Subscribe to Our Youtube Channel
Related Manuals for Nexcom VTC 1010
Summary of Contents for Nexcom VTC 1010
- Page 1 NEXCOM International Co., Ltd. Mobile Computing Solutions Vehicle Telematics Computer VTC 1010 User Manual NEXCOM International Co., Ltd. www.nexcom.com Published October 2015...
-
Page 2: Table Of Contents
LED Indicators (PWR, Status, LAN & GPIO) ..........6 WWAN Module Selector (For Wake-Up & Voice on CN10) ....20 LED Indicators (SSD, GPS, WLAN & WWAN) .........6 RTC Battery Connector ..............20 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 3 Chapter 5: System Setup RS232 Connector ................56 Removing the Chassis Cover ..............37 GPIO + CAN Bus 2.0B Connector ............57 Installing the First WWAN Module ............38 OBDII Connector ................57 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
- Page 4 Appendix E: Vehicle Power Management Setup External Power Output Setting ..............67 Startup and Shutdown Voltage Setting ..........67 Power-on Delay Setting .................69 Power-off Delay Setting ................71 Appendix F: Power Consumption......73 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 5: Preface
Acknowledgements The product(s) described in this manual complies with all applicable VTC 1010 is a trademark of NEXCOM International Co., Ltd. All other European Union (CE) directives if it has a CE marking. For computer systems product names mentioned herein are registered trademarks of their to remain CE compliant, only CE-compliant parts may be used. -
Page 6: Rohs Compliance
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm. In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products. The task force will ensure that we follow the standard... -
Page 7: Warranty And Rma
▪ Replace with 3rd party products if needed. ▪ Customers must collect all the information about the problems ▪ If RMA goods can not be repaired, NEXCOM will return it to the customer encountered and note anything abnormal or, print out any on-screen without any charge. - Page 8 There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. viii Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
- Page 9 ▪ The computer is provided with CD drives that comply with the appropriate ▪ All cautions and warnings on the equipment should be noted. safety standards including IEC 60825. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 10: Technical Support And Assistance
Preface Technical Support and Assistance Conventions Used in this Manual 1. For the most updated information of NEXCOM products, visit NEXCOM’s Warning: website at www.nexcom.com. Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself 2. -
Page 11: Global Service Contact Information
13F, No.920, Chung-Cheng Rd., ZhongHe District, Beijing, 100094, China New Taipei City, 23586, Taiwan, R.O.C. Tel: +86-010-5704-2680 Tel: +886-2-8226-7796 Fax: +86-010-5704-2681 Fax: +886-2-8226-7792 Email: sales@nexcom.cn Email: sales@nexcom.com.tw www.nexcom.cn www.nexcom.com.tw Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 12 Wuhan, 430070, China Building 11, 599 Yunling Road, Putuo District, Shanghai, 200062, China Tel: +86-27-8722-7400 Tel: +86-21-6125-8282 Fax: +86-27-8722-7400 Fax: +86-21-6125-8281 Email: sales@nexcom.cn Email: frankyang@nexcom.cn www.nexcom.cn www.nexcom.cn Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 13: Package Contents
Preface Package Contents Before continuing, verify that the VTC 1010 series package that you received is complete. Your VTC 1010 series package should have all the items listed in the following table. Item Name Specification 4NCPM00302X00 (T)Terminal Blocks 3P Phoenix Contact:1777992 5.08mm Male DIP Green... - Page 14 Intel Atom™ processor E3827 1.75GHz CPU, 2GB DDR3L SO-DIMM, ® VGA/DP Output, 1x LAN, 2x RS-232, 1x RS-422/485, 3x DI, 3x DO, 3x USB, 12VDC output Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 15: Chapter 1: Product Introduction
(WWAN Voice) slot cover Reset button Multi Port Mic-in USB 2.0 LAN DC input COM1 Antenna hole 9V~36V LED indicators USB 3.0 Event Button Antenna holes Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 16: Overview
• 4x Mini-PCIe expansions non-working vehicle. With dual SIM card design, it allows the choice of the best service carrier network and minimizes roaming cost. VTC 1010 • Wake on RTC/SMS via WWAN module can be configured to work with two independent WWAN connections and • Compliant with MIL-STD-810G... -
