not exceed 15˚. -
Page 14: Mma Basic Welding Technique
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Welding technique Welding technique Parameters of AC TIG(MMA) for Aluinum and its alloy Tungsten Electrode Tungsten Sharpened of Tungsten Welding Background Gas nozzle Steet Pre-heat Angle of Cone(º) Electrode the Electrode wire eletrode Argon flow Current/a... -
Page 15: Troubleshooting
AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Welding technique Troubleshooting 5.1 Troubleshooting ◆Before arc welding machines are dispatched from the factory, they have already been debugged accurately. So forbid anyone who is not authorized by us to do any change to Vertical Position, the equipment! Vertical Position,... - Page 16 AC/DC WIG SERIES EQUIPMENT AC/DC WIG SERIES EQUIPMENT Troubleshooting Troubleshooting Solution Solution Troubles Reasons Troubles Reasons The welding cable is not connected Connect the welding cable to The power board is broken Repair or change it with the two output if the welder the welder's output No AC output The AC drive board damaged...
-
Page 17: Maintenance
AC/DC WIG SERIES EQUIPMENT Maintenance 6.1 Maintenance In order to guarantee that arc welding machine works high-efficiently and in safety,it must be maintained regularly.Let customers understand the maintenance methods and means of arc welding machine more, enable customers to carry on simple examination and safeguarding by oneself,try one’s best to reduce the fault rate and repair times of arc welding machine, so as to lengthen service life of arc welding machine.Maintenance items in detail are in the following table.