Quick Reference - Fuji Electric PXZ Series Operation Manual

PXZ QUICK REFERENCE
Primary Menu
Parameter Range
ProG oFF/rUn/HLd
P 0.0 - 999.9%FS
I 0 - 3200sec
D 0.0 - 999.9sec
AL 0 - 100%FS
AH 0 - 100%FS
TC 1 - 150sec
HYS 0 - 50%FS
Hb 0.0 - 50.0A
AT 0 - 2
TC2 1 - 150sec
CooL 0.0 - 100.0
db -50.0 - 50.0% FS Deadband/Overlap
PLC1 -
PHC1 -
PCUT -
bAL 0 - 100%
Ar 0 - 100%FS
LoC 0 - 2
STAT --
SV-1 0 - 100%FS
TM1r 0 - 99hr 59min
TM1S 0 - 99hr 59min
SV-2 0 - 100%FS
TM2r 0 - 99hr 59min
TM2S 0 - 99hr 59min
SV-3 0 - 100%FS
TM3r 0 - 99hr 59min
TM3S 0 - 99hr 59min
SV-4 0 - 100%FS
TM4r 0 - 99hr 59min
TM4S 0 - 99hr 59min
MOD 0 -15
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Description Default
settings settings
Ramp/soak command oFF dSP1-1
Proportional band 5.0 dSP1-2
Integral time 240 dSP1-4
Derivative time 60 dSP1-8
Low Alarm Setpoint 10 dSP1-16
High Alarm Setpoint 10 dSP1-32
Cycle Time (output #1) † dSP1-64
Hysteresis 1 dSP1-128
Heater-break alarm S.P. 0.0 dSP2-1
Auto-tuning command 0 dSP2-2
Cycle Time (output #2) † dSP2-4
Proportional band 1.0 dSP2-8
coefficient for cooling
0.0 dSP2-16
N/A -3.0 dSP2-32
N/A 103.0 dSP2-64
N/A 0 dSP2-128
Balance 0.0/50.0 dSP3-1
Anti-reset windup 100%FS dSP3-2
Lock out 0 dSP3-4
Ramp/soak status oFF dSP3-8
1st S.P. 0%FS dSP3-16
1st ramping time 0.00 dSP3-32
1st soaking time 0.00 dSP3-64
2nd S.P. 0%FS dSP3-128
2nd ramping time 0.00 dSP4-1
2nd soaking time 0.00 dSP4-2
3rd S.P. 0%FS dSP4-4
3rd ramping time 0.00 dSP4-8
3rd soaking time 0.00 dSP4-16
4th S.P. 0%FS dSP4-32
4th ramping time 0.00 dSP4-64
4th soaking time 0.00 dSP4-128
Ramp/Soak Mode code 0 dSP5-1
PXZ QUICK REFERENCE
Secondary Menu
DSP
Parameter
P-n1
P-n2
P-dF 0.0 - 900.0sec
P-SL
P-SU
P-AL
P-AH
P-An
P-dP
rCJ
PVOF
SVOF
P-F
PLC2
PHC2
FUZY
GAIN
ADJO
ADJS
OUT
dSP1-7
† Based on the model
22
Range Description
0 -19 Control Action code
0 - 16 Input type code
Input filter constant
-1999 - 9999 Lower range of input
-1999 - 9999 Upper range of input
0 - 15 Alarm Type 2 code
0 - 11 Alarm Type 1 code
0 - 50%FS Alarm Hysteresis
0 - 2 Decimal point position
- -
-10 - 10%FS PV offset
-50 - 50%FS SV offset
°C/°F
°C/°F Selection
- N/A
- N/A
OFF/ON Fuzzy control
- N/A
- Zero calibration
- Span calibration
- N/A
0-255 Parameter mask
Default DSP
settings settings
† dSP5-4
† dSP5-8
5.0 dSP5-16
0%FS dSP5-32
100%FS dSP5-64
9 dSP5-128
5 dSP6-1
1 dSP6-2
0 dSP6-4
ON dSP6-8
0 dSP6-16
0 dSP6-32
† dSP6-64
-3.0 dSP6-128
103.0 dSP7-1
OFF dSP7-2
1 dSP7-4
0 dSP7-8
0 dSP7-16
-3.0 dSP7-32
† -