Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bdcom S5612
Summary of Contents for Bdcom S5612
- Page 1 S5612 Hardware Installation Manual...
-
Page 2: Table Of Contents
2.3.3 Cabinet Configuration ....................7 2.3.4 Power Requirements ....................8 2.4 Installation Tools and Device ....................8 Chapter 3 Installing the S5612 Switch ....................9 3.1 Installation Flow of S5612 ....................9 3.2 Installing the Machine Box of the Switch ................9 3.2.1 Installing the Machine Box on the Desk .............. - Page 3 Table of Contents 3.3.3 Connecting Gigabit Ethernet TX Ports ..............12 3.4 Checking After Installation ....................13 Chapter 4 Maintaining Switch ......................15 4.1 Opening the Machine Box ....................15 4.2 Closing Machine Box ......................16 Chapter 5 Hardware Fault Analysis ....................17 5.1 Fault Separation .........................
-
Page 4: Chapter 1 S5612 Introduction
The section describes the characteristics and parameters of S5612 and gives an overview of S5612. 1.1 Appearance Description for Standard Configuration The built-in ports of S5612 are: 8 gigabit Ethernet RJ45 ports, 12 10G SFP+ ports, 1 Console port. See table 1-1. Table 1-1 Attributes of the built-in port... -
Page 5: S5612 Systematic Characteristic Parameters
8 Gigabit TX ports 8 Gigabit TX ports SFP+ 10G SFP+ ports 12 10G SFP+ ports Figure 1-2 Back template of the S5612 switch Table 1-3 Parts at the back template of the S5612 switch Abbrev. Name Description AC power socket AC100～240V. - Page 6 S5612 Hardware Installation RFC 1157 SNMP v1/v2 Network RFC 1213 MIB II management standard RFC 1757 RMON 1,2,3,9 Flash Memory: 16M Bytes Memory SDRAM: 512MBytes； 8 10/100/1000BASE-T ports Standard configuration 12 10G SFP+ ports 1 Console port Dimensions mm 442.50×315×44 (W×D×H)
-
Page 7: Rohs Description
S5612 Hardware Installation 1.3 ROHS Description - 4 -... -
Page 8: Chapter 2 Installation Preparation
Similar to other electronic products, the semiconductor chip easily gets damaged if you power on or off abruptly and frequently. To restart up the switch of S5612, you have to open the power on-off after the power is cut down for three to five seconds. -
Page 9: Safety Principles For Live Working
S5612 Hardware Installation Read the installation guide carefully before you operate the system. Only professionals are allowed to install or replace the switch. Pull out the AC power socket and close the direct-current power before operating on the machine box or working beside the power source. -
Page 10: Electrostatic Discharge Damage Prevention
S5612 Hardware Installation 2.2.4 Electrostatic Discharge Damage Prevention Electrostatic discharge may damage devices and circuits. Improper treatment may cause the switch to malfunction completely or discontinuously. Move or locate the devices according to the measures of electrostatic discharge prevention, ensuring the machine box connects the ground. Another measure is to wear the static-proof hand ring. -
Page 11: Power Requirements
2.4 Installation Tools and Device The tools and devices to install the S5612 switch are not provided by the S5612 switch. You yourself need to prepare them. The following are the tools and devices needed for the typical installation of the S5612 switch: ... -
Page 12: Chapter 3 Installing The S5612 Switch
Installing the machine box on the cabinet 3.2.1 Installing the Machine Box on the Desk The S5612 switch can be directly put on the smooth and safe desk. Note: Do not put things weighing 4.5 kg or over 4.5 kg on the top of the switch. -
Page 13: Installing The Machine Box On The Cabinet
RJ45 plug. After you connect the console port to the serial port of PC through a console cable, you can configure and monitor the switch of S5612 by running a terminal emulation software, such as super Windows terminal. The cable is provided according to the host. - Page 14 The other end of the console cable is DB9, and the RJ45 plug is put into the socket of the console port on the S5612 switch. Figure 3-4 The inner connection of the 1-to-8 RJ45 cable (RLC0301). Figure 3-5 Connecting the console port of S5612 and computer Table 3-1 Pins of the console port Name...
-
Page 15: Connecting 10G Ethernet Sfp+ Ports
No connect Note: The console port of S5612 does not support traffic control. Therefore, you must set the option data traffic control to none when you configure the switch with the super terminal. Otherwise, the single-pass problem will arise on the super terminal. -
Page 16: Checking After Installation
S5612 can adopt five types of direct-through/cross network cables when it connects other Ethernet terminals. Figure 3-8 Connecting the 1000Base-TX port and other Ethernet terminals Caution: The switch shown in figure 3-8 does not represent the material S5612. Table 3-1 Pins of Gigabit RJ45 Pin Name... - Page 17 S5612 Hardware Installation Check whether the connected power meets the power requirements of the switch. Check whether the grounding line is correctly connected. Check whether the switch is correctly connected to other terminal devices. - 14 -...
-
Page 18: Chapter 4 Maintaining Switch
S5612 Hardware Installation Chapter 4 Maintaining Switch Caution: Before opening the machine box, make sure that you have released the static you carried and then turn off the power on-off of the switch. Before operating any step in Appendix B, read the section “Safety Advice”. -
Page 19: Closing Machine Box
S5612 Hardware Installation Caution: The switch shown in the above figure does not represent the material S5612. When the cover is opened, put it aside. The mainboard of the system appears. Note: After taking off the cover, put it horizontally and avoid it to be crushed or collided. -
Page 20: Chapter 5 Hardware Fault Analysis
9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control. 5.2 Indicator Description The LED indicator shows that the switch is running. The following table shows the indicators of the S5612 switch and their description: - 17 -... - Page 21 S5612 Hardware Installation Abbrev. Name Description When the switch is powered on, Power indicator the indicator is on. When the indicator is always on, the system is being started up. System indicator When the indicator flickers, the system works well.