Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Screen Innovations Sail
Summary of Contents for Screen Innovations Sail
- Page 1 Sail Installation manual 1 - 03.2018 SCREEN INNOVATIONS...
-
Page 3: Table Of Contents
All unauthorized interventions (tampering, technical modification etc.) during the warranty Electrical connections period will invalidate said warranty. Motor programming Screen Innovations. reserves the right to make technical modifications to the Anemometer programming components or products, except for the main features, at any time and without prior Awning cover notice. -
Page 4: Symbols
GENERAL SAFETY WARNINGS Sail is designed for a specific use (as outlined in this manual); any use other than that envisaged shall relieve Screen Innovations of any responsibility. -
Page 5: Preliminary Checks
REPEAT ALL THE ASSEMBLY OPERATIONS IN REVERSE ORDER, TO AVOID LOSING THE SYNCHRONY OF MOVEMENTS AND/OR DAMAGING COMPONENTS, SO THAT THE SUBSEQUENT REASSEMBLY OPERATIONS CAN BE PERFORMED CORRECTLY AS DESCRIBED IN THIS MANUAL. SCREEN INNOVATIONS WILL NOT BE LIABLE FOR ANY FAILURES ARISING FROM INCORRECT DISASSEMBLY. -
Page 6: Material Check, Unpacking And Preparation
Do not use a knife to avoid the risk of ruining the paint or metal elements or the canvas fabric. 4 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS- INSTALLATION MANUAL- SAIL... -
Page 7: Versions And Packing
WEIGHTS AND DIMS 210.25'' 133.875' 133.875'' 89.75'' 133.25'' 107.75'' 101'' 204.75 10'' 25'' 94.5'' Shaped pole and accessories 3.5'' 42.5'' 42.5'' Pedestal 10.5'' 10.5'' Roller tube pre-fitted with canvases Rev.1 - 03.2018 5 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... -
Page 8: Base Preparation
BASE PREPARATION NOTE: Base is optional, pole can be mounted directly to the ground. NOTE: Appropriate anchors must be specified if securing directly to the ground (see page 28) Use a spirit level to check that the base (A) is perfectly flat once in position. Position the eight ballast tiles (B) (not supplied) in the respective seats in the base (A). - Page 9 NOTE: Appropriate anchors must be specified if securing directly to the ground (see page 28) Position the cover (C) on the ballasted base. Route the heaving line through the central hole (D) of the cover. Rev.1 - 03.2018 7 of 28 SCREEN INNOVATIONS - INSTALLATIONMANUAL - SAIL...
-
Page 10: Assembling The Pole
Insert the shaped pole (A) into the vertical support pole (B), locking it using the knob (C). line and the power cable together using insulating tape. The task of the knob (C) is to prevent the shaped pole from rotating. 8 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... - Page 11 Lift the vertical support pole (A) and rest it in correspondence with the relative holes on the If Sail is fastened directly to the ground, mark out the holes using the plate of the pole assembled base (B) or on the ground, and simultaneously pull the heaving line (E) until the power (A) as a template, drill into the ground using a suitable bit and fasten the pole using cable comes out of the base (B).
-
Page 12: Assembling The Roller Tube Group
Insert the recessed and drilled side of the central arm (A) in correspondence with the drilled plate (B) on the shaped pole. NOTE: TWO PEOPLE ARE RECOMMENDED FOR THESE OPERATIONS. 10 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... - Page 13 ASSEMBLING THE ROLLER TUBE GROUP Insert the fastening screw provided (A). Rev.1 - 03.2018 11 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 14 Attach the central upper rope (A) to the upper hole on the fitting (B) at the end of the roller tube NOTE: Two operators are required for this operation. pole (C). 12 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 15 Insert the recessed and drilled side of the side arm (D) in correspondence with the drilled plate (E) on the left-hand side of the shaped pole and tighten using the screw provided. Rev.1 - 03.2018 13 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 16 Join the coupling element (A) of the side rope (B) in the side attachment plate at the end of the of the side arm (C). left side arm (C). NOTE 14 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 17 NOTE: Reconnect the hook (D) to the eyelet of the left-hand awning (E). Fit the block (A), as shown in the callout, in the eyelet (B) of the shaped pole on the left-hand side. Rev.1 - 03.2018 15 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 18 Release the spring clip (B) at the end of the rope (C) from the eyelet of the right-hand canvas (D). Cut the two BLACK ties (A) binding the left side arm (B) SIMULTANEOUSLY. NOTE: Two operators are required for this operation. 16 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 19 Join the coupling element (A) of the upper side rope (B) in the upper attachment plate at the end plate (B) on the shaped pole and tighten using the screws provided. of the side arm (C). Rev.1 - 03.2018 17 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 20 ASSEMBLING THE ROLLER TUBE GROUP Join the coupling element (A) of the side rope (B) in the side attachment plate at the end of the side arm (C). NOTE 18 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 21 ASSEMBLING THE ROLLER TUBE GROUP Fit the block (A), as shown in the callout, in the eyelet (B) of the shaped pole on the right-hand side. Rev.1 - 03.2018 19 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 22 Join the coupling element (A) of the central lower rope (B) to the lower hole on the fitting (C) at Couple the spring clip (A) in the eyelet of the right-hand awning (B). the end of the central arm (D). NOTE 20 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
-
Page 23: Electrical Connections
Tighten the plug (A) to the appropriate connector (B), taking care not to tighten it too much. the bracket (A) fastened to the anemometer with the screws provided (B). 21 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... - Page 24 110V Wiring present in the awning with motor, anemometer and light configuration. Ground Rev.1 - 03.2018 22 of 28 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
- Page 25 OPTIONAL Mount the lamp bracket (A) to the long pole using the screws provided (B). Connect the electrical wiring. 23 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL...
-
Page 26: Motor Programming
- Power the motor. - Press the “up arrow” (A) and “down arrow” keys (C) simultaneously. - Check the direction of rotation by pressing the “up arrow” A (the sail closes) and “down arrow” keys C (the sail opens). - If the direction (open/close) is incorrect, press MY (B) until the motor performs an UP/ DOWN movement. -
Page 27: Anemometer Programming
N.B.: Do not tamper with the seal covering the wind intensity regulator (preset by the manufacturer). Breakage of or even partial tampering with the seal invalidates the warranty and relieves the manufacturer of any liability for resulting damages. 25 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... -
Page 28: Awning Cover
Release the two spring clips (A) from slots (B) and couple them to slots (C). Turn the two arms (D) until they are alongside the wind-up device pillar. Wind up the sail completely and cover with the sail cover (E). Fold the sail cover over with the Velcro side. -
Page 29: Data Sheets
DATA SHEET 2 - BALLAST FOR COUNTER-WEIGHT ASSEMBLY 50x50x3 cm = 168 Kg = 370 lbs Sail Degree 3 (8 plates) 20x20x1 in * weight of single plate = 21 Kg = 46lbs Rev.1 - 03.2018 27 of 34 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... -
Page 30: Calculation Of Wind Resistance Based On The Loads And The Anchors
C) Use a loads data sheet for a lower wind speed and assign the consequent wind resistance to the product installed. For the correct choice and use of anchors, * data taken from the HILTI technical sheets (ST_HY 70_2008.PDF page 259-261 and hsl-3.PDF page 62-63) 28 of 28 Rev.1 - 03.2018 SCREEN INNOVATIONS - INSTALLATION MANUAL - SAIL... - Page 31 Page left intentionally blank...