Viss Signal; Repeat Playback - Panasonic AG-MD830E Service Manual

VISS Signal
After VISS has been set on the menu screen, the VISS
signal is automatically written on the tape when
recording is started.
It can also be written at the desired position on the tape
by pressing the REC Button and PLAY Button
simultaneously during recording.
• Locating particular scenes to be viewed becomes
easy if VI SS signals are written with each recording.
o
"VISS" blinks on the counter section while the VISS
signal is being written.
(t) Select at or 02 for VISS on the menu screen.
at: REC
02: REC/PAUSE
(2) Press the MEMORY Button to establish the memory
mode. "VISS" now lights on the counter section.
Memory mode Display Function
MEMORY
0
Playback is repeated at
REPEAT
the VISS write paint.
MEMORY 1 TIME Playback is repeated
REPEAT
;J
only once at the VISS
write pOint.
MEMORY STOP
-
The tape stops at the
VISS write point.
(3) Press the FF or REW Button.
When the VISS signal is located, the unit automat-
ically operates in accordance with the memory
mode.
o
Leave an interval of at least 30 seconds on the
tape for writing the VISS signal. (The signal will
not be detected' if the interval is less than 30
seconds long.)
VISS Setting
VISS signal writing rVISS
R
blinks
while the VISS signal is being writ-
ten)
REC/PLAV/ REC/PLAY
.l.
To be written
----~. __ ----------------_t~~-----+Time
i , STOP
REW
••• --------+ •• ~------~
: STOP , ,
REW
STOP
Memory
stop
(-)
~========:.~.=:.======:..-t~------~~~~ry
: PLAY
~ STOP
repeat
: (;;»
, , ,
,
,
REW
I
~ .~
:
~--<.~---.------
--....
: PLAY STOP
I
I
STOP
I
Unrecorded :
: blank search :
I
REW
, ,
u
~
•
~~-----~
PLAY
(Leave an interval of at
least 30 seconds between
VISS signals.)
, ,
Unrecorded
blank search
Continuous
repeat
(<:..:»
• Time
- E-12-
OPERATING INSTRUCTIONS
Repeat Playback
(1) Turn VISS function OFF:
1) Press the MEMORY (MEMO) Button and select
continuous repeat playback (MEMORY REPEAT
<:..:> )
or 1-time repeat playback (MEMORY 1 TIME
REPEAT;;> ).
MEMO
o
Press this and turn on
" <:..:>
"or" ;;>."
2) Press the BEGIN and END Buttons to set the
tape beginning and ending positions for repeat
playback.
BEGIN END
section
Repeat
~
1 - - - - - - - - Tape
3) Press the FF or REW Button.
(2) While "VISS" is on the display tube:
The VISS signal is used for repeat playback. (Refer
to the section on the VISS signal on page E-12.)
o
When the beginning and ending positions are the
same, the tape will be repeatedly played back be-
tween the beginning position and tape end.
o
When the ending position comes after the actual tape
end, the tape will be repeatedly played back between
the beginning position and tape end.
o
When the beginning position comes before the actual
tape beginning, the tape will be repeatedly played
back between the tape beginning and end position.
o
The precision of repeat playback may be impaired
when a short section (less than 20 seconds or so
long) of the tape is to be repeatedly played back.
BEGIN/END settings (set VISS to OFF on the
menu)
FF i REW
---+
u
,
STOP
,
, ,
,
REW
,
I
U
I
r
• .~
,
PLAY
: STOP
, ,
, ,
,
REW
i
,
~ .. 4
~
•
PLAY
t
BEGIN point END point
(Leave an interval 01 al
least 20 seconds between
BEGIN and END.)
Memory stop
(-)
1-time
memory
repeat
( ;;»
Continuous
repeat
(<:..:»
Time
- E-13-