Quick Reference - Fuji Electric PXV3 SERIES Operation Manual

PXW/PXV3 QUICK REFERENCE
Primary Menu
Parameter Range
roFF - rHLd roFF/rrUn/rHLd
H
AH 0 - 100%FS
L
* AL* 0 - 100%FS
HB
Hb 0.0 - 50.0A
AT 0 - 2
LoC 0 - 2
Secondary Menu
P 0.0 - 999.9%FS Proportional band
I 0 - 3200sec
D 0.0 - 999.9sec
TC 1 - 150sec
HYS 0 - 50%FS
TC2 1 - 150sec
CooL 0.0 - 100.0
db -50.0 - 50.0%FS
bAL 0 - 100%
Ar 0 - 100%FS
P-n2 0 - 16
P-SL -1999 - 9999
P-SU -1999 - 9999
P-dP 0 - 2
P-AH 0 - 11
* P-AL* 0 - 15
PVOF -10 - 10%FS
SVOF -50 - 50%FS
°C/°F
P-F
STAT --
SV-1 0 - 100%FS
TM1r 0 - 99hr 59min
TM1S 0 - 99hr 59min
SV-2 0 - 100%FS
TM2r 0 - 99hr 59min
TM2S 0 - 99hr 59min
SV-3 0 - 100%FS
TM3r 0 - 99hr 59min
TM3S 0 - 99hr 59min
SV-4 0 - 100%FS
TM4r 0 - 99hr 59min
TM4S 0 - 99hr 59min
MOD 0 -15
Description Default
settings settings
Ramp/soak command roFF
High Alarm Setpoint 10
Low Alarm Setpoint 10
Heater break alarm S.P. 0.0
Auto-tuning 0
Lock-out 0
5.0
Integral time 240
Derivative time 60
Cycle Time (output #1) †
Hysteresis 1
Cycle Time (output #2) †
Proportional band 1.0
coefficient for cooling
Deadband/Overlap 0.0
Balance 0.0/50.0 dSP2-128
Anti-reset wind-up 100%FS dSP3-1
Input type code †
Lower range of input 0%FS
Upper range of input 100%FS dSP3-8
Decimal point position 0
Alarm Type 1 code 5
Alarm Type 2 code 9
PV offset 0
SV offset 0
°C/°F selection †
Ramp/soak status oFF
1st S.P. 0%FS
1st ramping time 0.00
1st soaking time 0.00
2nd S.P. 0%FS
2nd ramping time 0.00
2nd soaking time 0.00
3rd S.P. 0%FS
3rd ramping time 0.00
3rd soaking time 0.00
4th S.P. 0%FS
4th ramping time 0.00
4th soaking time 0.00
Ramp/soak Mode code 0
Factory Preset Menu
Parameter
DSP
P-n1
P-dF
dSP1-1
P-An
dSP1-2
rCJ
dSP1-4
PLC1
dSP1-8
PHC1 -
dSP1-16
PLC2
dSP1-32
PHC2 -
PCUT -
dSP1-128
FUZY
dSP2-1
GAIN -
dSP2-2
ADJ0 -
dSP2-4
ADJS -
dSP2-8
OUT
dSP2-16
dSP1-7 0-255
dSP2-32
dSP2-64
* Not applicable to PXV3
† Based on the model
dSP3-2
dSP3-4
dSP3-16
dSP3-32
dSP3-64
dSP3-128
dSP4-1
dSP4-2
dSP4-4
dSP4-8
dSP4-16
dSP4-32
dSP4-64
dSP4-128
dSP5-1
dSP5-2
dSP5-4
dSP5-8
dSP5-16
dSP5-32
dSP5-64
dSP5-128
24
Range Description
0 -19 Control Action code
0.0 - 900.0sec Input Filter Constant
0 - 50%FS Alarm Hysteresis
- N/A
- N/A
N/A
- N/A
N/A
N/A
OFF/ON Fuzzy control
N/A
Zero calibration
Span calibration
- N/A
Parameter mask
Default DSP
settings settings
† dSP6-2
5.0 dSP6-4
1 dSP6-8
ON dSP6-16
-3.0 dSP6-32
103.0 dSP6-64
-3.0 dSP6-128
103.0 dSP7-1
0 dSP7-2
OFF dSP7-4
1 dSP7-8
0 dSP7-16
0 dSP7-32
-3.0 dSP7-64
† -