Related Manuals for Nexcom ATC 8010
Summary of Contents for Nexcom ATC 8010
- Page 1 NEXCOM International Co., Ltd. Mobile Computing Solutions Artificial Intelligent Platform ATC 8010 User Manual NEXCOM International Co., Ltd. www.nexcom.com Published November 2018...
-
Page 2: Table Of Contents
Chapter 2: External Connectors Pinout Description Precautions ..................18 Dual HDMI Connector .................6 Jumper Settings ..................19 Dual HDMI Connector .................7 Locations of the Jumpers and Connectors for the Motherboard ..20 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 3 PoE Power & Low Speed Signal Connector ........36 PoE High Speed Signal Connector ..........37 Locations of the Jumpers and Connectors for the PoE Expansion Module (VIOB-POE8-03) ........38 Top View ..................38 Internal Connectors ................39 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 4: Preface
Acknowledgements The product(s) described in this manual complies with all applicable ATC 8010 is a trademark of NEXCOM International Co., Ltd. All other European Union (CE) directives if it has a CE marking. For computer systems product names mentioned herein are registered trademarks of their to remain CE compliant, only CE-compliant parts may be used. -
Page 5: Rohs Compliance
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm. In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products. The task force will ensure that we follow the standard... -
Page 6: Warranty And Rma
▪ Replace with 3rd party products if needed. ▪ Customers must collect all the information about the problems ▪ If RMA goods can not be repaired, NEXCOM will return it to the customer encountered and note anything abnormal or, print out any on-screen without any charge. - Page 7 Always power off the system before inserting or removing the SIM only with the same or equivalent type recommended by the manufacturer. card. Discard used batteries according to the manufacturer’s instructions. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
- Page 8 ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. rating marked on the product. ▪ All cautions and warnings on the equipment should be noted. viii Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 9: Technical Support And Assistance
Preface Technical Support and Assistance Conventions Used in this Manual 1. For the most updated information of NEXCOM products, visit NEXCOM’s Warning: website at www.nexcom.com. Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself 2. -
Page 10: Global Service Contact Information
13F, No.920, Chung-Cheng Rd., ZhongHe District, Beijing, 100094, China New Taipei City, 23586, Taiwan, R.O.C. Tel: +86-10-5704-2680 Tel: +886-2-8226-7796 Fax: +86-10-5704-2681 Fax: +886-2-8226-7792 Email: sales@nexcom.cn Email: sales@nexcom.com.tw www.nexcom.cn www.nexcom.com.tw Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 11 Hui Yin Ming Zun Building Room 1108, Building No. 11, 599 Yunling Road, Putuo District, Shanghai, 200062, China Tel: +86-21-6125-8282 Fax: +86-21-6125-8281 Email: frankyang@nexcom.cn www.nexcom.cn Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 12: Package Contents
Preface Package Contents Before continuing, verify that the ATC 8010 package that you received is complete. Your ATC 8010 package should have all the items listed in the following table. Item Name Specification 603ANT0115X00 GPS/GLONASS Antenna SANAV:SM-76G SMA Male L=5000mm ATC8101-7A DVD Driver VER:1.0... -
Page 13: Chapter 1: Product Introduction
COM1 COM2 DC OUT DC IN 9V-36V HDMI SIM2 Reset Power Mic-in PoE 1-4 PoE 5-8 SIM3 Button Button SSD/HDD SSD/HDD Antenna Hole GbE LAN COM3 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 14: Overview
Chapter 1: Product Introduction Overview Key Features ATC 8010, powerful and reliable Artificial Intelligent (AI) platform, is specially • Intel Coffee Lake-S Desktop, i7-8700T, 2.4GHz ® designed for applications, such as ANPR, AFR and highly-demanding on • NVIDIA GTX 1050Ti MXM graphic module supported graphics performance. -