Page 17: Hardware Specifications
▪ Selectable boot-up & shut-down voltage for low power protection by ▪ 1x reset button software ▪ 1x type A USB 3.0 compliant host, supporting system boot up. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 18 Storage: MIL-STD-810G, Method 514.6, Category 24, minimum integrity test ▪ Shock (SSD): Operating: MIL-STD-810G, Method 516.6, Procedure I, functional shock=20g Non-Operating: MIL-STD-810G, Method 516.6, Procedure V, crash hazard shock test=75g Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 19: Connector Numbering
The following diagrams indicate the numbers of the connectors. Use these numbers to locate the connectors’ respective pinout assignments on chapter 2 of the manual. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 20: Chapter 2: External Connectors Pinout Description
LED2 (LAN) Blinking: Active LED4 (SSD) Green: Storage access Steady Green: System ready LED3 (HEALTH) Steady Red: System booting Blue: Power good LED4 (POWER) Red: Power failure Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 21: Usb 3.0 Port
USB 3.0 Port Audio Jack 3.5mm Connector Number: 3 Connector Number: 4 Definition Definition Definition Definition USB_N MIC-C1 USB_P FRONT_RC1 FRONT_LC1 USB3_RXN USB3_RXP CON DET USB3_TXN USB3_TXP Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 22: Sd Card Connector
Chapter 2: External Connectors Pinout Description SD Card Connector SIM1 Socket Connector Number: 5 Connector Number: 5 Definition Definition Definition Definition UIM1_PWR2 UIM1_RST2 UIM1_CLK2 UIM1_DAT2 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 23: Sim2 Socket
Chapter 2: External Connectors Pinout Description SIM2 Socket Event Button Connector Number: 5 Connector Number: 6 Definition Definition Definition UIM2_PWR2 Front Event UIM2_RST2 UIM2_CLK2 UIM2_DAT2 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 24: Reset Button
Chapter 2: External Connectors Pinout Description Reset Button Power Input Connector Number: 7 Connector Number: 8 Definition Definition 1-2 Open NORMAL GND_IN 1-2 Short RESET# V_IN IGNITION Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 25: Multiport Connector
ISO_GND CAN_M_L 1PPS RS422_TX- ISO_GND CAN_M_H CAP2_B RS422_TX+ GPIO3 REAR_PANIC CAP1_A AGND GPIO4 AGND CAP1_B FRONT_L_C SP_RXD_3 SURR_OUT_L_C SP_RTS_3 FRONT_R_C SP_DCD_3 SURR_OUT_R_C SP_RI_3 FRONT_JD OUT_12V SURR_JD Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 26: Vga Connector
Connector size: DB15, Female Connector size: DB9, Male Connector Number: 10 Connector Number: 11 Definition Definition Definition Definition Green Blue Red_RTN Green_RTN Blue_RTN I2C_Data H SYNC V SYNC I2C_CLK Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 27: Line-Out
Chapter 2: External Connectors Pinout Description Line-out Mic-in Connector Number: 12 Connector Number: 13 Definition Definition Definition Definition Mic1 C Mic2 JD Line2 LC Line2 JD Mic1 CL Line2 RC Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 28: Displayport
Connector Number: 14 Connector Number: 15 Definition Definition Definition Definition DP0_DATA0_P USB_N DP0_DATA0_N DP0_DATA1_P USB_P DP0_DATA1_N DP0_DATA2_P DP0_DATA2_N DP0_DATA3_P DP0_DATA3_N CONFIG1 CONFIG2 DPC0_AUXP_C DPC0_AUXN_C RETURN DP0_PWR Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 29: Lan Connector
Chapter 2: External Connectors Pinout Description LAN Connector Connector Number: 16 Definition Definition MDI0P MDI0N MDI1P MDI2P MDI2N MDI1N MDI3P MDI3N LED1- LED1+ LED2- LED2+ Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 30: Chapter 3: Jumpers And Switches
Chapter 3: Jumpers and Switches This chapter describes how to set the jumpers on the motherboard. Note dry environments. A grounding strap is warranted whenever danger of that the following procedures are generic for all VTC 1010 series. static electricity exists. Before You Begin Precautions ▪... -
Page 31: Jumper Settings
(on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right) Three-Pin Jumpers: Pins 1 and 2 are Short Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 32 Chapter 3: Jumpers and Switches VTC 1010 Connector Specification & Jumper Setting VTC 1010 carrier board placement The figure below is the carrier board used in the VTC 1010 system. It shows the locations of the jumpers and connectors. Top View Bottom View...
