Table of Contents
Advertisement
Quick Links
Manual Type 6.2.0.1-RF
For Models
Communication
For use with all Panasonic KSUs with door phone
card. This unit is a replacement for the Panasonic
KXT-30865 door phone.
Intercom to KSU
Not Used
12 VDC input (for camera and keypad)
NO, COM, NC relay connections
Keypad case ground
Remote bypass terminals (activate relay)
Connect tamper switch to alarm (optional)
"Panasonic Compatible" Unit with Essex
"S-12 Stand - Alone" Keypad
400-S12-PAN
401-S12-PAN
403-S12-PAN
404-S12-PAN
410-S12-PAN
411-S12-PAN
Specifications
Access Control
Essex "stand-alone" 12 button keypad
1 relay plus 2 grounding outputs
(external relays required)
500 users
12 VDC power supply included
400 Series "S-12" Junction Board
Loop for Strike Power
Cut for NO Contact Closure
INSTALLATION
INSTRUCTIONS
501 E. Goetz Ave.
Santa Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax 800-362-0002
HOLOVISION
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HOLOVISION 400-S12-PAN
Summary of Contents for HOLOVISION 400-S12-PAN
-
Page 1: Specifications
INSTALLATION INSTRUCTIONS Manual Type 6.2.0.1-RF “Panasonic Compatible” Unit with Essex “S-12 Stand - Alone” Keypad For Models 400-S12-PAN 401-S12-PAN 403-S12-PAN 404-S12-PAN 410-S12-PAN 411-S12-PAN Specifications Communication Access Control For use with all Panasonic KSUs with door phone Essex “stand-alone” 12 button keypad card. - Page 2 Essex Keypad Wiring DC Out for Gate Strike Strike 1 To Phones Door 1 12vDC 1.5 A AC Loop for Strike Cut for NO Contact Closure Gate Strike Remote Bypass Button NOTE: MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick back”...
- Page 3 Essex Keypad Wiring Contact Closure for Gate Operation Strike 1 To Phones Door 1 12vDC 1.5 A AC Loop for Strike Cut for NO Contact Closure Page 3 Type 6.2.0.1-RF...
- Page 4 Programming the Essex Keypad Set Keypad Illumination to ON ALL OF THE TIME STEP ACTION BEEP Red LED Green LED Remove power Jumper the “CONFIG” pins on the rear of the keypad . V = 12 Apply 12 VDC power to red and black wires Quadruple Beep Flash Solid...
- Page 5 Programming the Essex Keypad Set User Codes STEP ACTION BEEP Red LED Green LED The Master Code is necessary to do this step. Master Code “123” is used as an example. Enter 1 1 2 3 Double Beep Slow Flash Solid Enter Double Beep...
- Page 6 Programming the Essex Keypad Deleting User Codes - using User Code/PIN STEP ACTION BEEP Red LED Green LED The Master Code is necessary to do this step. In this example, the Master Code is 123 1 1 2 3 Enter Double Beep Slow Flash Solid...
- Page 7 Programming the Essex Keypad Reset Keypad to Factory Defaults--- This is not normally necessary, but can be done as follows STEP ACTION BEEP Red LED Green LED Remove power Jumper the “CONFIG” pins on the rear of the keypad Apply 12 VDC power to red and black wires ONLY Quadruple Beep Flash Solid...
- Page 8 501 E. Goetz Ave. Santa Ana, Ca 92707 Ph. 714-434-6904 Fax 800-362-0002 www.eholovision.com...
Need help?
Do you have a question about the 400-S12-PAN and is the answer not in the manual?
Questions and answers