Page 15: Hardware Specifications
- 4 x DI and 4 x DO Galileo/Beidou ▪ 4 x SMA antennas ▪ Optional modules with dead reckoning available ▪ 4 x USB 3.1 type A (5V/1A) ▪ Built-in TPM 2.0 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 16 - Storage: MIL-STD-810G, Method 514.6, Category 24, minimum integrity test ▪ Shock (SSD) - Operating: MIL-STD-810G, Method 516.6, Procedure I, functional shock=40g - Non-operating: MIL-STD-810G, Method 516.6, Procedure V, crash hazard shock test=75g Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 17: Connector Numbering
The following diagrams indicate the numbers of the connectors. Use these numbers to locate the connectors’ respective pinout assignments on chapter 2 of the manual. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 18: Chapter 2: External Connectors Pinout Description
Definition Definition HDMI_A_TX2P HDMI_B_TX2P HDMI_A_TX2N HDMI_A_TX1P HDMI_B_TX2N HDMI_B_TX1P HDMI_A_TX1N HDMI_B_TX1N HDMI_A_TX0P HDMI_B_TX0P HDMI_A_TX0N HDMI_A_CLKP HDMI_B_TX0N HDMI_B_CLKP HDMI_A_CLKN HDMI_B_CLKN HDMI_A_SCL HDMI_A_SDA HDMI_B_SCL HDMI_B_SDA HDMI_P5V HDMI_P5V HDMI_A_HPD HDMI_B_HPD Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 19: Dual Hdmi Connector
Definition Definition HDMI_C_TX2P HDMI_D_TX2P HDMI_C_TX2N HDMI_C_TX1P HDMI_D_TX2N HDMI_D_TX1P HDMI_C_TX1N HDMI_D_TX1N HDMI_C_TX0P HDMI_D_TX0P HDMI_C_TX0N HDMI_C_CLKP HDMI_D_TX0N HDMI_D_CLKP HDMI_C_CLKN HDMI_D_CLKN HDMI_C_SCL HDMI_C_SDA HDMI_D_SCL HDMI_D_SDA HDMI_P5V HDMI_P5V HDMI_C_HPD HDMI_D_HPD Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 20: Ultraone+ Connector
Definition Definition Definition Definition USB D- VGA_RED VGA_GREEN FPT LINKIII D- POWER BUTTON VGA_BLUE USB D+ FPT LINKIII D+ 24V ENABLE DETECT VGA_DATA VGA_HS VGA_VS VGA_CLK Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 21: Dual Usb 3.1 Port
Definition Definition USB_1N HDMI_TX2P USB_1P HDMI_TX2N HDMI_TX1P USB3_RX1N USB3_RX1P HDMI_TX1N USB3_TX1N HDMI_TX0P USB3_TX1P HDMI_TX0N HDMI_CLK_P USB_2N USB_2P HDMI_CLK_N USB3_RX2N USB3_RX2P HDMI_SCL HDMI_SDA USB3_TX2N USB3_TX2P HDMI_P5V HDMI_HPD Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 22: Sim2 And Sim3 Sockets
Reset Button Connector number: 7 Connector number: 8 SIM2 Definition Definition Definition UIM_PWR UIM_RST UIM_DAT RST_BTN# UIM_CLK SIM3 Definition Definition UIM_PWR UIM_RST UIM_DAT UIM_CLK SIM SELECT Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 23: Power Button
Chapter 2: External Connectors Pinout Description Power Button Mic-in Connector Connector number: 9 Connector number: 10 Definition Definition Definition Definition HW_BT# MIC RIGHT HW_BT# MIC DETECT PWRLED_A PWRLED_C MIC LIFT Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 24: Line-Out Connector
Connector number: 12 Definition Definition Definition Definition FRONT OUT RIGHT USB_5N FRONT OUT DETECT FRONT LIFT USB_5P USB3_RX5N USB3_RX5P USB3_TX5N USB3_TX5P USB_6N USB_6P USB3_RX6N USB3_RX6P USB3_TX6N USB3_TX6P Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 25: Dual Usb 3.1 Port
CAN H ODOMETER USB_3P GPO3 GPI1 USB3_RX3N USB3_RX3P GPO0 CAN L USB3_TX3N DIRECTION USB3_TX3P GPI2 GPO1 USB_4N USB_4P CAN GND USB3_RX4N GPI3 GPO2 USB3_RX4P GPI0 USB3_TX4N USB3_TX4P Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 26: Com1 Rs232 Connector
Definition DTR1 RS232 DCD#/RS422 TX- RS232 RX/RS422 TX+ TXD1 RXD1 RS232 TX/RS422 RX+ RS232 DTR#/RS422 RX- DCD1 RS232 DCD#/RS422 TX- CTS1 RTS1 DSR# RTS# DSR1 CTS# Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 27: Com2 Rs232 Connector
Connector number: 17 Connector number: 18 Definition Definition Definition Definition DTR2 RESET BUTTON## SLEEP BUTTON## TXD2 RXD2 DCD2 RS232 TX RS232 RX CTS2 RTS2 POWER BUTTON# DSR2 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 28: 9V-36V Dc Power Input
Chapter 2: External Connectors Pinout Description 9V-36V DC Power Input LAN Port Connector number: 19 Connector number: 20 Definition Definition Definition Definition LAN_MDI_0P_R LAN_MDI_0N_R LAN_MDI_1P_R LAN_MDI_1N_R IGNITION LAN_MDI_2P_R LAN_MDI_2N_R LAN_MDI_3P_R LAN_MDI_3N_R Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 29: Poe1 To Poe4 Ports
