Table of Contents
Advertisement
FastMig Pulse
350, 450
Operating manual
Brugsanvisning
Gebrauchsanweisung
Manual de instrucciones
Käyttöohje
Manuel d'utilisation
Manuale d'uso
Gebruiksaanwijzing
Bruksanvisning
Instrukcja obsługi
Manual de utilização
Инструкции по эксплуатации
Bruksanvisning
操作手册
EN
DA
DE
ES
FI
FR
IT
NL
NO
PL
PT
RU
SV
ZH
Advertisement
Table of Contents
Related Manuals for Kemppi FastMig Pulse 350
Summary of Contents for Kemppi FastMig Pulse 350
- Page 1 FastMig Pulse 350, 450 Operating manual Brugsanvisning Gebrauchsanweisung Manual de instrucciones Käyttöohje Manuel d’utilisation Manuale d’uso Gebruiksaanwijzing Bruksanvisning Instrukcja obsługi Manual de utilização Инструкции по эксплуатации Bruksanvisning 操作手册...
- Page 3 OPERATING MANUAL English...
-
Page 4: Table Of Contents
................... . FastMig Pulse 350, 450... -
Page 5: Introduction
This operating manual contains important information on the use, maintenance and safety of your Kemppi product. The technical specifications of the equipment can be found at the end of the manual. Please read the operating manual and the safety instructions booklet carefully before using the equipment for the first time. -
Page 6: Installation
It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment is connected only to a supply with a short-circuit power S greater than or equal to 5.5 MVA. FastMig Pulse 350, 450... -
Page 7: Machine Introduction
The machine is not allowed to be operated in the rain as the protection class of the machine, IP23S, allows preserving and storing outside only. Never aim the spray of sparks from a grinding machine toward the equipment. NOTE! © Kemppi Oy / 1515... -
Page 8: Connecting Cables
2.5.1 Liquid cooled system: FastMig Pulse + MXF + FastCool 10 MXF wire feed unit FastMig Pulse power source FastCool liquid cooler and power connection Gas supply MMA electrode holder Remote control device Liquid cooled welding Gun Power cable Earth return lead and clamp FastMig Pulse 350, 450... -
Page 9: Air Cooled System: Fastmig Pulse + Mxf
2.5.3 Connecting to mains power FastMig power sources are delivered as standard with 5 meters of mains power cable. No mains plug is fitted at the Kemppi factory. If local country based regulations state an alternative power cable is required, the mains NOTE! cable must be replaced in conformity with the regulations. -
Page 10: Welding And Earth Return Cables
2.5.4 Welding and earth return cables Kemppi always recommend the use of high quality copper cables with a suitable cross- sectional area. Cable size should be selected depending on the intended welding application. 50mm2 copper welding cables may be used for low duty work in basic or Synergic 1-MIG. -
Page 11: Operation Control
Pulse equipment, and therefore can be activated by purchasing the appropriate licence for the MMA process. Please see ordering number codes. FastMig Pulse power source will not support the MMA process without an MXF wire feeder connected. © Kemppi Oy / 1515... -
Page 12: Control Panel P 65
This button takes you to the main menu list. Proceed following the instructions on screen. P 65 main menu list Edit Channel Make changes to existing welding channel User Identification Select one user out of ten FastMig Pulse 350, 450... -
Page 13: Using The Menus
Up to 10 user profiles can be defined in one FastMig Pulse unit, and each of them are assigned up to 10 memory channels. So, you have maximum of 100 memory channels to store your frequently used welding jobs. In addition to them, there are 10 memory channels available for MMA use. © Kemppi Oy / 1515... -
Page 14: Creating The First Memory Channel
When you have created a memory channel, the system is ready to weld. You select the desired memory channel number on wire feeder's control panel, set the welding power and arc length and start welding. FastMig Pulse 350, 450... -
Page 15: Welding Parameters And Functions
The higher the value the rougher the arc is. Pulse Current -10% ... +15% Factory Setting Reduces the pulse current of the curve at the maximum is 0% 10% and raises it at the maximum 15%. © Kemppi Oy / 1515... - Page 16 Controls the short circuit behaviour of the arc. The lower the value the softer the arc is. The higher the value the rougher the arc is. StartPower -9 ... +9 Factory setting is 0 Adjusts arc ignition FastMig Pulse 350, 450...
