Cardinal 210 Installation And Technical Manual
  1. Manuals
  2. Brands
  3. Cardinal Manuals
  4. Accessories
  5. 210
  6. Installation and technical manual

Cardinal 210 Installation And Technical Manual

Hide thumbs Also See for 210:
Table of Contents

Advertisement

Quick Links

210
WEIGHT INDICATOR
Installation and Technical Manual
PO BOX 151  WEBB CITY, MO 64870
8200-M585-O1 Rev D
Printed in USA
PH (417) 673-4631  FAX (417) 673-5001
11/14
www.cardinalscale.com
Technical Support: Ph: 866-254-8261  techsupport@cardet.com
8200-M585-O1 Rev D  210 Installation & Technical
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 210 and is the answer not in the manual?

Questions and answers

Related Manuals for Cardinal 210

Summary of Contents for Cardinal 210

  • Page 1 Installation and Technical Manual PO BOX 151  WEBB CITY, MO 64870 8200-M585-O1 Rev D Printed in USA PH (417) 673-4631  FAX (417) 673-5001 11/14 www.cardinalscale.com Technical Support: Ph: 866-254-8261  techsupport@cardet.com 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 2 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 3 Thank you for selecting and purchasing the Cardinal Model 210 Weight Indicator. The Model 210 was built with quality and reliability at our factory in Webb City, Missouri and incorporates the latest in digital technology and innovative features for the weighing industry. Configuration and upgrades can easily be performed in the field, while still maintaining the rigid control the most demanding installations require.
  • Page 4 CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR UN TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES INSTRUCTIONS. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 5: Table Of Contents

    CALIBRATION "C" NUMBERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 69 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 6 PART IDENTIFICATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 108 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 7: Specifications

    1 ea bi-directional 20mA port (uses one of the four RS-232 ports) 1 ea USB port (uses one of the four RS-232 ports) 8 ea Remote Isolated Inputs 8 ea Remote Isolated Outputs 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 8: Standard Features

    Any application affected by vibration or movement on ® the scale platform can benefit using StableSENSE 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 9: Precautions

    ALWAYS store and transport electronic printed circuit cards and components in anti-static protective bags or packaging. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 10 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 11: Site Preparation Requirements

    SITE PREPARATION REQUIREMENTS The Cardinal 210 indicator is a precision weight-measuring instrument. As with any precision instrument, they require an acceptable environment to operate at peak performance and reliability. This section is provided to assist you in obtaining such an environment.
  • Page 12 RFI (Radio Frequency Interference) in a digital weight indicator is weight indication instability during a radio transmission. Cardinal digital weight indicators are designed with special grounding and RFI shielding to achieve a high degree of immunity to common RFI. To maximize the digital weight indicator’s immunity to radio transmissions, follow these guidelines: 1.

  • Page 13: Installation

    The Model 210 Indicator is housed in a Stainless Steel wall or desk-mount enclosure. The gimbal may be mounted on a desktop or other smooth, flat, horizontal surface or may be mounted on a wall.

  • Page 14: Load Cell Cable Connection For Rfi Suppression

    If sense leads ARE used (as in motor truck scales), these plug-in jumpers should be positioned on one plug-in pin only or removed and stored for later use (see Figure No. 15). 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 15: Load Cell Cable Connection (Standard Gland Connector)

    The sense wires must be connected between the +SENS, -SENS terminals on the indicator and the +EXCITATION, -EXCITATION wires of the load cells or the +SENS, -SENS terminals of the load cell trim board or the section seal trim board. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 16: Serial I/O Cable Installation

    INSTALLATION, CONT. Serial I/O Cable Installation The 210 indicator may be connected to a printer to record weight and associated data or it may be connected to a remote display or to a computer for transmission of weight data. The weight data may be transmitted on demand (pressing the PRINT key or on receipt of a command from the computer).
  • Page 17 Interconnect Wiring for 20mA Current Loop Operation Peripheral Device has PASSIVE END of Current Loop. Figure No. 8 PORT RS-232 20mA TXD0 RXD0 TXD1 RXD1 TXD2 RXD2 TXD3 RXD3 * Mutually exclusive ** Mutually exclusive 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 18: Usb Interface And Usb Cable Installation

    INSTALLATION, CONT. USB Interface The 210 indicator USB Interface is a standard full speed (12Mbps) USB 2.0 device port. It can be connected to a USB 2.0 host, with the Cardinal Scale 8200-B163-0A USB CABLE or a industry standard USB 2.0 cable, to be used as the COM3 serial I/O port set to 8 bit data, 1 stop bit, no parity, 9600 to 115.2k baud.