LANX_MDI_0P LANX_MDI_0N LANX_MDI_1P LANX_MDI_2P LANX_MDI_1P LANX_MDI_2P LANX_MDI_2N LANX_MDI_1N LANX_MDI_2N LANX_MDI_1N LANX_MDI_3P LANX_MDI_3N LANX_MDI_3P LANX_MDI_3N Red ‘X’ denotes the port number. Red ‘X’ denotes the port number. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 30: Chapter 3: Jumpers And Switches
3: J haPter umPers and wItChes This chapter describes how to set the jumpers on the ATC 8010 motherboard. Precautions Before You Begin ▪ Ensure you have a stable, clean working environment. Dust and dirt can Computer components and electronic circuit boards can be damaged by discharges of static electricity. -
Page 31: Jumper Settings
(on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right) Three-Pin Jumpers: Pins 1 and 2 are Short Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 32: Locations Of The Jumpers And Connectors For The Motherboard
Chapter 3: Jumpers and Switches ATC 8010 System Components The ATC 8010 consists of a motherboard and PoE board. This chapter describes the location and pinout assignment of the jumpers and connectors on each component. Locations of the Jumpers and Connectors for the Motherboard... -
Page 33: Bottom View
Chapter 3: Jumpers and Switches Bottom View Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 34: Dip Switch Settings
Connector location: SW1 RTC (Pin1) SRTC/ME (Pin2) RTC (Pin1) SRTC/ME (Pin2) Normal Normal 1~2 ON 120 OHM 1~2 ON Clear CMOS Clear ME 1~2 OFF 1~2 OFF Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 35: Input Voltage Setup Selection
1280 x 960 18-bit Single Port 0110 800 x 480 18-bit Single Port 0111 1366 x 768 18-bit Single Port 1000 1366 x 768 24-bit Single Port Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 36: Internal Connectors
Connector size: 1 x 10 = 10-pin header (1.0mm) Connector location: J11 Connector location: IDE1 Definition Definition Definition Definition UIM_PWR CTS1 DSR1 UIM_RST UIM_DAT DTR1 RXD1 UIM_CLK RTS1 TXD1 DCD1 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 37: Gps Wire To Board Connector
Connector size: 1 x 6 = 6-pin header Connector size: 1 x 4 = 4-pin header Connector location: J2 Connector location: J1 Definition Definition Definition Definition 3.3V GPS LED ODOMETER DIRECTION 3.3V Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 38: Gps Battery Connector
Connector size: 1 x 2 = 2-pin header Connector size: 1 x 2 = 2-pin header Connector location: J3 Connector location: J6 Definition Definition VBAT VBAT Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 39: Rtc Battery Connector
Connector location: CN13 Connector location: J4 Definition Definition Definition Definition FAN1 CONTROL PCIRST# FAN1 SPEED 33M_CLK LPC_FRAME# FAN2 SPEED FAN2 CONTROL LPC_AD3 LPC_AD2 LPC_AD1 LPC_AD0 VCC3 VCC3 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 40: Usb Connectors (Reserved)
Connector size: 1 x 4 = 4-pin header (1.0mm) Connector size: 1 x 6 = 6-pin header (2.54mm) Connector location: J8 and J10 Connector location: JP6 Definition Definition Definition Definition 3.3V SWDIO SWDCLK RESET# Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 41: Can-Mcu Debug Port
Connector size: 1 x 3 = 3-pin header (2.54mm) Connector size: 1 x 3 = 3-pin header (2.54mm) Connector location: JP3 Connector location: JP2 Definition Definition Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 42: Mcu Download Port
Chapter 3: Jumpers and Switches MCU Download Port Connector size: 2 x 4 = 8-pin header (1.27mm) Connector location: JP5 Definition Definition 3.3V MCU_TRST MCU_TCK MCU_TDO MCU_RST MCU_TDI MCU_TMS Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 43: Mini-Pcie Connector
Definition Definition Definition +V3.3_MINI_2 +V1.5S_MINI_2 W_SM2_C +V1.5S_MINI_2 PCIE_TXN17_SATA_TXN4_C W_SM2_D CLKREQ#2 PCIE_TXP17_SATA_TXP4_C USB_10N_T MINICARD2_CN USB_10P_T MINICARD2_CP +V3.3_MINI_2 +V3.3_MINI_2 MINIPCIE2_WLAN_LED#_R MINIPCIE2_DIS# MINIPCIE2_RST# +V1.5S_MINI_2 PCIE_RXP17_SATA_RXP4_R +V3.3_MINI_2 PCIE_RXN17_SATA_RXN4_R SSD4_DETECT +V3.3_MINI_2 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 44: Mini-Pcie Connector
