Door Gasket Replacement - Market Forge Industries STEAM-TECH PLUS STP-6E Owner's Manual

Electric steam cooker
Table of Contents

Advertisement

ITEM
FIGURE 6.9 COOKING COMPARTMENT DOOR ASSEMBLY
NO.
DESCRIPTION
1
DOOR GASKET
2
DOOR GASKET MOUNTING PLATE
3
DOOR HANDLE
4
DOOR INSERT
5
DOOR SHELL
6
HINGE BEARING, NYLON
7
HINGE BRACKET, BOTTOM (SMALLER)
8
HINGE BRACKET, TOP (LARGER)
9
MAGNET
10
MAGNET RETAINER BRACKET
11
SPRING
12
STRIKER, CAST
13
WASHER, NYLON
14
6-32 NUT WITH NYLON INSERT, zINC PLATED
15
10-32 HEX HEAD MACHINE SCREW, 7/8" LONG, STAINLESS STEEL
16
10-32 PHILLIPS FLAT MACHINE SCREW, 1/2" LONG, STAINLESS STEEL
17
10-32 SLOTTED TRUSS HEAD MACHINE SCREW, 1/2" LONG, STAINLESS STEEL
18
10-32 SLOTTED TRUSS HEAD MACHINE SCREW, 3/4" LONG, STAINLESS STEEL
19
10-32 NUT WITH NYLON INSERT, zINC PLATED

6.9 DOOR GASKET REPLACEMENT

The cooking compartment door gaskets are made of a silicone
type rubber material, which is very durable, but is subject to
wear during normal daily operation. This gasket may start to
leak which will cause the steamer to malfunction. Should the
gasket begin to leak, it should be replaced as follows:
1.
Open the cooking compartment door.
2.
Remove the 6 screws from the door gasket mounting plate
on the inside of the door.
ITEM
FIGURE 6.10 SINGLE ELECTRIC POWERED STEAM GENERATOR ASSEMBLY
NO.
DESCRIPTION
1
ELECTRIC SEAM GENERATOR TANK
2
ELBOW, 1/8" mNPT TO 1/4" HOSE BARB, BRASS
3
ELBOW, 1/8" FNPT TO 1/4" HOSE BARB, BRASS
4
GASKET, OBROUND
5
HEATER: 208V
HEATER: 240V
HEATER: 480V
6
HEATER GASKET
7
HEATER MOUNTING PLATE
8
SPRAY NOzzLE
9
THERMAL FUSIBLE LINK
10
THERMOSTAT, N.O., 193
11
WATER LEVEL PROBE
12
1/4-20 NUT WITH NYLON INSERT, STAINLESS STEEL
13
1/4" WASHER, STAINLESS STEEL
6. MAINTENANCE
F
O
6.13
3.
Remove the door gasket mounting plate and the door gas-
ket.
4.
Install new door gasket (market Forge part Number 91-
5286) into the door.
5.
Refasten the door gasket mounting plate to the inside of
the door using the 6 screws.
NOTE: Remember that the lip on the door gasket mounting
plate must fit into the channel on the inside edge of the gasket
for a proper seal.
PART
qTY.
NO.
1
E91-5286
1
E91-5731
1
E91-5745
1
E91-5766
1
E91-5729
2
E08-2702
1
E91-5436
1
E91-5437
2
E08-5027
2
E91-5901
2
E08-4600
1
E09-1608
4
E10-0100
2
E08-3838
4
E08-3488
2
E08-3486
6
E10-1764
6
E10-1765
4
E08-3841
PART
qTY.
NO.
1
E91-5727
1
E08-5063
1
E08-5004
2
E91-5717
1
E08-6485
E08-6486
E08-6487
1
E91-8660
1
E91-5721
1
E08-5017
1
E91-6693
1
E10-8105
2
E08-6338
14
E08-3850
14
E08-4011

Advertisement

Table of Contents
loading

Table of Contents