  • Page 19: Main Pc Board I/O Functions Table

    The relay box cable wire numbers correspond to the indicator main PC board remote input (P3) and output (P2) terminal connection pins. CABLE WIRE RELAY NUMBER CABLE WIRE RELAY NUMBER NUMBER (Set Proper Jumpers) NUMBER (Set Proper Jumpers) +SRC (For AC Input Relays) 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 20: Optically Isolated Remote Inputs

    NOTE: The input must be momentarily connected to GND to initiate the function. AC Input Relay Board(s) The AC Input Relay Board(s) are mounted in an external junction box for use with the 210 Indicator. The RB4-ACIN (115 VAC) or RB4-ACINV (230 VAC) contain one board and supports 4 inputs (jumper selectable).
  • Page 21 Relay Box Assembly RB4-ACIN or RB8-ACIN Relay Box Assembly RB4-ACINV or RB8-ACINV Relay Box Assembly RB4-ACIN or RB8-ACIN IMPORTANT! AC INPUT RELAYS ARE VOLTAGE DEPENDENT. A DIFFERENT RELAY IS REQUIRED FOR 115 VAC AND 230 VAC! 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 22: Pwc/Checkweigher Logic Level Output

    INSTALLATION, CONT. Preset Weight Comparator/Checkweigher Logic Level Output If you so choose, you may use the logic level outputs from your Model 210 indicator’s preset weight comparators or checkweigher to control peripheral devices used to manage the flow of material or signal when the weight is within preset limits. Note that these outputs are at logic level and cannot drive external devices directly, with the exception of the Cardinal 2XX-OU Checkweigher Light Bar.

  • Page 23: Ac Output Relay Board(S)

    INSTALLATION, CONT. AC Output Relay Board(s) The AC Output Relay Boards are mounted in an external junction box for use with the 210 Indicator and can be purchased from Cardinal. The RB4-ACOUT contains one board and supports four outputs (jumper selectable). The RB8-ACOUT contains two boards and supports eight outputs.

  • Page 24: Rb4C Relay J-Box

    J4 (see Figure No. 12), one for each relay. Figure No. 12 (Relay Control Source Type Jumpers) RB4C Output Relay Wiring Example Figure No. 13 RB4C Control Circuit Wiring Example Figure No. 14 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 25: Main Pcb (Figure No. 15)

    INSTALLATION, CONT. Main PCB Figure No. 15 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 26: Main Pcb Jumpers

    Main PCB Jumpers J2 – REMOTE INPUT SRC (SOURCE) The Remote Input SRC jumper J2, when connected, allows the 210 indicator to supply (source) 12-24VDC to a solid-state relay or other load of 200 ohms or greater. The positive connection from the relays must be connected to the remote input connector pins and the negative wire from the relays to the GND/SHLD pin.

  • Page 27: Keypad Functions

    KEYPAD FUNCTIONS The Model 210 is equipped with a 22-key keypad. The keypad is used to enter commands and data into the indicator. This section describes each key along with its normal function. It is helpful to refer to the actual indicator while reading this section.
  • Page 28 ENTER key. Press the  key to abort the input operation. To exit the count function and display weight, press the NET/GROSS key. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 29 TIME/DATE KEY This key is used to enter the clock mode to program the time, date and consecutive number. Pressing the TIME/DATE key will enter the clock mode with the 210 displaying HoUr=. 12-Hour Format Selected In Setup (td=12) 1. With the display showing HoUr=, press the ENTER key.
  • Page 30 The ALrti prompt will be displayed, press the ENTER to display the number of seconds that the alarm output (PWC1) is to be turned on when the scale weight exceeds the alarm weight. The alarm time can be from 0 to 99 seconds. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 31 ENTER key.  The setup parameter oPEr=3, p out=, determines the number of preset weight comparators that will be displayed and prompted for.  There can be up to 8 Preset weight comparators. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 32 If displaying gross weight, the only weight printed is gross weight. If displaying net weight, the gross, tare, and net weights are printed. The 210 includes support for visual tickets. Visual tickets are designed by the PC based programs...
  • Page 33 Second, the ENTER key is used to signal completion of the entry of data and causes the indicator to process the data entered. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 34 2. All vertical segments and decimal points will turn on (no annunciators). 3. All annunciators will turn on. 4. All display elements off. 5. The model number (210) and the software version X.X. 6. The calibration numbers (C1 to C4).  AND PRINT KEY This combination is used to change the selected print ticket format.

