Omron E5CC Communications Manual page 108

5 Communications Data for Modbus
Address
Parameter name
Four-byte Two-byte
mode mode
0E48 2E24 Extraction of Square Root
Enable
0E60 2E30 Travel Time
0F00 2F00 Alarm 1 Type
0F02 2F01 Alarm 1 Latch
0F04 2F02 Alarm 1 Hysteresis
0F06 2F03 Alarm 2 Type
0F08 2F04 Alarm 2 Latch
0F0A 2F05 Alarm 2 Hysteresis
0F0C 2F06 Alarm 3 Type
0F0E 2F07 Alarm 3 Latch
0F10 2F08 Alarm 3 Hysteresis
0F12 2F09 Alarm 4 Type
0F14 2F0A Alarm 4 Latch
0F16 2F0B Alarm 4 Hysteresis
0F18 2F0C Standby Sequence Reset
0F1A 2F0D Auxiliary Output 1 Open
in Alarm
5 - 12
Setting (monitor) value
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'000003E7 (1 to 999)
H'00000000 (0): Alarm function OFF
H'00000001 (1): Upper and lower-limit alarm
H'00000002 (2): Upper-limit alarm
H'00000003 (3): Lower-limit alarm
H'00000004 (4): Upper and lower-limit range alarm
H'00000005 (5): Upper and lower-limit alarm with standby sequence
H'00000006 (6): Upper-limit alarm with standby sequence
H'00000007 (7): Lower-limit alarm with standby sequence
H'00000008 (8): Absolute-value upper-limit alarm
H'00000009 (9): Absolute-value lower-limit alarm
H'0000000A (10): Absolute-value upper-limit alarm with standby
sequence
H'0000000B (11): Absolute-value lower-limit alarm with standby
sequence
H'0000000C (12): LBA (Loop Burnout Alarm)
H'0000000D (13): PV change rate alarm
H'0000000E (14): SP absolute-value upper-limit alarm
H'0000000F (15): SP absolute-value lower-limit alarm
H'00000010 (16): MV absolute-value upper-limit alarm
H'00000011 (17): MV absolute-value lower-limit alarm
H'00000012 (18): RSP absolute-value upper-limit alarm *
H'00000013 (19): RSP absolute-value lower-limit alarm *
* Valid only with a remote SP input.
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'0000270F
(0.1 to 999.9 for temperature input)
(0.01 to 99.99 for analog input)
H'00000000 to H'00000013 (0 to 19)
Note: Same settings as the Alarm 1 Type. However, the LBA (loop
burnout alarm) cannot be set.
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'0000270F
(0.1 to 999.9 for temperature input)
(0.01 to 99.99 for analog input)
H'00000000 to H'00000013 (0 to 19)
Note: Same settings as the Alarm 1 Type. However, the LBA (loop
burnout alarm) cannot be set.
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'0000270F
(0.1 to 999.9 for temperature input)
(0.01 to 99.99 for analog input)
H'00000000 to H'00000013 (0 to 19)
Note: Same settings as the Alarm 1 Type. However, the LBA (loop
burnout alarm) cannot be set.
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'0000270F
(0.1 to 999.9 for temperature input)
(0.01 to 99.99 for analog input)
H'00000000 (0): Condition A
H'00000001 (1): Condition B
H'00000000 (0): Close in alarm
H'00000001 (1): Open in alarm
E5@C Digital Temperature Controllers Communications Manual (H175)
Level
Initial setting
Advanced
function
setting
Initial setting
Advanced
function
setting
Initial setting
Advanced
function
setting
Initial setting
Advanced
function
setting
Initial setting
Advanced
function
setting