-
Page 33: Vtc 1010 Jumper And Switch Settings
SW2.2 SW6.2 Note: Once CMOS is cleared and the power connector is plugged in, VTC 1010 will power on and power off automatically in the first Power-On. After first Power-On, VTC 1010 will work normally. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. -
Page 34: Wwan Module Selector (For Wake-Up & Voice On Cn10)
Wake-Up & Voice Wake-Up & Voice MC8090/8092 SW7.1 RTC_BAT SW7.2 Digital Voice* HE910 (I2S) Disabled (default) MC8090(PCM) Default Settings: SW7.1 SW7.2 *Digital voice is selectable in BIOS. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 35: External Thermal Sensor Module
Connector size: 1 x 10 = 10-pin header (1.0mm) Connector location: JP7 Connector location: J15 Definition Definition Definition Sensor PCIRST# Sensor 33M_CLK LPC_FRAME# LPC_AD3 LPC_AD2 LPC_AD1 LPC_AD0 VCC3 VCC3 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 36: Vga Connector
Connector size: 1 x 10 = 10-pin header (1.0mm) Connector location: J6 Connector location: CN7 Definition Definition Definition Definition VGA +5V VGA_CLK VGA_DATA VGA_VS VGA_HS VGA_GND VGA_BLUE VGA_GND VGA_GREEN VGA_GND VGA_RED M_DET Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 37: High Speed Uart Connector
Connector location: CN15 Definition Definition SIO_RTS_1 Definition Definition SIO_TXD_1 SIO_CTS_1 CAN2.0B_H CAN_1939_H SIO_RXD_1 CAN2.0B_L CAN_1939_L SIO_CTS_0 SIO_RXD_0 SIO_RTS_0 SIO_TXD_0 ANALOG-Input1 ANALOG-Input2 ANALOG-Input3 ANALOG-GND Definition Definition CAN_DI1 CAN_DO1 CAN_M_VCC5 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 38: Capture Card Connector
Connector size: 2 x 5 = 10-pin header (1.27mm) Connector location: J5 Connector location: JP10 Definition Definition Definition Definition CAP2_B CAP1_A CAP1_B CAP2_A CAP1_B CAP2_A CAP2_B CAP1_A Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 39: 5V Output
Connector size: 1 x 2 = 2-pin header (1.25mm) Connector size: 1 x 2 = 2-pin header (1.25mm) Connector location: J21 Connector location: J10 Definition Definition FRONT_EVENT Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 40: Sata Hdd Connector
CN14, 1 x 7 = 7-pin header (1.27mm) Connector location: JP6 Connector location: CN11 & CN14 CN11 Definition Definition Definition VCC12 VCC5 CN14 Definition Definition SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 41: Gal Download Port
Connector size: 1 x 6 = 6-pin header (2.54mm) Connector size: 1 x 5 = 5-pin header (2.54mm) Connector location: JP8 Connector location: JP9 Definition Definition Definition Definition VCC3 V3.3ALW MRST C2CK Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 42: Gpio Setting
Don’t care SW1.6 Pull up VCC5 Don’t care Power Range (9~36V) SW1.7 SW3.1 SW1.8 SW3.2 Don’t Care Default Settings: SW1.1 SW1.2 SW1.3 SW1.4 SW1.5 SW1.6 SW1.7 SW1.8 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 43: Fan Connector
Connector size: 1 x 4 = 4-pin header Connector size: 1 x 4 = 4-pin header Connector location: J9 Connector location: J13 Definition Definition Definition Definition Power IPPS FAN_TACT FAN_CTRL ODOMETER DIRECTION Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 44: Gps Module Connector
Connector size: 1 x 6 = 6-pin header Connector location: J14 Connector location: J12 Definition Definition Definition Definition GPS_BAT GPS_LED MCU GPO2 GPS_CTX GPS_CRX MCU GPO1 MCU GPI2 VCC3_GPS MCU GPI1 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 45: Pcie Connector
