Screen Innovations Nano Roll 275 Series Installation Instructions Manual
24vdc - sdn
Hide thumbs
Also See for Nano Roll 275 Series:
- Installation instructions manual (6 pages) ,
- Manual operation instructions (7 pages) ,
- Installation instructions manual (20 pages)
Related Manuals for Screen Innovations Nano Roll 275 Series
Summary of Contents for Screen Innovations Nano Roll 275 Series
- Page 1 Nano Roll Installation Instructions Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 24VDC - SDN 512.832.6939 www.screeninnovations.com INSTALLERS: Please leave this manual with the owner. PART NO. 400030 Version 1.0...
- Page 2 PARTS LIST - NANO ROLL - 24VDC - SDN PARTS LIST - NANO ROLL - 24VDC - SDN Shades Terminal Blocks Spacer Blocks (optional) 275 Roll 375 Roll 475 Roll Leveling Shims (optional) Wall Brackets (275) + End Caps Motor Side Idler Side Screws included (3 per bracket) Wall Brackets (375 / 475) + End Caps...
-
Page 3: Additional Accessories
ADDITIONAL ACCESSORIES SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL) Spacer Blocks - used to clear an obstruction in the fabric path. 5/16” Magnetic Driver Set Screw Hex Tool (1/16”) Included with 375 / 475 series only 1/4” Magnetic Driver Connect spacer blocks to shade brackets before installation. Note: Do not use more than 4 spacer blocks per bracket. - Page 4 INSTALLATION - 24 VDC - SDN (275 SERIES) INSTALLATION - 24 VDC - SDN (275 SERIES) Before installing the shades, verify whether the shade was ordered as standard roll or reverse roll. Though illustrations in this manual show standard roll shades, the installation for reverse roll shades is the same. 3.
- Page 5 INSTALLATION - 24 VDC - SDN (275 SERIES) INSTALLATION - 24 VDC - SDN (275 SERIES) 5. Connect shade and pre-wire connectors, snap into bracket 6. Insert motor side completely. Then, while supporting motor side, put idler end cap over the idler and snap into place.
- Page 6 INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) 3. Install wall bracket/end cap assembly with the supplied screws 1. Terminate pre-wire with terminal block Header for Ceiling Mount for Wall Mount + 24 VDC...
- Page 7 INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) 5. Remove both end caps 6. Connect shade and pre-wire, snap connector into spring clip. 1/16” hex tool Motor End cap 7.
- Page 8 INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) INSTALLATION - 24 VDC - SDN (375 / 475 SERIES) 8. Make sure the motor head bracket is fully seated. Secure with cotter pin. 9. Put idler end cap over idler and snap into place. There will be an audible click.
- Page 9 PROGRAMMING SDN 10. Replace and fasten motor end cap SDN shades are programmed using the Screen Innovations SIFI via the web interface. This programming can be done with a Windows or Mac computer either over LAN or wired directly to SIFI.
-
Page 10: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING Tech Support: 512.832.6939 Problem Possible Cause Action to Take Ensure that 24V hardwired motors have at least Shade won’t Motor is not powered. 20VDC and that the polarity is correct. operate. Check the wire pinouts and termination. Look for Incorrect or poor cable broken, loose, or damaged wires.