Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bdcom S2928F
Summary of Contents for Bdcom S2928F
- Page 1 S2928F Hardware Installation Manual...
-
Page 2: Table Of Contents
Table of Contents Table of Contents Chapter 1 S2928F Introduction........................1 1.1 Standard Configuration........................1 1.2 Characteristic Parameters of S2928F................... 2 1.3 ROHS Description..........................3 Chapter 2 Installation Preparation........................ 5 2.1 Cautions............................. 5 2.2 Safety Advice.............................5 2.2.1 Safety Principles........................5 2.2.2 Safety Notices........................5 2.2.3 Safety Principles for Live Working.................. - Page 3 Table of Contents Chapter 4 Maintaining the Switch.......................16 4.1 Opening the Chassis........................17 4.2 Closing Chassis..........................17 4.3 System Memory Upgrade......................18 4.3.1 SDRAM Expansion......................18 Chapter 5 Hardware Fault Analysis......................19 5.1 Fault Separation..........................20 5.1.1 Faults Relative with Power and Cooling System............20 5.1.2 Faults Relative with Port, Cable and Connection............20 5.2 LED Description..........................20 - 2 -...
-
Page 4: Chapter 1 S2928F Introduction
The section describes the characteristics and parameters of S2928F and gives an overview of S2928F. 1.1 Standard Configuration The built-in ports of S2928F are: 8 gigabit combo ports, 16 gigabit optical ports, 4 10GE optical ports and 1 console port. See table 1-1. Table 1- 1 Attributes of the built-in ports... -
Page 5: Characteristic Parameters Of S2928F
If the switch is powered on, Power indicator the indicator is on. Console Console port Manages the switch locally. Figure 1-2 Back template of S2928F switch Table 1-3 Parts at the back template of S2928F switch Abbrev. Name Description AC power socket AC100~240V. Grounding column The grounding must be fine. -
Page 6: Rohs Description
S2928F Hardware Installation Manual RFC 1058 RIP RFC 1723 RIP v2 IP routing protocol standard RFC 1583 OSPF v2 RFC 1157 SNMP v1/v2 RFC 1213 MIB II Network management standard RFC 1757 RMON 1,2,3,9 Flash Memory: 16M Bytes Memory SDRAM: 512M Bytes;... - Page 7 S2928F Hardware Installation Manual - 4 -...
-
Page 8: Chapter 2 Installation Preparation
Similar to other electronic products, the semiconductor chip easily gets damaged if you power on and off abruptly and frequently. To restart up the switch of S2928F, you have to open the power on-off after the power is cut down for three to five seconds. -
Page 9: Safety Principles For Live Working
S2928F Hardware Installation Manual Pull out the AC power socket and close the direct-current power before operating on the machine box or working beside the power source. The final configuration of products must comply with relative national laws and regulations. -
Page 10: Requirements For Common Locations
S2928F Hardware Installation Manual Move or locate the devices according to the measures of electrostatic discharge prevention, ensuring the chassis connects the ground. Another measure is to wear the static-proof hand ring. If there is no hand ring, use the metal clip with the metal cable to clip the unpainted metal part of the chassis. -
Page 11: Power Requirements
2.4 Installation Tools and Device The tools and devices to install the S2928F switch are not provided by the S2928F switch. You yourself need to prepare them. The following are the tools and devices needed for the typical installation of the S2928F switch: ... -
Page 12: Chapter 3 Installing S2928F Switch
S2928F Hardware Installation Manual Chapter 3 Installing S2928F Switch Caution: Only professionals are allowed to install or replace the devices of the router. - 9 -... -
Page 13: Installation Flow Of S2928F
Installing the Chassis on the Cabinet 3.2.1 Installing the Chassis on the Desk The S2928F switch can be directly put on the smooth and safe desk. Note: Do not put things weighing 4.5 kg or over 4.5 kg on the top of the switch. -
Page 14: Connecting The Port
PC through a console cable, you can configure and monitor the switch of S2928F by running a terminal emulation software, such as super Windows terminal. The cable is provided according to the host. The communication parameters of the terminal serial port can be set to a rate of 9600bps, eight data bits, one stop bit, no sum check bit and traffic control. - Page 15 Otherwise, the single-pass problem will arise on the super terminal. The cable is used to connect the console port of the S2928F switch and the outside console terminal device. One end is mini USB plug and the other end is 9-hole plug (DB9).
-
Page 16: Connecting The 10Ge Ethernet Sfp+ Ports
3.3.2 Connecting the 10GE Ethernet SFP+ Ports The S2928F switch has 4 10GE SFP+ ports and 4 corresponding indicators TE1~TE4. You can insert the SFP+ optical module into the port and then connect the module to other Ethernet terminal devices through the optical fiber if you want to use the SFP+ port. - Page 17 S2928F Hardware Installation Manual Figure 3-6 The RJ45 connector of the console port Because 8 10/100Base-T ports of S2928F support the MDI/MDIX auto-identification of the cable, S2928F can adopt five classes of direct-through/crossover network cables when it connects to other Ethernet terminals.
-
Page 18: Checkup After Installation
S2928F Hardware Installation Manual Sending/receiving the paraphase of the data 1 TP1- Sending/receiving the normal phase of data 3 TP3+ Sending/receiving the paraphase of the data 3 TP3- The direct-through or cross network cable has the function of auto-identification, so the five classes of direct-through/cross network cables can be used to connect other Ethernet devices. -
Page 19: Chapter 4 Maintaining The Switch
S2928F Hardware Installation Manual Chapter 4 Maintaining the Switch Caution: Before opening the chassis, make sure that you have released the static you carried and then turn off the power on-off of the switch. Before operating any step in Appendix B, read the section "SAFETY ADVICE”. -
Page 20: Opening The Chassis
S2928F Hardware Installation Manual 4.1 Opening the Chassis This section describes how to open the cover of the switch, required tools and operation methods. Caution: When the power cable still connects the power supply, do not touch it. When you open the cover the switch, you may use the following tools: These tools are: ... -
Page 21: System Memory Upgrade
S2928F Hardware Installation Manual See the following figure. When the cover and the bottom are closely tied, let the cover slide the slot of the front template at the bottom. Nail the bolt and screw it tightly with the screwdriver. -
Page 22: Chapter 5 Hardware Fault Analysis
S2928F Hardware Installation Manual Chapter 5 Hardware Fault Analysis The part describes how to remove the fault from the switch. - 19 -... -
Page 23: Fault Separation
If the console port does not work after the system is started up, check whether the console port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control. 5.2 LED Description S2928F switch indicators and their usage: Abbrev. Name Description If the indicator is always on, the system is being started up. - Page 24 S2928F Hardware Installation Manual If the switch is powered on, the indicator Power LED is on. If the fan works normally, the indicator is Fan indicator If the indicator is always on, the link on the port is normal. LINKACT...
Need help?
Do you have a question about the S2928F and is the answer not in the manual?
Questions and answers