13. Frameset Parts Checklist ......25-27 For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High-end components, particularly carbon parts, need extra care when assembled.
KRYPTON GF 273A & KRYPTON CS 273B: 3. Frameset Inspection BEFORE ASSEMBLING YOUR NEW KRYPTON CS /GF, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING: 1. Frameset parts checklist (see p.29-30) 2. Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.) 3.
KRYPTON GF 273A & KRYPTON CS 273B: 4. Troubleshooting / Tip / Specification Brakes Use only flat mount hydraulic disc brakes. The frame and fork are compatible with either 140mm or 160mm disc rotors. Adapters might be required, consult brake manufacturer.
Page 7
KRYPTON GF 273A & KRYPTON CS 273B: 5. Seat Post Collar Assembly CARBON PASTE 4 Nm Assemble the seat post collar with the seat post. Apply carbon paste on the seat post where it inserts inside the frame. Tighten the bolt at 4 Nm.
Page 8
KRYPTON GF 273A & KRYPTON CS 273B: 6. Seat Post Assembly The seat post is supplied fully assembled. It’s equipped with a spring-loaded head for easy installation of the saddle. • Unscrew both bolts slightly until the top clamp (b) and the cradle (c) are separated enough to insert the saddle rail.
KRYPTON GF 273A & KRYPTON CS 273B: 7. Rear Derailleur Hanger Adjustment 1. Select the correct rear derailleur hanger depending on the type of derailleur that you have. a. Direct mount b. Regular mount 2. Make sure to align the rear derailleur hanger.
9. Install the corresponding Like on almost all Argon 18 you will benefit of the 3D system, on the Krypton headset cap to complete the CS and GF you can benefit of 3 positions, 0mm, 15mm and 30mm assembly.
Page 11
KRYPTON GF 273A & KRYPTON CS 273B: 9. Console / A. Di2 internal junction box groupset The console is the central point of the cable and housing routing. Depending of the type of assembly you will have to select the correct assembly.
Page 12
KRYPTON GF 273A & KRYPTON CS 273B: 9. Console / B. Di2 external junction box groupset 1. With the rear brake housing coming from the back of the bike, guide the end of the housing through the opening of the console.
Page 13
KRYPTON GF 273A & KRYPTON CS 273B: 9. Console / C. Wireless groupset 1. With the rear brake housing coming from the back of the bike, guide the end of the housing through the opening of the mechanical console cap. (1) 2.
Page 14
KRYPTON GF 273A & KRYPTON CS 273B: 9. Console / D. Mechanical groupset 1. With the rear brake housing coming from the back of the bike, guide the end of the housing through the opening of the console. 2. Use the brake housing to insert the foam liner around the brake housing.
KRYPTON GF 273A & KRYPTON CS 273B: 9. Console / E. Mechanical Single chainring 1. With the rear brake housing coming from the back of the bike, guide the end of the housing through the opening of the mechanical console cap. (1) 2.
Page 16
KRYPTON GF 273A & KRYPTON CS 273B: 10. Hydraulic & mechanical shifter routing Rear derailleur cable and rear brake housing must be routed on the right side in the inside of the downtube. Red line: brake cable/housing / Blue line:...
Page 17
KRYPTON GF 273A & KRYPTON CS 273B: 10. Hydraulic & mechanical shifter routing DC = Derailleur Cable (mech.) Exit derailleur cables through bottom bracket (BB) hole. Insert in the appropriate slots in the BB guide. Making sure the pipe is aligned with the top hole,...
Page 18
KRYPTON GF 273A & KRYPTON CS 273B: 10. Hydraulic & mechanical shifter routing DC+DH BR = Brake Hose Exit the hydraulic brake hose through DC = Derailleur Cable (mech.) the hole on the chain stay. DH = Derailleur Housing (mech.)
Page 19
KRYPTON GF 273A & KRYPTON CS 273B: 10. Electronic wire routing Rear derailleur cable and rear brake housing must be routed on the right side in the inside of the downtube. Red line: brake cable/housing / Yellow line: derailleur cable/housing Rear brake housing need to routed above the bb carbon sleeve.
Page 20
KRYPTON GF 273A & KRYPTON CS 273B: 10. Electronic wire routing EW = Electronic Wire Use the square hole to connect all the wires to the junction box. Insert the junction box in the hole. Insert the BB cover in the square hole until it clicks.
Page 21
KRYPTON GF 273A & KRYPTON CS 273B: 10. Electronic wire routing BR = Brake Hose Exit the hydraulic brake hose through EW = Electronic Wire the hole on the chain stay.
Page 22
KRYPTON GF 273A & KRYPTON CS 273B: 10. Wireless routing Use the square hole to connect all the wires to the junction box. Insert the junction box in the hole. Insert the BB cover in the square hole until it clicks.
Page 23
KRYPTON GF 273A & KRYPTON CS 273B: 10. Wireless routing BR = Brake Hose Exit the hydraulic brake hose through the hole on the chain stay.
KRYPTON GF 273A & KRYPTON CS 273B: 11. Chain Catcher 1. Select the corresponding chain catcher. The selection of the correct chain catcher is made in function of the size of the small chaining. Small Chain Chain Ring Size Catcher...
KRYPTON GF 273A & KRYPTON CS 273B: 12. Fender bracket Maximum insertion of the screw: 10mm The maximum length insertion for the fender is the same on both seat stay. i. According to the model of fender using place the backet at the correct hight on the seatstay.