Definition Definition Definition +V3.3_MINI_3 +V1.5S_MINI_3 W_SM3_C +V1.5S_MINI_3 PE_TX18N_C W_SM3_D CLKREQ#3 PE_TX18P_C USB_11N_T PCIE_CN3 USB_11P_T PCIE_CP3 +V3.3_MINI_3 +V3.3_MINI_3 MINIPCIE3_WLAN_LED#_R MINIPCIE3_DIS# MINIPCIE3_RST# +V1.5S_MINI_3 PE_RX18N_R +V3.3_MINI_3 PE_RX18P_R MBT_DIS#_R +V3.3_MINI_3 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 45: Mini-Pcie Connector
SMB_CLK +1.5V PCIE_TXN3 SMB_DATA PCIE CLOCK REQUEST# PCIE_TXP3 USB_5N PCIE_CLKN3 USB_5P PCIE_CLKP3 +3.3V +3.3V PCIE3_WLAN_LED# PCIE3 DISABLE# PCIE3 RESET# +1.5V PCIE_RXP3 +3.3V PCIE_RXN3 BT DISABLE# +3.3V Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 46: M.2 B-Key Connector
3.3V 3.3V POWER_OFF# USB_9P_T W1_DIS# USB_9N_T MINICARD1_WWAN_LED# CONFIG0 SMB_DATA SMS_RI_3.5G_R SMB_CLK W2_DIS# USB3_RXN9_T SW2_RST USB3_RXP9_T SW2_CLK SW2_DAT RESET# USB3_TXN9_T SW2_PWR CONFIG1 3.3V USB3_TXP9_T 3.3V 3.3V CONFIG2 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 47: B-Key Connector
3.3V POWER_OFF# USB_7P_T W1_DIS# USB_7N_T LTE_LED_PH PEWAKE# CONFIG0 SM1_D SM1_C W2_DIS# USB3_PXN7_T SW1_RST USB3_PXP7_T SW1_CLK SW1_DAT RST# SUSCLK_R USB3_TXN7_T SW1_PWR CONFIG1 3.3V USB3_TXP7_T 3.3V 3.3V CONFIG2 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 48: Poe Power & Low Speed Signal Connector
POE_PW_ERR# V3P3_LAN1 MCU_I2C1_SDA EXP_ID_1 LAN_ACTIVE_LED8 EXP_ID_2 POE_INSERT# PCH_SMB_CLK EXP_ID_3 SIO_AGND USB_13N PCH_SMB_DATA EXP_ID_4 POE_THER USB_13P SLP_S3# VCC3_POK SLP_S5# USB_12N USB_14N VCC_EN EXP_POE_POK USB_12P USB_14P MB_MCU_PSE_PWREN WAKE_ON_LAN_EN Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 49: Poe High Speed Signal Connector
PCIE_RXN24 PCIE_TXN24 PCIE_RXP14 PCIE_TXP14 PCIE_CLKP5 PCIE_CLKP14 PCIE_RXN14 PCIE_TXN14 PCIE_CLKN5 PCIE_CLKN14 PCIE_RXP15 PCIE_TXP15 SATA_TXP0B SATA_TXP0A PCIE_RXN15 PCIE_TXN15 SATA_TXN0B SATA_TXN0A PCIE_RXP16 PCIE_TXP16 SATA_RXN0B SATA_RXN0A PCIE_RXN16 PCIE_TXN16 SATA_RXP0B SATA_RXP0A Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 50: Locations Of The Jumpers And Connectors For The Poe Expansion Module (Viob-Poe8-03)
Chapter 3: Jumpers and Switches Locations of the Jumpers and Connectors for the PoE Expansion Module (VIOB-POE8-03) Top View SATA1 SATA2 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 51: Internal Connectors
SATA Connectors (7-pin and 15-pin) Connector type: Standard Serial ATA 7P and 15P Connector location: SATA1 & SATA2 Definition Definition SATA_TXP SATA_TXN SATA_RXN SATA_RXP VCC5 VCC5 VCC5 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 52: Low Speed Board To Board Connector
+V3.3ALW MCU_I2C3_SCL_M V3P3_LAN1 POE_ERRLED# EXP_ID_1 MCU_I2C3_SDA_M EXP_ID_2 EXP_ID_3 SMB_CLK USB_13N X550_THERM-DN EXP_ID_4 SMB_DATA USB_13P X550_THERM-DP PM_SLP_S3# PM_SLP_S5# VCC3_POK USB_14N USB_15N EXP_POE_ALLPOK VCC_EN USB_14P USB_15P WAKE_ON_LAN_EN MB_MCU_PSE_PWREN Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 53: High Speed Board To Board Connector
PCIE_RXN24 PCIE_TXN24 PCIE_RXP14 PCIE_TXP14 PCIE_CLKP5 PCIE_CLKP14 PCIE_RXN14 PCIE_TXN14 PCIE_CLKN5 PCIE_CLKN14 PCIE_RXP15 PCIE_TXP15 SATA_TXP1 SATA_TXP0 PCIE_RXN15 PCIE_TXN15 SATA_TXN1 SATA_TXN0 PCIE_RXP16 PCIE_TXP16 SATA_RXP1 SATA_RXP0 PCIE_RXN16 PCIE_TXN16 SATA_RXN1 SATA_RXN0 Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 54: Chapter 4: System Setup
1. Remove the screws on the front panel. 2. Remove the screws on the rear panel. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 55 3. Remove the mounting bracket screws on the bottom of the enclosure. 4. After removing the brackets, loosen the screws on the bottom then remove the chassis top cover. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 56: Removing The Mxm Module
Chapter 4: System Setup Removing the MXM Module 1. Remove the screws securing the MXM module. 2. Remove the MXM module from the socket. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 57: Removing The Cpu
