Omron E5CC Communications Manual page 205

With the default settings, the following parameters are set for the download areas.
No.0 No.1
DM15 DM45
DM16 DM46
DM17 DM47
DM18 DM48
DM19 DM49
DM20 DM50
DM21 DM51
DM22 DM52
DM23 DM53
DM24 DM54
DM25 DM55
DM26 DM56
DM27 DM57
DM28 DM58
DM29 DM59
(2) We will initialize the download areas with the set values from the E5CC Controllers.
The download areas have not been initialized, so we will initialize them with the set values
from the E5CC Controllers.
Double-click DM15 (Request Flag) on the Batch Monitor Dialog Box, enter 2 (Initialize
Download Areas), and press the Enter Key.
(3) We will confirm that the download areas have been initialized.
When initialization is completed, DM0 (Response Flag) will change to 1 (Normal End) and
DM15 (Request Flag) will automatically change to 1 (Enable Writing). Check the download
area to see if it has been initialized to the values given in the above table.
Confirm this for the No. 1 and No. 2 Controllers as well.
(4) We will change the set point for the No. 0 Controller.
Double-click DM17 (Set Point) on the Batch Monitor Dialog Box, enter 100 (64 hex) as the
value, and press the Enter Key. Confirm that DM0 (Request Flag) remains at 1 (Enable
Writing) and that the SV Display on the No. 0 Controller changes to 100.
Confirm this for the No. 1 and No. 2 Controllers as well.
 Stopping the E5CC Controllers
(1) We will run the No. 0 Controller.
Change the RUN/STOP parameter (r-s) in the operation level of the E5CC to RUN (run).
For a Controller with event inputs, the Event Input 2 Assignment parameter (ev-2) in the
initial setting level is set to RUN/STOP (stop), so the RUN/STOP parameter will not be dis-
played. Change the Event Input 2 Assignment parameter to NONE (none), and then
change the RUN/STOP parameter to RUN.
(2) We will switch the No. 0 Controller to STOP.
Change the display format to Hexadecimal 16 bit on the Batch Monitor Dialog Box. Then,
confirm that DM15 (Request Flag) is 1 (Enable Writing), double-click DM16 (Operation
Command Code), enter 0101 hex (Stop), and press the Enter Key.
DM16 will change to 0, DM0 (Response Flag) will remain at 1 (Enable Writing), and "STOP"
will be displayed on the No. 0 Controller.
Confirm this for the No. 1 and No. 2 Controllers as well.
For details on other operation command codes, refer to 6-3-4 Operation Command Codes.
E5@C Digital Temperature Controllers Communications Manual (H175)
No.2 Parameter
DM75 Request Flag (fixed)
DM76 Operation Command Code (fixed)
DM77 Set Point
DM78 Proportional Band
DM79 Integral Time
DM80 Derivative Time
DM81 Alarm Value 1
DM82 Alarm Value Upper Limit 1
DM83 Alarm Value Lower Limit 1
DM84 Alarm Value 2
DM85 Alarm Value Upper Limit 2
DM86 Alarm Value Lower Limit 2
DM87 Heater Burnout Detection 1
DM88 Process Value Input Shift
DM89 SP Ramp Set Value
6 Programless Communications
Value (E5CC default settings)
1 (0001 hex)
0 (0000 hex)
0 (0000 hex)
80 (0050 hex)
233 (00E9 hex)
40 (0028 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
0 (0000 hex)
6
6 - 91