Related Manuals for Screen Innovations Zen Roll
Summary of Contents for Screen Innovations Zen Roll
- Page 1 Zen Roll Owner’s Manual With ShyZip Tracks ® 512-832-6939 9715-B Burnet Road Suite 400, Austin,TX 78758 screeninnovations.com INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER. ZRS-X1...
- Page 2 Innovations’ option) the defective part of the merchandise. Returns for service should be made to your Screen Innovations' dealer. If it is necessary for the dealer to return the screen or part to Screen Innovations, transportation expenses to and from Screen Innovations are payable by the purchaser and Screen Innovations is not responsible for damage in shipment.
-
Page 3: Table Of Contents
TABLE OF CONTENTS OPERATING AND MAINTAINING YOUR SHADE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4 BEFORE PROCEEDING �... -
Page 4: Operating And Maintaining Your Shade
OPERATING AND MAINTAINING YOUR SHADE • Operation of the shade systems should only be completed by qualified person(s) • Always monitor the operation of the Shade Systems to ensure proper operation and that furniture or other obstacles cannot prevent normal deployment or retraction of the shade system •... -
Page 5: Before Proceeding
BEFORE PROCEEDING CAUTION: READ THE INSTRUCTIONS IN THEIR ENTIRETY BEFORE PROCEEDING. ACTIONS CONTRARY TO THE INSTRUCTIONS INVALIDATE THE WARRANTY AND MAY RESULT IN SERIOUS DAMAGE AND/OR INJURY. Preparing for your installation: It is crucial that all installations are planned out carefully before specifying a shade order. •... -
Page 6: Specifying Your Shade Dimensions
SPECIFYING YOUR SHADE DIMENSIONS BETWEEN COLUMNS MOUNT Use these formulas for specifying shades were the case and guide tracks can be seen from the inside of the installation opening. For new construction or difficult installations it is advised to order and install the tracks first. - Page 7 SPECIFYING YOUR SHADE DIMENSIONS WALL SURFACE MOUNT Use these formulas for specifying shades where the case and guide tracks can NOT be seen from the inside of the opening. For new construction or difficult installations it is advised to order and install the tracks first.
-
Page 8: Parts List
PARTS LIST Material Roll Assembly 1 Left and 1 Right ShyZip Track Assemblies Motor Bracket Idler Bracket Accessories Options For Motorized Shades ONLY For Manual Shades Only 1X Foldable Crank Handle 1X Telis Remote... -
Page 9: Install Brackets
INSTALL BRACKETS LEVEL UNIT WIDTH 16 " 16 " 16 " 4 " 4" 16 " 16 " 8 " 16 " 4 " APPROX DEPENDENT ON MATERIAL AND DROP Mount the motor and idler brackets to structural supports as shown� Refer to your order or the packaging to get the UNIT WIDTH = W and make sure the brackets measure the same UNIT WIDTH dimension from outside to outside�... -
Page 10: Install Material Roll
INSTALLATION REQUIRES TWO OR MORE PEOPLE. PLEASE USE SAFE LIFTING AND RIGGING TECHNIQUES. INSTALL MATERIAL ROLL Remove the screw from the idler side bracket, then remove the idler bushing and install on the material roll idler shaft� Use 2 people to lift up the material roll and guide the motor into the star bracket� Make sure the power and control cables exit the desired direction�... -
Page 11: Install Material Roll
INSTALL MATERIAL ROLL Lift the idler end with bushing already installed up into the idler housing� Then secure with the screw removed in step 1� ZRS-X1... -
Page 12: Cutting Track To Length
CUTTING TRACK TO LENGTH TOP LEFT TOP RIGHT L-5’’ R-5’’ CUT THIS END Measure the distance from the top of the mounting brackets to the floor. Then cut the bottom end of each assembled track to 5’’ less than the measured length� DO NOT cut the top of the track as denoted by the plastic portion sticking out of the top�... -
Page 13: Installing The Tracks
INSTALLING THE TRACKS Removable Cover Fixed Track Zipper Track Disassemble the track by removing the screws holding the removable extrusion cover and removing the plastic zipper track on the inside� Make sure the bottom cap is installed before proceeding� ZRS-X1... - Page 14 INSTALLING THE TRACKS FRONT MOUNT SIDE MOUNT Align the track with the screen material zipper� Notches for mounting from the front or side have been provided to guide fastener installation� Use appropriate fasteners to secure the track to the installation location� Make sure that the tracks are mounted level and plumb in ALL directions.
- Page 15 INSTALLING THE TRACKS Angle the zipper track up into and behind the upper most spring� The top of the track is the side with the notches cut out� Then slide it up into the zipper on the shade material until it is pushed all the way up to the track top cap.
- Page 16 INSTALLING THE TRACKS DO NOT USE POWERED SCREW DRIVER TO AVOID STRIPPING SCREWS. Place the removable cover onto the fixed track and hold into place while securing with the retaining screws�...
-
Page 17: Power (Motorized Only)
POWER (MOTORIZED ONLY) TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH THE APPROPRIATE ELECTRICAL CODES AND REGULATIONS BY A LICENSED ELECTRICAL PROFESSIONAL. DO NOT CONNECT POWER WITH THE CIRCUIT BREAKER ON. BEFORE CONNECTING POWER TO MULTIPLE UNITS BE AWARE THAT THE LIMITS MUST BE SET WITH POWER CONNECTED TO ONLY ONE UNIT AT A TIME. -
Page 18: Set Limits (Motorized Only)
QUICK PROGRAMMING GUIDE FOR ALL RTS MOTORS SET LIMITS (MOTORIZED ONLY) Altus RTS 120 V / Sonesse 30 24V / Wirefree Roll Up LT-30RT Round Head & CORD Lift CT-32 Motors. Please refer to individual instructions for more details Programming Mode STEP 4: Set the limits Bring the shade to desired upper limit stop point. -
Page 19: Troubleshooting
TROUBLESHOOTING Problems related to electrical or motor function may require a qualified service person or electrician. Should you have a problem that is not addressed here, call: Screen Innovations (512-832-6939.) http://www.screeninnovations.com/category/support/ Problem Description Probably Cause Action to Take Motor shuts off. Motor has been in Motor is designed for short Allow the motor to cool down. - Page 20 NOTES...