Connector size: 1 x 6 = 6-pin header Connector location: J19 Connector location: J20 Definition Definition Definition Definition PCIE_CLKN PCIE_CLKP 12VSB PCIE_RXN PCIE_RXP 12VSB 12VSB PCIE_TXN PCIE_TXP USBHUB_3N USBHUB_3P PLTRST EXP_Disable Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 46: Mini-Pcie (Usb + Pcie)
Definition Definition WAKE# +V3.3A_MINI1 +V1.5S_MINI1 SMBCLK +V1.5S_MINI1 PCIE_TX_N SMBDAT CLK_REQ# PCIE_TX_P USB- PCIE_CLK# USB+ PCIE_CLK +V3.3A_MINI1 +V3.3A_MINI1 WLAN_LED# WLAN_DIS# RESET# +V1.5S_MINI1 PCIE_RX_N +V3.3A_MINI1 PCIE_RX_P BT_EN +V3.3A_MINI1 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 47: Mini-Pcie (Msata Or Pcie [Default])
Definition Definition WAKE# +V3.3_MINI_3 +V1.5S_MINI_3 SMBCLK +V1.5S_MINI_3 SATA_TXN0_C SMBDAT CLKREQ SATA_TXP0_C USB_D- REFCLK- USB_D+ REFCLK+ +V3.3_MINI_3 +V3.3_MINI_3 WWAN_LED# MINICARD3_DIS# WLAN_RESET# +V1.5S_MINI_3 SATA_RXP0_C +V3.3_MINI_3 SATA_RXN0_C CTRL0 +V3.3_MINI_3 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 48: Mini-Pcie (Usb + Pcie)
+V3.3A_MINI_2 +V1.5S_MINI_2 SMBCLK +V1.5S_MINI_2 PCIE_TX_N2 SMBDAT CLK_REQ#2 UIM2_PWR2_MINI PCIE_TX_P2 UIM2_DAT2_MINI USB- PCIE_CLK#2 UIM2_CLK2_MINI USB+ PCIE_CLK2 UIM2_RST2_MINI +V3.3A_MINI_2 +V3.3A_MINI_2 PCIE2_LED PCIE2_DIS# PCIE2_RST# +V1.5S_MINI_2 PCIE_RX_N2 +V3.3A_MINI_2 PCIE_RX_P2 +V3.3A_MINI_2 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 49: Mini-Pcie (Usb)
Definition MINI_MIC_P +V3.3A_MINI_4 MINI_MIC_N MINI_SPK_PRR SMS_RI_3.5G_R U_GND UIM_PWR2 UMTS_RESET#_R UIM_DAT2 USB- VCC_MSM26_DIG UIM_CLK2 USB+ UIM_RST2 +V3.3A_MINI_4 +V3.3A_MINI_4 3.5G_LED#_R 3.5G_DIS# PCM_CLK 3.5G_RST# PCM_RX +V3.3A_MINI_4 PCM_TX PCM_SYNC +V3.3A_MINI_4 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 50: Chapter 4: Mechanical Dimensions
Chapter 4: Mechanical Dimensions Chapter 4: Mechanical Dimensions Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 51: Chapter 5: System Setup
Prior to removing the chassis cover, make sure the unit’s power CAUTION! CAUTION! CAUTION! is off and disconnected from the power sources to prevent electric shock or system damage. Front View Rear View Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 52: Installing The First Wwan Module
This WWAN module is paired with SIM socket 1. disappears inside the slot. Then fasten screws into the mounting holes to secure the module. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 53 3. Attach one end of the RF cable onto the module. 4. Mount the other end of the cable to the antenna mounting hole (WWAN) located at the front panel of the chassis. WWAN antenna hole Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 54: Installing The Second Wwan Module
WWAN module is paired with SIM socket 2. disappears inside the slot. Then fasten screws into the mounting holes to secure the module. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 55 3. Attach one end of the RF cable onto the module. 4. Mount the other end of the cable to the antenna mounting hole (WWAN) located at the front panel of the chassis. WWAN antenna hole Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 56: Installing A Wireless Lan Module
Then fasten screws into the mounting holes to secure the module, and attach one end of the RF cable onto the module. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 57 Chapter 5: System Setup 3. Mount the other end of the cable to the antenna mounting hole (WLAN) located at the front panel of the chassis. WLAN antenna hole Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 58: Installing A Sata Ssd Drive
2. Fasten the HDD bracket within the chassis and connect the SATA data and power cable onto connectors CN14 and CN11. the four screws. SATA data connector (CN14) SATA power connector (CN11) Mounting screws Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 59: Installing A So-Dimm
