Table of Contents
Advertisement
6.7 CONTROL PANEL ELECTRICAL SERVICE ACCESS
The control panel assembly is mounted onto the front of the
unit. It houses all of the controls and indicators which are used
to operate the cooker. In order to service any of the control
panel electrical components the control panel assembly muse
be removed from the front of the unit.
CAUTION: BE SURE TO DISCONNECT BOTH POWER SUP-
PLIES FROM THE UNIT BEFORE SERVICING ANY ELEC-
TRICAL COMPONENTS.
1.
Remove the 4 screws that fasten the control panel assem-
bly onto the front of the unit.
2.
Gently move the control panel assembly out away from
the unit. NOTE: Only move the control panel assembly
out as far as is necessary to access the rear of the as-
sembly. pULLING OUT THE CONTROL pANEL TOO FAR
CAN CAUSE DAmAGE BY pUTTING UNNECESSARY
STRAIN ON WIRES AND CONNECTIONS.
3.
Separate the control panel housing and indicator light
mounting brackets by removing the 4 nuts which hold them
together. Be careful not to lose the 1/4-20 nuts which are
used as spacers (1-per stud). This will allow total access
to all controls and indicators for service, repair, or replace-
ment. See Figure 6.3 on page 6.1.
6.8 DOOR ADJUSTMENT
The cooking compartment door alignment, door tension and
latch tension are pre-adjusted at the factory during assembly.
ITEM
NO.
DESCRIPTION
1
BUzzER
2
"CLEAN GENERATOR" INDICATOR LIGHT - ROUND NEON RED
3
"CONSTANT STEAM" BUTTON
4
"CONSTANT STEAM" INDICATOR LIGHT - ROUND NEON GREEN
5
CONTROL PANEL HOUSING ASSEMBLY
6
CONTROL PANEL LIGHT MOUNTING BRACKET
7
"HOLD" INDICATOR LIGHT - ROUND NEON AMBER
8
"MODE SELECT" SWITCH ASSEMBLY
9
"POWER ON" INDICATOR LIGHT
10
"POWER ON" INDICATOR LIGHT TINNERMAN RETAINER CLIP
11
POWER SWITCH
12
"READY" INDICATOR LIGHT - RECTANGULAR NEON GREEN
13
ROUND INDICATOR LIGHT RETAINER CLIP
14
"STEAM DEMAND" INDICATOR LIGHT - RECTANGULAR NEON RED
15
"STEAM ON" INDICATOR LIGHT - RECTANGULAR NEON GREEN
16
TERMINAL BLOCK
17
TIMER
18
TIMER KNOB
19
TIMER MOUNTING NUT
20
1/4-20 HEX NUT - zINC PLATED
21
6-32 NUT WITH NYLON INSERT - zINC PLATED
22
6-32 SLOTTED PAN HEAD MACHINE SCREW - zINC PLATED 1/2" LONG
23
8-32 NUT WITH NYLON INSERT - zINC PLATED
6. MAINTENANCE
FIGURE 6.7 CONTROL PANEL ASSEMBLY
During normal usage, these should not need any attention.
Note that when the cooking compartment doors are revered, as
described in section 2.3, the doors will need to be aligned and
the door latch tension will need to be adjusted (the door handle
will not need adjustment when the door is reversed).
6.8.1 DOOR ALIGNMENT
The cooking compartment doors are pre-aligned at the factory
during assembly, and should not need adjusting unless they are
reversed. Should the doors need realignment, the procedure is
as follows:
1.
Open the cooking compartment door.
2.
Loosen all 4 bolts (2-per hinge) which mount the upper and
lower hinge brackets to the face of the unit using a 5/16"
wrench. DO NOT REMOVE THE BOLTS.
3.
Begin to retighten the 4 bolts so that they are snug against
the face of the unit. DO NOT COMPLETELY TIGHTEN
THE BOLTS.
4.
Slowly ease the cooking compartment door closed until it
is latched.
5.
The cooking compartment door can now be raised, low-
ered, and/or rotates into position by bumping it with the
palm of your hand or a small rubber mallet.
6.
First check the alignment at the front of the door by making
sure that the striker in the door is centered with the latch
mechanism on the front of the door.
6.9
PART
qTY.
NO.
1
E10-6682
1
E08-6530
1
E08-6526
1
E08-6529
1
E91-5743
1
E91-5688
1
E08-6531
1
E08-6525
1
E08-6523
1
E08-6523
1
E08-6524
1
E08-6527
3
E08-6527
1
E08-6528
1
E08-6527
1
E08-6518
1
E10-6291
1
E08-3826
1
E10-6291
4
E08-3844
2
E08-3838
2
E08-3438
4
E08-3839
Advertisement
Table of Contents
