EC-DECLARATION OF CONFORMITY in accordance with the EU Machinery Directive 2006/42/EC applicable as from December 29 2009: HE-VA ApS N. A. Christensensvej 34, DK-7900 Nykøbing Mors hereby confirms that the following machine has been manufactured in accordance with the Council Directive 2006/42/EC.
Combi-Tiller is a sub-soiler developed for working solo or combined with a stubble implement or a drill unit. The Combi-Tiller MKII lifts the soil to break hard stratum of earth/plough pan together with an oxidation of the soil – without bringing large unwanted clods to the surface. The Combi-Tiller has a working depth from -50 mm down to 300 mm.
Combi-Tiller MK II 30/04-2019 Safety instructions for Combi-Tiller Do not start-up the machine if there are persons in exposed positions* within a hazardous area**. When persons are in exposed positions (e.g. in connection with adjustment, maintenance, attachment and uncoupling), the following conditions must be observed: The machine must be lowered to firm ground.
Combi-Tiller MK II 30/04-2019 Safety and Instructions on Hydraulics The maximum working pressure is 225 bar. It is advisable to label the attachment parts at hydraulic connections between the tractor and the tool in order to eliminate incorrect operation! When checking for hydraulic leaks, use suitable safety wear (eye protectors, gloves, etc.) High-pressure hydraulic oil may penetrate the skin and cause dangerous injuries.
Combi-Tiller MK II 30/04-2019 Labels on the machine You will find several labels on your machine containing safety and practical instructions as regards the correct application of the machine. Please study the instructions and point out to the user the importance of the labels as well as the safety instructions in the Operating Instructions.
Combi-Tiller MK II 30/04-2019 Start-up of the machine General information The machine requires 1 double acting outlet (rigid). The machine requires 2 double acting outlets (hydraulic). The hoses for depth adjustment are provided with red cable straps. Attachment und uncoupling : Combi-Tiller - three-point mounted models.
Combi-Tiller MK II 30/04-2019 Settings and adjustment Stone protection Quick-Push shear bolt When the shear bolt is broken and the tine has been released, place the shear bolt one notch forward before the machine can operate again. Pull out the R-clip (Pos. 1). Pull the tine back to normal working position (Pos.
Combi-Tiller MK II 30/04-2019 Hydraulic automatic release system Before each season it has to be controlled, that the gas pressure in the accumulator (Pos.1) is 90 bars. This requires special tools and can only be performed by an authorized dealer. Before the start-up of the machine the hydraulic pressure in the closed hydraulic stone protection system has to be controlled on the machine’s pressure gauge (Pos.
Combi-Tiller MK II 30/04-2019 It is important that no persons are near to the machine as the tine is returning to the working position with high speed and might throw with soil and stones. Replacement of wearing point Before working with the machine’s wearing points, the machine is to be fastened. This can be performed by trestles under the main frame.
Page 12
Combi-Tiller MK II 30/04-2019 Back to the table of contents...
Combi-Tiller MK II 30/04-2019 Maintenance After 10 hours of operation, retighten the machine. Check hydraulic hoses, fittings and cylinders for leaks and retighten. Further check on a regular basis that all bolts are tightened. Before the winter storage, wash and lubricate the machine. If you use high-pressure cleaner, do not spray directly on the ball bearings.
Combi-Tiller MK II 30/04-2019 Frame and three-point linkage, rigid model 3.0 – 3.5 – 4.0 m Pos. Item no. Designation 3.0 m 3.5 m 4.0 m 645200090 Frame 645200091 Frame 645200213 Frame 645200092 Frame 69532100J Pin for top link: Ø32 L=100 69532105C Pin for top link.
Combi-Tiller MK II 30/04-2019 Pos. Item no. Designation 4.0 m 5.0 m 645200016 Frame 645200013 Support leg 690302025 Top link strengthened 69440155G Pin Ø40 L=155 69530175G Pin Ø30 L=175 69440187G Pin Ø40 L=187 69532119J Pin for top link Ø32 L=119 69537129B Pin for liftarm Ø37 L=129 690134008...
Combi-Tiller MK II 30/04-2019 Wing section Pos. Item no. Designation 4.0 m 5.0 m Pos. Item no. 645200191 Designation Wing section, left 4.0 m 5.0 m 645200196 Wing section, right 630931052 Drawbar 645200197 Wing section, right 630771200 Parking device f/hoses 645200198 Wing section, left 690200258...
Combi-Tiller MK II 30/04-2019 Tine Tine types Pcs. per machine Pos. Designation 3.0 m 3.5 m 4.0 m 4.0 m 5.0 m rigid rigid rigid hydr. hydr. Quick-Push mechanical Long – Right release system Quick-Push mechanical Long – Left release system Quick-Push mechanical Short –...
Combi-Tiller MK II 30/04-2019 Quick-Push tines, spare parts up to machine no. : 200454 Drawing Pos. Item no. Designation Per tine 645000044 Wearing point 645200059 Tine bracket, long right 645200060 Tine bracket, long left 645200057 Tine bracket, short right 645200058 Tine bracket, short left 645200046 645000059...
Combi-Tiller MK II 30/04-2019 Quick-Push tines, spare parts from machine no. : 200455 Drawing Pos. Item no. Designation Per tine 645000044 Wearing point 645200183 Tine bracket, long right 645200185 Tine bracket, long left 645200187 Tine bracket, short right 645200188 Tine bracket, short left 645200184 690103869 Bolt M30x110 10.9...
Combi-Tiller MK II 30/04-2019 The number of hoses and hose lengths can vary – dependent on the machine type , therefore check measurements and number before ordering the spare parts. Drawbar: Pos. Item no. Designation Number 690200258 Cylinder 90/40x280mm Ø35/Ø32 690200268 Gasket set 90/40 (Klinkby) 690200274...
Combi-Tiller MK II 30/04-2019 The number of hoses and hose lengths can vary – dependent on the machine type, therefore check measurements and number before ordering the spare parts. Linkage Pos. Item no. Designation Number 690203001 Quick coupling 1/2", male 690203103 Fitting straight Ø12 x1/2"...
Combi-Tiller MK II 30/04-2019 The number of hoses and hose lengths can vary – dependent on the machine type, therefore check measurements and number before ordering the spare parts. Hydraulics for automatic release system (rigid) Back to the table of contents...
Page 29
Combi-Tiller MK II 30/04-2019 Pos. Item no. Designation Number 690206513 Accumulator 4.5 l 90 bar Fitting straight ½” x 1 ¼” 690204501 Fitting straight Ø15 mm x ½” 690204512 690204500 Fitting 90angle Ø15 mm premounted union nut 690204502 Fitting T Ø15L 690204503 Olive ring Ø15 690204504...
Page 30
Combi-Tiller MK II 30/04-2019 Back to the table of contents...
Combi-Tiller MK II 30/04-2019 The number of hoses and hose lengths can vary – dependent on the machine type, therefore check measurements and number before ordering the spare parts. Notes: Back to the table of contents...
Page 34
Denmark The design is subject to modification without notice.