Screen Innovations Nano Box Installation Instructions Manual
24v dc - 485 shades
Hide thumbs
Also See for Nano Box:
- Installation instructions manual (6 pages) ,
- Installation instructions manual (6 pages) ,
- Installation instructions manual (6 pages)
Related Manuals for Screen Innovations Nano Box
Summary of Contents for Screen Innovations Nano Box
- Page 1 Nano Box Installation Instructions 24v DC - 485 INSTALLERS: Please leave this manual with the owner. ® Doc. # 400025...
- Page 2 PARTS LIST - NANO BOX - 24v DC - 485 Shades Wall Brackets 275 Box 375 Box 475 Box Please note all the Node IDs on your Shade motors. Screws Included See the last page on these instructions. (3 per Bracket)
- Page 3 SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL) Spacer Blocks - used to clear an obstruction in the fabric path. Connect spacer blocks to shade brackets before installation. Note: Do not use more than 4 spacer blocks per bracket. Leveling Shims - used if the window frame is out of level. Connect to shade brackets before installation Note: Do not use more than 2 leveling shims per bracket.
- Page 4 INSTALLATION - 24v DC - 485 1. Terminate pre-wire with the supplied terminal block. Header + 24 VDC - 24 VDC Data + Data For 485 Only Data - Data ground 2. Install wall brackets 4 - 6 inches from the jamb using the supplied screws. (The closer to the end of the cassette, the better) 4”...
- Page 5 INSTALLATION - 24v DC - 485 3. Make sure the wall bracket lever is down (may already be down). Proper position for installing Box 4. Install terminal block bracket between jamb and wall bracket on the motor side using the supplied screws Header 4”...
- Page 6 INSTALLATION - 24v DC - 485 5. Connect the shade and pre-wire connectors, then snap into the terminal block bracket 6. Hang shade onto wall brackets and center in opening 7. Use thumb to lock shade in place Installation - 24v DC 485...
- Page 7 WIRING - 485 24v DC - Using 5 Conductor Wire Pre-wire Shade Marking Description Wire Gauge (AWG) Maximum Supported Wire Length (FT.) Positive 24VDC Negative 24VDC 485 Data Positive 485 Data Negative 485 Data Ground 24v DC - Using UTP wire Wire between Janus terminal block face and the motor only.
- Page 8 WIRING - 485 RJ45 DATA CABLE FOR DATA HUB ONLY If the shade will be connected to a Data Hub or Power Panel device port for data, terminate with the following pinout: 485 Wiring Port Pin 1 Pin 8 Utilizing RJ-45 TIA-568B termination standard Pin# Color Function...
- Page 9 PROGRAMMING - 485 485 shades are programmed using the Screen Innovations SIFI via the web interface. This programming can be done with a Windows or Mac computer either over LAN or wired directly to SIFI. The following instructions are for a Windows computer, but the steps for programming on a Mac are very similar.
-
Page 10: Troubleshooting - 485
TROUBLESHOOTING - 485 Tech Support: 512.832.6939 Problem Possible Cause Action to Take Ensure that 24Volt motors have 24v DC supply and Shade won’t Motor is not powered. that the polarity is correct. operate. Check the wire pinouts and termination. Look for Incorrect or poor cable broken, loose, or damaged wires. - Page 11 NODE IDS Please keep a note of all the Node IDs on your shade motors. OR for larger shade orders, refer to your Sales Order document for the list. Room Shade 1 Shade 2 Shade 3 Shade 4 Shade 5 Shade 6 Room Shade 1...
- Page 12 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com 400025 v. 1.4 2 June 2020...