Download
Share
Print this page
Argon 18 KRYPTON XROAD 213C Assembly Manual
  1. Manuals
  2. Brands
  3. Argon 18 Manuals
  4. Bicycle
  5. KRYPTON XROAD 213C
  6. Assembly manual
Argon 18 KRYPTON XROAD 213C Assembly Manual

Argon 18 KRYPTON XROAD 213C Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
KRYPTON XROAD 213C: ASSEMBLY GUIDE
Revision 5.0 - 05-23-2017

Advertisement

loading

Related Manuals for Argon 18 KRYPTON XROAD 213C

Summary of Contents for Argon 18 KRYPTON XROAD 213C

  • Page 1 KRYPTON XROAD 213C: ASSEMBLY GUIDE Revision 5.0 - 05-23-2017...

  • Page 2: Table Of Contents

    7. Parts’ SKUs and Descriptions ......16 For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components, particularly carbon parts, need extra care when assembled.

  • Page 3: Frame Inspection

    KRYPTON XROAD 213C: Assembly overview 1. Frame inspection 2. Headset installation 3. Cable housing installation IMPORTANT NOTICE: It is easier to install the cables and cable housings before the crank set. 4. Electronic drive-train cable 5. Seatpost adjustment 6. Derailleur hanger adjustment...
  • Page 4 KRYPTON XROAD 213C: 1. Frame inspection When assembling a new frame, be sure to check if the following parts are assembled correctly. Parts installed on the frame Description Screw Tork Detail type Seatpost, Ø 27.2mm Seatpost Carbon paste Front derailleur hanger...
  • Page 5 KRYPTON XROAD 213C: 2. Headset installation Install the 3D headset (6) according to the pressfit assembly guide. You can choose from 3 different heights: 25mm, 15mm or 0mm.
  • Page 6 KRYPTON XROAD 213C: 3. Cable housing installation : barrel adjuster Install the front and rear derailleur cable starting at the top of the down tube. : plastic cap For the derailleur and hydraulic housing, measure a sufficient length B+A+B speed adjustment: of housing to be able to turn the handlebar both ways correctly.
  • Page 7 KRYPTON XROAD 213C: 3. Cable housing installation Hydraulic brakes housing Font section: Measure the necessary housing to ensure proper rotation of the handlebar. Insert the housing through the fork starting at the caliper. Rear section: Remove both brake grommets (4j - front & rear). Run the hydraulic housing from the back of the...
  • Page 8 KRYPTON XROAD 213C: 3. Cable housing installation Front and rear derailleur: Pass the two cables inside the frame starting the top tube until they come out under the bottom bracket. Pass both cables into the cable guide (4d). Make sure the 5mm screw is set to 1.5 Nm.

  • Page 9: Electronic Drive-Train Specification

    KRYPTON XROAD 213C: 4. Electronic drive-train specification The Di2 cable routing can be achieved easily using this simple trick: use a brake cable and a metal cable end to fix the Di2 cable. For more information on Shimano Di2 electronic system installation, go to: http://si.shimano.com.
  • Page 10 KRYPTON XROAD 213C: 4. Electronic drive-train specification Use the proper grommet on the downtube to fix the cable correctly, depending if you use mechanical (4h) or electronic (5b-5c) drive-train.
  • Page 11 KRYPTON XROAD 213C: 4. Electronic drive-train specification Use the proper grommet / cable stopper for the rear derailleur (depending if you use mechanical or electronic drive-train). In a Di2 configuration, remove the cable stopper (4g) and use the Di2 grommet (5a) instead, but leave the 2 screws to...
  • Page 12 KRYPTON XROAD 213C: 4. Electronic drive-train specification In a mechanical configuration, use the provided cable guide pipe (4f) for the front derailleur. For an electronic drive-train configuration, remove the cable guide pipe and use the proper grommet (5a) to fix...
  • Page 13 KRYPTON XROAD 213C: 4. Electronic drive-train specification The Di2 battery is hidden in the seatpost, use the 2 battery holders (8) to fix the battery correctly. Apply a slight amount of grease on both parts. GREASE...

  • Page 14: Saddle Adjustment

    KRYPTON XROAD 213C: 5. Saddle adjustment 9.1 Install the saddle on the rocker (3f) and tighten the rail clamp (3g) using the screw (3d) 9.2 Adjust the angle, the offset of the saddle and tighten the bolt (3b). GREASE 9.3 The rocker and the rail clamp (3f- 3g) can be flipped to change the saddle offset.

  • Page 15: Saddle Adjustment

    KRYPTON XROAD 213C: 5. Saddle adjustment Seat clamp offset (5mm) by flipping the rail clamp (3g) and rocker (3f).

  • Page 16: Derailleur Hanger Adjustment

    KRYPTON XROAD 213C: 6. Derailleur hanger adjustment The front derailleur hanger can be adjusted according to the front derailleur angle to obtain an equal curve between the derailleur and the LOCTITE big chain ring. Once at the right angle, use blue 242 Loctite and screw in at 6Nm.

  • Page 17: Parts' Skus And Descriptions

    KRYPTON XROAD 213C: 7. Parts’ SKUs and Descriptions 80096 36197 37830 SP.XROAD.212B 38891 38234 38446 36682 38258 38260 38257 38256 38892 38253 38756 38894 38893 FK.XROAD.213C Images are for reference only. Proportions are not accurate.
  • Page 18 KRYPTON XROAD 213C: 7. Parts’ SKUs and Descriptions* Name Assembled on A18 SKU# Parts already assembled Rear Derailleur Hanger Frame 37830 Front Derailleur Hanger Frame 36197 BB Cable Guide (incl. screw) Frame 38257 Bottle Cage Screws Frame 38234 BB Cable Guide Pipe...