Table of Contents
Advertisement
(Jl
Counter
indicator
No.
1008
1009
Superimposed
monitor
HI-FI REC
AUDIO DUB
Setting (underlin-
ing denotes de-
Description of function
fault setting)
00 : OFF
01 : ON
00 : CH1.CH2
01
CH1
02 : CH2
Hi-Fi audio recording (Cannot be used for audio DUB)
OFF:
Hi-Fi audio is not recorded.
ON:
Hi-Fi audio is recorded.
Selection of channel track for audio dubbing
CH1.CH2: The sound is added to CH1 and CH2 simul-
taneously.
CH1:
The sound is added to CH1.
CH2:
The sound is added to CH2.
1010
EDIT
00 : OFF (regular
Editing/regular operation selection
See Note 1
operation)
OFF:
Regular operation
01 : ON (editing/
ON:
For editing or dubbing
_________________ .... _______________________ d.ubbi.nJ!l _________________ . __ .... __________________________________ .
1 011
NOTCH
00 : OFF
For setting the NOTCH ON or OFF
See Note
2
01
ON
OFF:
?NoTCH OFF
ON:
NOTCH ON
The items shown below are displayed when the AG-IA823 serial interface board is used.
Counter
indicator
No.
Superimposed
monitor
Setting (underlin-
Ing denotes de-
Description of function
fault setting)
...
_---------------------_._-----------.----_
....
_-------------------------._
..
-
_
...
_--------------------_.-
..
_---_._--
3001
BIT LENGTH
3002
STOP BIT
3003
PARITY
3004
BAUD RATE
Notes:
00 : 7BIT
01 : 8BIT
00
STOP-1
01 : STOP-2
00 : ODD
01
EVEN
02 : NONE
00 : 1200
01 : 2400
02 : 4800
03 : 9600
Character length setting
7BIT:
7 bits
8BIT:
8 bits
Stop bit setting
STOP-1: 1 bit
STOP-2: 2 bits
Parity bit setting
ODD:
Odd
EVEN:
Even
NONE:
None
Baud rate setting
1200:
1200 bps
2400:
2400 bps
4800:
4800 bps
9600:
9600 bps
1. Edit
function:
When this is set ON, the noise reduction circuit for the video signals is set OFF. (The video noise will increase
!ilightly. For regular use, EDIT OFF recommended.)
2: NOTCH:
When there is high level of noise in the luminance signals, it may also affect the chrominance signals. In a case like
this, set the NOTCH to ON. Since the luminance signal band is reduced slightly when the filter is set to ON, the
NOTCH OFF position is recommended for regular use.
-E-10-
Counter Section
00
Memory Stop
RESET MEMO BEGIN
END
DODO
, .,
.,
"
To use the AUTO MEMORY STOP function:
1. Press the MEMORY Button (MEMO)
To turn on the MEMORY STOP function, the following
syrnbol " - " will be indicated in Ihe counter display.
2. When the VTR is placed in record a VISS signal will
be placed on the video tape.
3. Now when the video tape is rewound or fast
forwarded it will stop at the slart of any recording.
4. This function can be turned off by pressing the
MEMORY Button (MEMO).
5. Repeat playback is covered on page E-13.
MEMO
o
Press this to turn on
"MEMORY STOP:
"EW
BE]
Press either REW or FF.
The tape stops
automatically at the VISS
write point or BGN set
point.
Each time the MEMORY Button is
MEt
pressed. the mode changes in the
foHowing sequence:
·-VtSS"
Memory stop
j
1·time memory repeat
j
Continuous repeat
I
No indication (OFF)
This blinks while the VISS signal
is being written on the tape.
11 lights when VISS is set on the
menu.
Counter Reset
The counter display is reset to
"0:00:00"
when the
RESET Button is pressed. The BGN/END setting is
also set to
"0:00:00".
RESET
o
rl·nrl·rlrl
!...I· L.IL.I· L.I !...I.
Remaining Tape
"TAPE REMAIN" provides a rough indication of the
amount of tape remaining. The indication appears about
40 seconds after recording or playback has commenced
(it does not appear until this time).
TAPE REMAIN
I - - - - - I F
Tape end
Tape beginning
Each lamp going off one
after another indicates
that the tape is
approaching its end.
Note: The remaining tape indicator provides only a
rough indication:
it
is not meant to be precise.
- E-11 -
OPERATING INSTRUCTIONS
Advertisement
Chapters
Table of Contents