2. Lift the load plate up and remove the CPU from the socket. down, moving it sideways until it is released from the retention tab; then lift the load lever up. Load Lever Retention Tab Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 58: Removing The Memory Module
Mini PCI Express slot at a 45 degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot. Then fasten screws into the mounting holes to secure the module. Mounting Screws Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 59: Installing A Wwan Module (M.2)
Then the mounting hole to secure the module. fasten a screw into the mounting hole to secure the module. Mounting Mounting Screw Screw Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 60: Installing A Sim Card
1. Remove the SIM card cover. 2. Insert the SIM card into the SIM card slot. 3. Close the cover and secure it to the original position. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 61: Installing A Ssd/Hdd Drive
Align the storage drive’s mounting holes with the mounting holes on the drive bay, and use the provided screws to secure the storage drive in place. Thumb Screws Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 62 Chapter 4: System Setup 3. Insert the drive bay back to its original position and secure the thumb screws. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 63: Replacing The System Fan
1. Loosen the thumb screws on the front panel. 2. Loosen the thumb screws on the rear panel. The fan kit can be removed from the top cover. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 64 3. On the top cover, loosen the mounting screws of the fan kit that will be 4. Turn to the back side of the top cover and loosen the screws on the replaced. cover for the fan cable connectors. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
- Page 65 5. Turn to the back of the fan cable cover and remove the fan cable connector that will be replaced. Then proceed to install the new fan kit. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 66: Appendix A: Software Demo Utility For I/O Ports Of Function Control
Menu Screen 1. Config1 1.1 System Information Displays basic information of the system. 1.2 WWAN Enables or disables the WWAN function and the wake-up function. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 67 1.7 SIM Card Selects the SIM Card for WWAN. 1.4 WiFi Enables or disables the WiFi function. 1.5 Bluetooth Enables or disables the Bluetooth function. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 68: Config2
Appendix A: Software Demo Utility for I/O Ports of Function Control 2. Config2 2.1 GPO Configures GPO as high voltage level or low voltage level. 2.2 GPI Reads the status (voltage level) of GPI. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... - Page 69 Turns On/Off LED light. 2.4 Wake On LAN Enables or disables the Wake On LAN function on LAN. 2.5 External 12V Enables or disables the 12VDC power output. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
-
Page 70: Config3
Enables or disables low battery voltage protection function. Once it is enabled, one of 4 types of voltage levels can be selected. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 71: G-Sensor
Selects the registers inside G-Sensor to read or write the data. 4.2 Register Table Shows the value of all registers in G-Sensor, once the Refresh button is pressed. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 72: Poe
Shows the power output of each PoE port. 5.3 Link Status Shows the status of PoE link. 5.4 Total Output (W) Shows the total power output of all PoE ports. Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual... -
Page 73: System Event
The System Event tab shows the following alarm messages: 1. Over voltage alarm 2. Lower voltage alarm 3. Over temperature alarm 4. Lower temperature alarm 5. Fan error alarm Copyright © 2018 NEXCOM International Co., Ltd. All Rights Reserved. ATC 8010 User Manual...
Need help?
Do you have a question about the ATC 8010 and is the answer not in the manual?
Questions and answers