Subscribe to Our Youtube Channel
Related Manuals for Vector Welding Tokyo 2300
Summary of Contents for Vector Welding Tokyo 2300
- Page 1 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Tokyo2300 Welding Machine Register now and benefit! Jetzt Registrieren und Profitieren! www.smart-iwm.com...
- Page 2 • Observe accident prevention regulations! • Observe all local regulations! VECTOR welding equipment can be used on nearly all weld able metals. It is particularly • Confirm with a signature where appropriate. suitable when quality welds are extremely important. Private gardening - motorcycles,...
-
Page 3: Table Of Contents
DC PULSE SERIES EQUIPMENT Safety instructions Safety instructions WARNING 1.1 Arc welding damage--------------------------------------------------------------01-04 1.2 Effects of low frequency electric and magnetic fields----------------------- 04-04 PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING 1.3 Symbol chart------------------------------------------------------------------------ 05-05 YOUR DOCTOR. -
Page 4: Safety Instructions Warning
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Safety instructions Safety instructions 6. Be aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side. 7. Do not weld on closed containers such as tanks or drums. ARC RAYS can burn eyes and skin, WARNING 8. -
Page 5: Effects Of Low Frequency Electric And Magnetic Fields
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Safety instructions Safety instructions 1.3 Symbol Chart Note that only some of these symbols will appear on your model. WARNING MOVING PARTS can cause injury. Moving parts, such as fans, rotors, and belts can cut fingers and hands and catch loose clothing. -
Page 6: Summary
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Summary Summary 2) The workpiece gets little heat. Arc energy is focused. Be suitable for thin sheet 2.1 Brief Introduction and super thin sheet welding. 3) Exactly control heat input and the size of the molten pool. The depth of penetration Tokyo2300 welding machine adopts the latest pulse width modulation (PWM) technology is even. -
Page 7: Volt- Ampere Characteristic
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Summary Summary NOTE 2.3 Volt- Ampere Characteristic Note 1: The Effective Input Current should be used for the determination of cable size & supply requirements. Tokyo2300 welding machine has an Note 2: Generator Requirements at the Maximum Output Duty Cycle. excellent volt-ampere characteristic, whose graph is shown as the following Note 3: Motor start fuses or thermal circuit breakers are recommended for this application. -
Page 8: Operation
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Operation Operation 3.1 Layout For The Panel Behind Front... - Page 9 DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Operation Operation 1. Digital Ammeter / Parameter meter Anti-stick prevents the electrode from annealing. Antistick If the electrode sticks in spite of the arcrorce device, the The digital Ammeter is used to display the actual output current of the power source. It is m a c h i n e a u t o m a t i c a l l y s w i t c h e s o v e r t o t h e m i n i m u m also used to display Parameters in Programming Mode.
- Page 10 DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Operation Operation 13. Process Selection Button 18. Shielding Gas Outlet The process selection control is used to select the desired welding mode. Two modes The Shielding Gas Outlet located on the front panel is a fast connection of a suitable TIG Torch.
-
Page 11: Control Panel
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Operation Operation 7.End current 3.2 Control Panel Setting ranges 10A-170A This parameter operates in (4T) TIG modes only and is used to set the finish current for TIG. The end Current remains ON until the torch trigger switch is released after it has been depressed. -
Page 12: Set-Up For Lift Tig (Gtaw) Welding
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Operation Operation 4. Slowly open the Argon Cylinder Valve to the fully open position. 5. Connect the work lead clamp to your work piece. 6. The tungsten must be ground to a blunt point (similar to a pencil) in order to achieve power supply optimum welding results. -
Page 13: Operation Environment
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Welding technique Operation 3.5 Operation Environment 4.1 TIG Basic Welding Technique Gas Tungsten Arc Welding (GTAW) or TIG (Tungsten Inert Gas) as it is commonly referred ◆ Height above sea level is below 1000m. to, is a welding process in which fusion is produced by an electric arc that is established between a single tungsten (non- consumable) electrode and the work piece. -
Page 14: Tig Parameters Matching
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Welding technique Welding technique The relation of welding area color & protect effect of Ti-alloy TIG of stainless steel(single run welding) Welding area color bright argent orange-yellow blue-purple caesious white powder tungsten welding welding Argon gas... -
Page 15: Mma Basic Welding Technique
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Welding technique Welding technique Parameters of AC TIG(MMA) for Aluinum and its alloy Tungsten Welding Gas nozzle Steet Pre-heat wire eletrode Argon flow Welding diameter thickness Temper Remark diameter Horizontal Position, Horizontal-Vertical diameter rate/L•min- Flat Position,... -
Page 16: Troubleshooting
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Troubleshooting Troubleshooting Troubles Reasons Solution 5.1 Troubleshooting Wait a few minutes, the machine If the overheat indicator is on can be operated normal No no-load ◆Before arc welding machines are dispatched from the factory, they have already been The main circuit is broken Check and repair voltage output... -
Page 17: Maintenance
DC PULSE SERIES EQUIPMENT DC PULSE SERIES EQUIPMENT Maintenance Troubleshooting Solution Troubles Reasons 6.1 Maintenance Checking if the electorde stick to Separate the electrode and the work piece that the anti-stick In order to guarantee that arc welding machine works high-efficiently and in safety,it must The welding work piece function is on...
Need help?
Do you have a question about the Tokyo 2300 and is the answer not in the manual?
Questions and answers