-
Page 17: Welding Functions
Set the level of the curve where the crater filling will start. CraterFillEnd 10 – 250%, not 1 % steps. Factory setting 30% higher than start CraterTime 0.0 – 10.0 s 0.1 s steps. Factory setting 1. 0 s © Kemppi Oy / 1515... - Page 18 System Device information: Information DevSW: Unit Software Version. SysSW: System Software Version (Base software version). BootSW: Boot Software Version. SW Item: Software Item Number (IFS number). Serial: Device Serial number. Prog: Programmer name Date: Programming date. FastMig Pulse 350, 450...
- Page 19 OFF: Remote control units are not recognized. Remote device selection remains unchanged if the selected remote control unit disappears MIG CurrentDisp ON / OFF Factory Setting: OFF ON: Display’s amperage (A) preset values OFF: Display’s wire feed speed m/min. © Kemppi Oy / 1515...
-
Page 20: Welding Software Delivery Profile
9991014 5. MatchLog 9991017 Kemppi DataStore offers new welding software packages and special enhanced arc performance solutions. Customization of FastMig Pulse systems can make welding more efficient. Solutions offered are designed to meet the needs of wide ranging welding environments. - Page 21 Wire ø (mm) Shielding gas Process Number Ar+15–25%CO₂ 1-MIG Ar+15–25%CO₂ 1-MIG Ar+15–25%CO₂ 1-MIG Ar+15–25%CO₂ 1-MIG CO₂ 1-MIG CO₂ 1-MIG CO₂ 1-MIG CO₂ 1-MIG Fe Metal Ar+15–25%CO₂ 1-MIG Fe Metal CO₂ 1-MIG Fe Rutil Ar+15–25%CO₂ 1-MIG Fe Rutil CO₂ 1-MIG © Kemppi Oy / 1515...
- Page 22 CrNiMo 19 12 Ar+2%CO₂ 1-MIG CrNiMo 19 12 Ar+2%CO₂ 1-MIG FC-CrNiMo 19 12 Ar+15–25%CO₂ 1-MIG More welding programs are available by purchasing MatchCurve and MatchCustom products. You can also order welding program packs together with WiseFusion function. FastMig Pulse 350, 450...
-
Page 23: Basic Troubleshooting
Check power supply – 3 x phase present? Many of these checks may be carried out by the operator. However certain checks relating to NOTE! mains power must be completed by an authorised trained electrician. © Kemppi Oy / 1515... -
Page 24: Operation Disturbances
Should you experience a malfunction from your machine, please consult the basic troubleshooting text above first, and complete some basic checks. If the machine malfunction cannot be corrected with these measures, contact your KEMPPI maintenance service workshop. Operation of the overload protection Yellow thermal protection lamp is lit when the thermostat is operating due to loading beyond the stated duty cycle. -
Page 25: Periodic Maintenance
• Operation and performance values of the machine are checked, and when necessary adjusted by means of software and test equipment. Software loading Kemppi Service Workshops can also test and load firm ware and welding software. DISPOSAL OF THE MACHINE Do not dispose of electrical equipment with normal waste! -
Page 26: Ordering Numbers
ORDERING NUMBERS FastMig Pulse 350 power source P 65 control panel included 6150400 FastMig Pulse 450 power source P 65 control panel included 6150500 FastMig Pulse 350 power source No control panel 6150400C1 FastMig Pulse 450 power source No control panel... - Page 27 SuperSnake GT02S sub feeder synchronization W004030 unit for FastMig MXF wire feed units WiseFusion welding function 9991014 WisePenetration welding function 9991000 WiseRoot welding process 6265011 WiseThin welding process 9991013 MatchLog 9991017 MMA welding process 9991016 © Kemppi Oy / 1515...
-
Page 28: Technical Data
50 V DC / 100 W 50 V DC / 100 W Fuse (delayed) 6.3 A 6.3 A Voltage supply for cooling unit 24V DC / 50 VA 24V DC / 50 VA * See paragraph 2.2. FastMig Pulse 350, 450... - Page 30 Telefax +91-44-4567 1234 Tel. +61 2 9605 9500 Literbuen 11 sales.india@kemppi.com Telefax +61 2 9605 5999 DK-2740 SKOVLUNDE info.au@kemppi.com KEMPPI WELDING SOLUTIONS SDN BHD DANMARK Tel +45 4494 1677 No 12A, Jalan TP5A, OOO KEMPPI Telefax +45 4494 1536 Taman Perindustrian UEP, Polkovaya str.