  • Page 35: Annunciators

    3. Note that this annunciator is active only when the Preset Weight Comparator feature has been enabled. NOTE: PWC’s 4 thru 8 do not have display annunciators. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 36 This annunciator is located to the right of the weight display and is used to indicate that the displayed unit of weight measurement is tonnes (metric tons). 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 37: Setup And Calibration

    Print Tab Settings (starts at POrt prompt) F SPAn Fine Span Adjustment Hi rES Display high-resolution weight mode LoCoUt Key lock out function option Option Card Configuration (only displayed when option card is installed) 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 38: Setup

    0/NO or 1/YES, enter the new setting, then press the ENTER key to save it. PASS (No) PASS (Yes) Password protection is not needed. Password protection is desired. The Setup advances to the LFt= prompt next prompt will be PASS= 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 39 ENTER key to save it. Allowable values are: 0 = none 4 = oz (ounces) 1= tn (tons) 5 = kg (kilograms) 2= g (grams) 6 = tonnes (metric tons) 3 = lb (pounds) 7 = lb/oz (pounds/ounces) 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 40 ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it. trL=1 (Yes) trL=0 (No) 4% of scale capacity Full capacity (no limit) 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 41 ENTER key again to save it. Otherwise, use the numeric keys to select the format (12 or 24 hour) of the Model 210 clock operation, then press the ENTER key to save it. Note that in the 24 hour format, 12 is added to all times after noon, i.e. 3 PM would be 1500.
  • Page 42 ENTER key to save it. Otherwise, use the numeric keys to enter the new Scale ID and then press the ENTER key to save the new setting. Allowable values are: 0 through 99. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 43: Analog To Digital Filtering

    REMOTE, then both indicators MUST have Rev 2.6.3 or greater software installed. If a combination of 200, 205, 210 or 215 and a 225 indicator are to be used in a LOCAL/REMOTE configuration, then the remote 200, 205, 210 or 215 indicator MUST have Rev 2.6.1 or greater software installed, and the 225 indicator MUST...
  • Page 44 If the displayed value is acceptable, press the ENTER key to save it. Otherwise, use the numeric keys to enter a new value and press the ENTER key to save the new setting. Allowable values for the stable count are: 3 through 255. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 45 3. F= FILTER SETTING (1 to 99) determination: Set to desired results. 4. If stability is unacceptable with any setting of F=, reduce the sample rate and/or increase the break range, b= setting for increased filtering. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 46 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 47: Calibration

    CAL1= setting, otherwise press the ENTER key to advance to the Sio menu. CALIBRATION MODES The 210 indicator has five modes that can be used to perform calibration. Three of the modes require a test load or test weights, one requires the scale to be empty (and at zero) and the last uses the calibration “C”...
  • Page 48  Starting at the left and advancing right, a series of dashes will appear on the display. The dashes will stay on the display momentarily, then disappear, after which the display will show: Sio?. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 49 The display will show CAL2=0. This is the second of two calibration steps.  Remove the weights on the scale platform, and then press the ZERO key.  The display will advance to Sio?. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 50 NOTE: If any components have been changed that affect calibration and/or your scale is used in a commercial application and must be "Legal for Trade" you cannot use the “C” numbers to re-calibrate. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 51: Setup Guardian Scale

    If you selected id=1 (Yes, ID Prompt), an additional prompt, "a clr=" will be displayed. If you selected id=0 (No ID Prompt) proceed to A-d (A-d?) Analog to Digital Filtering. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 52: Digital Fill Control

    No trim weight adjustment will be made at the completion of a filling operation. APrnt= (Automatic Print) YES The time, date, and weight will be automatically printed at the conclusion of the fill. No automatic print at the conclusion of the fill. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 53 Filling parameters may be stored and recalled by entering an ID No Fill control storage. h oUt= (High State Before Cutoff) If the comparator outputs are to be High before cutoff, answer YES to this prompt. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 54: Preset Weight Comparator