1. Connect capture card cable onto the capture card. Apply firm even pressure to each end of the module until it slips down 2. Connect capture card cable to the J5 connector on VTC 1010. into the socket. The contact fingers on the edge of the module will almost completely disappear inside the socket. -
Page 60: Appendix A: Software Demo Utility For I/O Ports Of Function Control
Software Demo Utility for I/O Ports of Function Control NEXCOM’s software demo utility enables users to test and control different I/O port functions on the VTC 1010. This document shows how to use the utility. There are also source code files of the utility in the CD. Users can refer to the source codes to develop their applications. -
Page 61: 1.1 Status
Press the button of Battery Status, the status of battery voltage will be shown. Low voltage …… Car battery is at low voltage. OFF ..…..Car battery is not at low voltage. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 62: 1.2 Gpio Setting
Selects the GPO ports and makes the output low or high. Shows the status of the MCU GPI. 1.2.3 GPI Read Reads the status of GPI. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 63: 1.4 Wdt Setting
Sets the On/Off of the GPIO LED on front panel. 1.5 3G Module Enables or disables the WWAN function. SIM card 1 or SIM card 2 can also be selected for the WWAN module. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 64: Rs-422/Rs-485
Enables or disables the power on delay time function. There are 8 selections of delay time. 1.8 Power Off Delay Time Enables or disables the power off delay time function. There are 8 selections of delay time. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 65: 1.9 Wake Up Function
Enables or disables the RTC wake up function. The timer setting of RTC is located in BIOS setting. 2.0.3 CN9 On/Off Power on or off CN9. 2.0.4 GPS Module Power On/Off Power on or off the GPS module. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 66: 2.1 Can Bus Setting
Reset OBDII module. 2.1.2 OBDII Module Power Reset Reset the power of OBDII module. 2.1.3 On Board CAN2.0B Data Link Status Reads the connection status of CAN2.0B Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 67: Appendix B: Gps Feature
Qualification tests are performed as stipulated in the ISO16750 lowest noise figure (NEO-M8N/Q) standard: “Road vehicles – Environmental conditions and testing for electrical and electronic equipment”. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 68 Manufactured and fully tested in ISO/TS 16949 certified production sites Configurable 0.25 Hz to 10 MHz Protocols NMEA, UBX binary, RTCM Uses u-blox M8 chips qualified according to AEC-Q100 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 69: Appendix C: Pin Definition For The Multiport Cable
Event Button Dead Reckening When connecting the multiport cable, please make sure the CAUTION! CAUTION! CAUTION! top side labeled “TOP” is facing upwards. This side facing upwards Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 70: P1 Connector Pinout
Connector location: P2 P1 Pin P3 Pin Definition SP_DCD_3 SP_RXD_3 SP_TXD_3 SP_DTR_3 ISO_GND SP_DSR_3 SP_RTS_3 SP_CTS_3 P1 Pin P2 Pin Definition SP_RI_3 OUT_12V OUT_12V 1, 3, 4, 6 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 71: Gpio + Can Bus 2.0B Connector
P4 Pin Definition P1 Pin P5 Pin Definition GPIO1 CAN_M_L GPIO2 C1708_1_L GPIO3 ISO_GND GPIO4 CAN_M_H ISO_GND C1708_1_H GPIO5 1, 2, 6, 7 CAN1_H CAN1_L GPIO6 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 72: Usb Connector
