General Information; Dear Customer; Grounding Instructions; Unpacking The Machine - Mytee Speedster LTD3 Instructions Manual

GENERAL INFORMATION

Dear Customer:

Congratulations on the purchase of your new LTD Speedster® extractor.
As technology continues to develop you can work confidently knowing
that both Mytee Products Inc. and its employees are equally dedicated to
developing with the industry and its advances.
Like any other piece of machinery or technology, the LTDs also requires
the proper maintenance and care to keep the product working over
extended use. Neglecting your machine, abusing it or not operating it
properly can void its warranty and prevent the machine from performing to
the quality and standard you'd expect out of the Mytee Products Inc. line.
If you have any warranty concerns or questions, please review this manual
thoroughly or do not hesitate to contact your distributor. If there are ques-
tions regarding maintenance, replacement or ordering parts please contact
an authorized Mytee Products Inc. Service Center. To see an updated list
please visit our website at http://www.mytee.com/support/find-distribu-
tors/
Before using your Mytee Product, please read this manually thoroughly.
Sincerely,
Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical shock. This ma-
chine is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code and ordinances.
Do not remove ground pin; if missing, replace plug before use.
Improper installation of the equipment-grounding conductor can result
in a risk of electric shock. Be sure to check with a qualified electrician
or service person if you are in doubt as to whether the outlet is properly
grounded. If the plug will not fit in the outlet do not modify either the plug
nor the machine's cord, instead have a proper outlet installed by a quali-
fied technician.
This machine is for use on a nominal 120-volt circuit and with a grounding
plug similar to the one in Figure 1 below. If a proper outlet is not available,
follow the illustrations of Figure 2 & 3 to install a temporary-grounding
plug. This temporary work-around should be used only until a proper outlet
(Figure 1) can be installed by a qualified electrician. When and if this type
of adapter is employed, screw the adapter's extended tab into place with
a metal screw. However, grounding adapters are not approved for use in
Canada.
Again, be sure to check the grounding pin for damages and replace if
necessary.
The Green, or Green-Yellow, wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to only the grounding pin.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Grounding Pin Grounded Outlet Box
Figure 1
Adapter
Metal
Screw
Tab for Grounding
Screw
Figure 2 Figure 3

Parts and Service

Please contact a Mytee service personnel or Mytee authorized Service
Center using Mytee original replacement parts and accessories for repairs
are needing to be performed. When and if calling Mytee for support,
please have your Model and Serial Number available for faster assistance.

Name Plate

The Model and Serial Number are located on the lower half of the back
of the machine near the power plugs and will be required for ordering
replacement parts. You can use the space provided on the front of this
manual to note down both for future referencing.

Unpacking the Machine

1. When your new machine is delivered, please carefully inspect both the
shipping carton and the machine for damages. If damage is evident, save
both the shipping carton and machine so that the delivering carrier can
inspect it. Contact the carrier immediately to le a freight claim if there has
been any damage.
2. Install the Nylon-mesh pump-out pre-filter, packaged in the accessories
bag, into the interior base of the recovery tank. Slide the metal ring section
of the bag over the cylindrical main pump-out filter, such that the Nylon
bag covers the entire stainless steel mesh of the main pump-out filter.
Slide the ring to the base of the main filter. For identification, bag is shown
here.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to
protect personnel and property.
Is used to warn of immediate hazards that will cause severe personal
injury or death.
Is used to call attention to a situation that could cause severe personal
injury.
Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property. When using an electri-
cal appliance, basic precautions should always be followed, including the
following: Read all instructions before using this machine. This product is
intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer's recom-
mended attachments.
3. Always unplug power cord from electrical outlet before attempting any
adjustments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the
2