    0/NO or 1/YES, enter the new setting, then press the ENTER key to save it. A clr=1 (Yes) a clr=0 (No) Automatically clears the ID after the ID is not cleared when ticket prints ticket has printed. and can be used for next transaction. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 55 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it. A clr=1 (Yes) a clr=0 (No) Automatically clears the ID after the ID is not cleared when ticket prints ticket has printed. and can be used for next transaction. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 56: Axle Weigher

    So the first weight will be a gross weight, all remaining axles will be in net weight. If using axle pads all weights will be gross weight. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 57 The Total Delay is the (duration in seconds for a total print to occur after the stop delay timer has expired). Allowable values for the total delay are 1 to 99 seconds. NOTE: The Total Delay timer will start after the Stoplight Delay timer expires. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 58: Livestock Weigher

    Prints the average animal weight if there’s a stored head count  CrLF= Select YES to append a LF to each printed line  EoP= Number of new lines to append at the end of a ticket 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 59: Serial Input/Output

    No Continuous Output If Cont0= YES (Continuous Output) is selected, an additional prompt, tYPE0= will be displayed. If Cont0= no (No Continuous Output) is selected, proceed to the Weight On Demand section. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 60 CZ = center of zero MO = motion ee = weight not currently being displayed cr = Carriage Return (hex 0D)  The SB-80, SB-300 (multiple displays not supported) and WinVRS use the SB-400 format. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 61 Where: stx = Start of TeXt (hex 02) swa =, swb=, swc= Status Bytes xxxxxx= Displayed Weight, Gross or Net Weight (Six Digits) cr = Carriage Return (hex 0D) sum= Checksum Character 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 62 If there is no decimal point, then the first character is a space. Leading zero blanking applies. Status = Provides information on the weight reading. The characters G/N/U/O/M/E represent Gross/Net/Underload/Overload/Motion/Error respectively. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 63 SETUP AND CALIBRATION, CONT. Weight On Demand If continuous output has not been selected for Serial Port 0 (Cont0=NO), the 210 indicator will respond to a weight request (ENQ). The host device (computer) sends: ENQ - (hex 05) The 210 will respond: <s><xxxxxx><d><uu><m><cc><cr>...
  • Page 64 14 = 14.4k Baud 19 = 19.2k Baud 28 = 28.8k Baud 38 = 38.4k Baud 57 = 57.6k Baud 76 = 76.8k Baud 11 = 115.2k Baud 23 = 230.4k Baud 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 65 ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it. tShort= YES tShort= no Toledo Short Output Format Toledo Long Output Format 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 66 No Continuous Output If Cont3= YES (Continuous Output) is selected, an additional prompt, tYPE3= will be displayed. If Cont3= no (No Continuous Output) is selected, proceed to the Weight On Demand section. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 67 RED light will turn on.  NOTE: If you enter a zero (0) for the threshold weight (THRS=0), the traffic light feature will be disabled (turned off). 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 68 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 69: Print Tab Settings

    Press the ENTER key to show the current setting for the location of Tare weight printing. If the setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the numeric keys to enter a new location and then press ENTER to save it. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 70 ENTER key to save it. Otherwise, use the numeric keys to enter the new the number of End-Of-Print linefeeds, then press the ENTER key to save the new setting. Allowable values are: 0 through 99. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 71: Fine Span Adjustment

    – Option Card Configuration This prompt will ONLY be displayed when a 2XX Option Card is installed in the indicator. Refer to the manual for the 2XX option card installed for setup instructions. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 72 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 73: Setup Review

    SETUP REVIEW The 210 indicator allows several operational parameters to be reviewed and changed without breaking the calibration seal. These operational parameters are: Power Up Zero Reset Enable/Disable Time Format Sleep Mode Feature Enable/Disable Auto Shutoff Feature Enable/Disable Serial Input / Output Configuration...
  • Page 74 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 75: Calibration "C" Numbers

    NOTE: If any components have been changed that affect calibration and/or your scale is used in a commercial application and must be "Legal for Trade" you cannot use "C" numbers to re-calibrate. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 76 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 77: Accumulators

    2. The indicator will return to normal operation when printing has been completed. To clear (zero) the Count accumulator: 1. Press the  key, the COUNT/SAMPLE key, then the ZERO key 2. Press the  key to return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 78 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 79: Troubleshooting