P1 Pin P6 Pin Definition P1 Pin P7 Pin Definition USB1_POWER (+5V) RS485_+ USB_2N_L (-) RS485_- USB_2P_L (+) RS422_TX+ USB_GND (GND) RS422_TX- ISO_GND 6, 7, 8, 9 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 73: Reset Button
Connector location: P9 P1 Pin P8 Pin Definition P1 Pin P9 Pin Definition Rear Panic (+) DIRECTION ISO_GND (-) ODOMETER 1PPS ISO_GND 2, 4, 7, 8, 9 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 74: A/V1 Jack
Connector type: BNC Connector location: P10 Connector location: P11 P1 Pin P10 Pin Definition P1 Pin P11 Pin Definition CAP1_A (+) CAP1_B (+) ISO_GND (-) ISO_GND (-) Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 75: A/V3 Jack
Connector type: RCA Connector location: P12 Connector location: P13 P1 Pin P12 Pin Definition P1 Pin P13 Pin Definition CAP2_A (+) CAP2_B (+) ISO_GND (-) ISO_GND (-) Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 76: Front Audio
Connector location: P14 Connector location: P15 P1 Pin P14 Pin Definition P1 Pin P15 Pin Definition AGND AGND FRONT_L_C CEN_C Jack Detection Jack Detection FRONT_R_C LFE_C Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 77: Surround Audio
Connector location: P16 Connector location: P17 P1 Pin P16 Pin Definition P1 Pin P17 Pin Definition AGND AGND SURR_OUT_L_C SIDE_L_C Jack Detection Jack Detection SURR_OUT_R_C SIDE_R_C Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 78: Appendix D: Signal Connection Of Di/Do
Note: By default, pin 1, 2 and 3 are configured for GPO, while pin 4, 5 and 6 are configured for GPI. Default Settings: GPIO (SW1) SW1.1~SW1.6 Pull up VCC5 Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 79: Digital Input
G_IN4 CAN1_H GPIO3 CAN1_L ISO_GND GPIO4 GPIO6 External Port Switch Register ISO_GND ON (Short) OFF (Open) HIGH External Port Switch Register ON (Short) OFF (Open) OPEN Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 80: Digital Output
G_IN2 GPIO2 G_IN1 GPIO5 G_IN3 CAN1_H GPIO3 G_IN2 GPIO2 CAN1_L G_IN3 CAN1_H GPIO4 GPIO3 GPIO6 CAN1_L GPIO4 GPIO6 Port Port Register Register ISO_GND HIGH OPEN ISO_GND Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... -
Page 81: Appendix E: Vehicle Power Management Setup
External Power Output Setting Startup and Shutdown Voltage Setting VTC 1010 has four modes for external power output setting. Set the startup voltage to 11.5V or 23V and the shutdown voltage to 10.5V or 21V 1. External +12V and By Pass Car Battery Turn On Simultaneously If the input voltage is 12V: the startup voltage to 11.5V and the shutdown... - Page 82 F4: Save & Exit F4: Save & Exit ESC: Exit ESC: Exit Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 83: Power-On Delay Setting
Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 84 F4: Save & Exit F4: Save & Exit ESC: Exit ESC: Exit Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 85: Power-Off Delay Setting
F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual... - Page 86 06 hour F1: General Help 18 hour F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2010 American Megatrends, Inc. Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
-
Page 87: Appendix F: Power Consumption
Appendix F: Power Consumption OS: Windows 8 Burn-in Software: Version 6.0 Device: 2G DDR3L and SSD Idle Mode Burn-in Mode 494mA/12V 0.92A/12V 88mA/12V 6mA/12V 6mA/12V 1.1W 0.1W 0.1W Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. VTC 1010 User Manual...
Need help?
Do you have a question about the VTC 1010 and is the answer not in the manual?
Questions and answers