Omron E5CC Communications Manual page 99

Address
Parameter name
Four-byte Two-byte
mode mode
0500 2500 Operation/Adjustment
Protect
0502 2501 Initial
Setting/Communications
Protect
0504 2502 Setting Change Protect
0506 2503 PF Key Protect
0508 2504 Move to Protect Level
050A 2505 Password to Move to
Protect Level
050C 2506 Parameter Mask Enable
050E 2507 Changed Parameters
Only
0600 2600 Manual MV
0602 2601 Set Point
0604 2602 Remote SP Monitor
0608 2604 Heater Current 1 Value
Monitor
060A 2605 MV Monitor (Heating)
060C 2606 MV Monitor (Cooling)
060E 2607 Valve Opening Monitor
* You can use this selection only with the E5EC-PR@-8@@ or E5AC-PR@-8@@. (The Digital Controller must be
manufactured in August 2014 or later (version 2.2 or higher).)
E5@C Digital Temperature Controllers Communications Manual (H175)
5 Communications Data for Modbus
Setting (monitor) value
H'00000000 (0): No restrictions in operation and adjustment levels
H'00000001 (1): Move to adjustment level is prohibited.
H'00000002 (2): Display and change of only "PV" and "PV/SP"
parameters is allowed.
H'00000003 (3): Display of only "PV" and "PV/SP" parameters is
allowed.
H'00000000 (0): Move to initial setting/communications setting
level is allowed. (Move to advanced function
setting level is displayed.)
H'00000001 (1): Move to initial setting/communications setting
level is allowed. (Move to advanced function
setting level is not displayed.)
H'00000002 (2): Move to initial setting/communications setting
level is prohibited.
H'00000000 (0): OFF (Changing of setup on controller display is
allowed.)
H'00000001 (1): ON (Changing of setup on controller display is
prohibited.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
Standard Models
Standard control:
H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating and cooling control:
H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position-proportional Models
Close position-proportional control with the Direct Setting of
Position Proportional MV parameter set to ON:
H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
SP lower limit to SP upper limit
Remote SP lower limit −10% FS to Remote SP upper limit +10% FS
H'00000000 to H'00000226 (0.0 to 55.0)
Standard control: H'FFFFFFCE to H'0000041A
(−5.0 to 105.0)
Heating and cooling control: H'00000000 to H'0000041A
(0.0 to 105.0)
H'00000000 to H'0000041A (0.0 to 105.0)
H'FFFFFF9C to H'0000044C (−10.0 to 110.0): Measured opening
H'00000000 to H'000003E8 (0.0 to 100.0): Estimated opening*
Level
Protect
5
Manual
control
Operation
5 - 3