    TROUBLESHOOTING Error Codes The 210 indicator is equipped with software that indicates when an error in the operation takes place. The following lists the error codes displayed by the 210 along with their meaning. Should you encounter an error code, please refer to this list for the cause.
  • Page 80 UNITS key pressed in an attempt to perform a unit conversion where the interval would have been greater than 50. CORRECTIVE ACTION: Determine the reason for the error display and take the appropriate corrective action. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 81 Error Codes, Cont. UnStb (Unstable) Motion is present when trying to perform a print function. CORRECTIVE ACTION: Wait for a stable weight display (STABLE annunciator on) before performing any of this operation. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 82: Before You Call Service

    TROUBLESHOOTING, CONT. Before You Call For Service The 210 has been designed to provide you with years of trouble-free operation. However, should you experience a problem, please refer to the troubleshooting guide below before you call for service. The following describes several types of symptoms along with suggested remedies.

  • Page 83: Diagnostic Test Mode

    IMPORTANT! Once Diagnostic Test Mode has been enabled, the indicator will power on with TEST on the display. Operator must press ENTER key to stay in Diagnostic Test Mode or press  key to disable Diagnostic Test Mode. 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 84: Calibration Seal Installation

    CALIBRATION SEAL INSTALLATION If your Model 210 Weight Indicator is used in a commercial application it must be tested and sealed by your local weights and measurements official. The 210 is designed to accept a lead and wire security seal to prevent unauthorized access to the calibration adjustments. Refer to Figure No.

  • Page 85: Id Storage Operation

    ENTER key. The alarm time may be from 0 to 99 seconds. NOTE: If the alarm time setting is zero, then the alarm is disabled. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 86 7. If the number of loads is correct, press the ENTER key to save it. Otherwise, using the numeric keys enter the new number of loads and then press the ENTER key to save it. 8. The indicator will return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 87 3. The PrtALL prompt will be displayed, to print all of the IDs press the 1/YES key. The IDs and their associated tare, accumulator, and loads will be printed. NOTE: To abort the print operation, press the 0/NO key. 4. The indicator will return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 88 ACCUMULATOR= 0 lb NO OF LOADS=1 ID= 7 STORED WGHT= 100 lb K ACCUMULATOR= 0 lb NO OF LOADS=0 ID= 8 STORED WGHT= 100 lb K ACCUMULATOR= 0 lb NO OF LOADS=0 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 89 IN-PROCESS (Temporary ID) REPORT ID= 11 WEIGHT= 9242 lb ID= A WEIGHT= 9242 lb ID= D WEIGHT= 9242 lb ID= G WEIGHT= 9242 lb ID= J WEIGHT= 9242 lb ID= M WEIGHT= 9242 lb 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 90 5. The Net weight will be added to the accumulator and the number of loads will be incremented for the entered ID and the ticket printed will show the TIME, DATE, ID, and TIME/DATE of Stored Tare weight, the Gross, Tare, and Net weights. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 91 2. Press the ENTER key. The display will change to show no. 3. Press the 1/YES key.. The display will change to show YES. 4. Press the ENTER key. 5. ALL temporary ID’s are deleted. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 92 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 93: Digital Fill Control Mode Operation

    If AdiSC=No, the indicator will halt after filling and will wait for the DUMP key to be pressed (or a remote manual dump command) before the material is discharged and the next fill started. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 94 If this value is acceptable press the ENTER key, otherwise, use the numeric keys to enter a new zero tolerance weight and press the ENTER key. The current Gross/Net weight will be displayed. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 95 (PWC3 annunciator and output control are turned on). The weight display will change from net to gross. The discharge will continue until the scale weight returns to zero within the 0TOL=XX value. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 96 6. To continue the fill, press the 1/YES key or the optional START pushbutton. 7. The 210 will return to normal operation, displaying the Gross weight on the scale. NOTE: If dGAtE=YES, the fill operation cannot be restarted after a STOP if the material weight is above the zero tolerance.
  • Page 97 ENTER key, otherwise, use the numeric keys to enter a new time and press the ENTER key. The valid range is 0.00 to 99.9 seconds. The current Gross/Net weight will be displayed. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 98 (PWC3 annunciator and output control are turned on). The weight display will change from net to gross. The discharge will continue until the scale weight returns to zero within the 0 TOL=XX value 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 99 6. To continue the fill, press the 1/YES key or the optional START pushbutton. 7. The 210 will return to normal operation, displaying the Gross weight on the scale. NOTE: If dGAtE=YES, the fill operation cannot be restarted after a STOP if the material weight is above the zero tolerance.
  • Page 100 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 101: Digital Fill Control Id Storage

