Page 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Products Are Water Tested At Our Factory. UNPACKING Some Residual Water May Remain In The Valve During Shipping.
(15-7/8") Spud Fixtures 389 mm x 265 mm FINISHED WALL (15-5/16" X 10-3/8") ROUGH OPENING FOR BOX CAUTION: Use only American Standard supplied transformers and cable sets. 15˚ 15˚ Using non-AS supplied cables, or cutting, SENSOR splicing or modifying any components will void the warranty.
Page 4
Fig. 3 (TOP SPUD FIXTURE ILLUSTRATED) FLUSH VALVE INSTALLATION 389mm ROUGH OPENING IN WALL (15-5/16") LEVEL INSTALL ELECTRICAL BOX; Fig. 3 265mm 1. Frame out a 389mm x 265mm (15-5/4" X 10-3/8") rough (10-3/8") opening in wall for the WALL BOX (1) at the dimension shown.
Page 5
INSTALL VACUUM BREAKER AND Fig. 6 FLUSH CONNECTIONS; Fig. 6 . Place the SPUD FLANGE (1) over the spud on the Fixture. 3/4" TOP SPUD Fig. 6. 2. Place FRICTION WASHER (3) and SEAL WASHER (4) inside SPUD COUPLING NUT (2) and thread onto Spud. Do not tighten fully.
Page 6
INSTALL FLUSH VALVE; Fig. 7 Fig. 7 Insert the side ADJUSTABLE TAILPIECE (1) on the FLUSH VALVE (2) into the STOP VALVE (3). Lubricate the TAILPIECE O-RING (4) with water if necessary. Thread the COUPLING NUT (5) onto the STOP VALVE (3) and tighten lightly.
ELECTRICAL INSTALLATION Fig. 9 Fig. 9 STANDARD BATTERY POWER KIT (PK00.CRP); Fig. 9, 9a 1. Connect one end of the 27" EXTENSION CABLE (1) to a SENSOR CABLE (2) and install the CONNECTOR LOCKING DEVICE (10). Connect the other end of the 27"...
Page 8
AC VERSION (PK00.PAC POWER Fig. 10 Fig. 10 KIT); Fig. 10, 10a 1. Connect one end of the first 27" EXTENSION CABLE (1) to SENSOR CABLE (5). Connect the other end of the 27" EXTENSION CABLE (1) to the SOLENOID CABLE (3). Fig.10.
Page 9
5. Place Y-ADAPTERS (3) into respective electrical box. 6. Plug in AC power supply into wall outlet once all daisy-chain unit connections have been made. CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.
Page 10
CONNECT OVERRIDE HOSES, Fig. 12 AC & DC POWER; Fig. 12 Push the BLACK HOSE (1) into the BOTTOM HOSE CONNECTOR (2) on flush valve body and push the other end into the back of the MANUAL OVERRIDE VALVE (3). Push the BLUE HOSE (4) into the TOP HOSE CONNECTOR (5) on flush valve body and push the other end into the BOTTOM CONNECTOR (6) of the...
MAINTENANCE Fig. 13 INSTALL NEW BATTERY; Fig. 13 1. Remove the six COVER PLATE SCREWS (1), then remove COVER PLATE (2). Fig. 13. 2. Remove old BATTERY (3). Install the new BATTERY (4), making sure the terminal side is inserted first and shape of the battery follows the shape of the BATTERY Fig.
Page 12
SET DETECTION RANGE (if required); Fig. 15 & 16 Fig. 15 Note: The detection distance is preset and ideal for most installations. Should an adjustment be required, follow the steps below. 1. Remove COVER PLATE (1). See Step A for removing front panel instructions.