    9. If a zero value is correct, press the ENTER key to save it. Otherwise, using the numeric keys enter the number of batches and then press the ENTER key to save it. 10. The indicator will return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 102 9. If the count is correct, press the ENTER key to save it. Otherwise, using the numeric keys to enter a new count value and then press the ENTER key to save it. 10. The indicator will return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 103 3. The PrtALL prompt will be displayed, to print all of the IDs press the 1/YES key. The IDs and their associated settings will be printed. NOTE: To abort the print operation, press the 0/NO key. 4. The indicator will return to normal operation. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 104 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 105: Axle Weigher Operation Mode

    The example below illustrates a typical print ticket for a five-axle truck. Time 13:47 09-26-12 Date 15440 lb 16320 lb 15980 lb Axle Weights 15880 lb 15700 lb Total 79320 lb Total Vehicle Weight Axle Numbers 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 106 Note, however, that as soon as the first axle of the next vehicle is printed, the weights from the previously weighed vehicle are cleared. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 107 These outputs can be used, or the serial output of the indicator can contain the light state information if continuous data type = 8 (tyPE#=8, where # is the serial port number). 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 108 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 109: Livestock Weigher Mode Operation

    3. Press the PRINT key. 4. Total ticket will be printed containing total weight, total head count, and average weight. 5. These values will be reset after the total ticket is printed. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 110 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 111: Model 210Dc

    Connect the negative (-) voltage source wire to the terminal marked GND on the terminal block as shown in Figure No. 20 below. The indicator can be operated as described in this manual. Positive Wire Negative Wire Figure No. 20 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 112: Local/Remote Setup

    In addition, the Continuous Output must be set to NO (Cont=no). Local/Remote 210 RS-232 Wiring REMOTE 210 LOCAL 210 Figure No. 21 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 113 LOCAL/REMOTE SETUP, CONT. Local/Remote 210 20mA Current Loop Wiring Figure No. 22 8200-M585-O1 Rev D  210 Installation & Technical...

  • Page 114: Part Identification

    LABEL – HIGH VOLTAGE 8200-B392-0A CABLE: AC POWER W/FILTER 205/210 DWI (US) 8539-B254-0A ASSEMBLY: CABLE, CALIBRATION SWITCH 6980-0250 POWER CORD H05VV-F3G 1mm, 10A/250V, BLACK 6610-1506 GLAND CONN. NICKEL 3502-B217-0A HOLE PLUG, ASSEMBLY 1-1/8” DIA. S.S. 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 115 PART IDENTIFICATION, CONT. (Rear Enclosure Sub Assembly) 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 116 PART IDENTIFICATION, CONT. (Rear Enclosure Sub Assembly) 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 117 TAPE DBL SIDED 1.0 WIDE 45 MIL THK. 8200-B014-08 GASKET FOR 210 ENCLOSURE 8200-C015-0A WELDMENT: BEZEL FOR 210 8200-C017-0A WELDMENT: ENCLOSURE, FRONT 8200-C210-OA DAC PCB (OPTIONAL) 8200-D124-1A PC BD, ASSY. 210 MAIN 8200-D202-08 KEYPAD: 210 DWI 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 118 8200-D208-0A SUB ASSEMBLY: FRONT (210) 8200-D208-2A SUB ASSEMBLY: FRONT (210-A) 8200-D207-1A SUB ASSEMBLY: REAR ENCLOSURE (210EU) 8200-C247-0A SUB ASSEMBLY: REAR ENCLOSURE (210DC) 8200-D208-5A SUB ASSEMBLY: FRONT (210DC) 8200-D208-9A SUB ASSEMBLY: FRONT (210EU) 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 119 STATEMENT OF LIMITED WARRANTY WARRANTY TERMS Cardinal Scale Manufacturing Company warrants the equipment we manufacture against defects in material and workmanship. The length and terms and conditions of these warranties vary with the type of product and are summarized below:...
  • Page 120 This warranty sets forth the extent of our liability for breach of any warranty or deficiency in connection with the sale or use of our product. Cardinal will not be liable for consequential damages of any nature, including but not limited to loss of profit, delays or expenses, whether based on tort or contract.
  • Page 121 8200-M585-O1 Rev D  210 Installation & Technical...
  • Page 122 8200-M585-O1 Rev D  210 Installation & Technical...

Table of Contents

Save PDF