Mytee SPEEDSTER 1000DX Instruction Manual & Safety Manual

Mytee SPEEDSTER 1000DX Instruction Manual & Safety Manual

Cold water, hot water
Hide thumbs Also See for SPEEDSTER 1000DX:

Advertisement

mytee
mytee
PRODUCTS, INC.
Instruction
Manual
&
Safety Guide
Cold Water Models
1000DX
1000DX-200
7
1005DX
SPEEDSTER
Hot Water Models
1001DX
1001DX-200
1003DX

Advertisement

Table of Contents
loading

Summary of Contents for Mytee SPEEDSTER 1000DX

  • Page 1 Cold Water Models 1000DX Hot Water Models 1000DX-200 mytee mytee 1005DX 1001DX PRODUCTS, INC. 1001DX-200 1003DX Instruction Manual & Safety Guide SPEEDSTER...
  • Page 3: Table Of Contents

    Please read and review it carefully before using the equipment for the first time. It also contains information on optional accessories, cleaning tips, and a troubleshooting guide. We here at Mytee Products would like to welcome you to the team, and wish you the best for the future. TABLE OF CONTENTS...
  • Page 4: Safety Precautions

    SAFETY PRECAUTIONS This machine is intended for commercial use. It is designed to clean carpet and upholstery in an indoor environment and is not constructed for any other use. Use only recommended cleaning solutions and accessory tools. All operators must read, understand and practice the following safety precautions. The following safety alerts symbols are used throughout this manual as indicated in their description: WARNING: To warn of hazards or unsafe practices which could result in severe personal...
  • Page 5: Warranty

    Mytee or a Mytee authorized distributor or service center to describe the claim and to re- ceive and follow instructions for documenting and resolving the claim.
  • Page 6: Unpacking The Machine

    OPTIONAL ACCESSORIES The following accessories and tools are available for this unit, and can be purchased separately at your local Mytee dealer. You can find more information on any of them at www.mytee.com 8400 - 3” Stainless Steel Upholstery Tool 8100 - 15’...
  • Page 7 OPTIONAL ACCESSORIES 8350EZ – 12” Single Jet, 8300EZ – 12” Dual Jet, Floor Wand S- Bend Floor Wand SM100 – Spinmaster Rotary Extractor 3601 – System Maintainer...
  • Page 8: Safety Labels

    SAFETY LABELS The safety labels appear on the machine in the locations indicated. Replace labels if they become damaged or cannot be read. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tank(s). Flammable materials or reactive metals can cause explosion or fire. WARNING LABEL- Located on back.
  • Page 9: Setup

    SETUP PRE-OPERATION 1. Vacuum carpet and upholstery and remove other debris. 2. Perform MACHINE SETUP procedures. 3. Inspect power cord for damage. 1. Open lid of solution tank. Fill solution tank with water or approved cleaning agent. WARNING: Flammable materials can cause an explosion or fire.
  • Page 10: Operation

    OPERATION 7. Turning machine on. A. Turn pump switch on. PUMP B. Pull up on power prime lever for 30 seconds. This will prime the pump. NOTE: STEP 7B IS FOR 1000DX-200, 1001DX-200, 1003DX, & 1005DX ONLY C. Pull up on wand lever to release air in the line. Hold lever until you have a steady flow of water coming out of the wand.
  • Page 11: Tips

    TIPS 1. Work away from outlet and power cord to prevent cord damage. 2. Use a recommended foam control solution in the recovery tank to prevent vacuum motor damage. Periodically check for excessive foam buildup in solution tank, and recovery tank. 3.
  • Page 12 WEEKLY MAINTENANCE (EVERY 20 HOURS OF OPERATION) 1. Flush solution system with Mytee system maintainer to dissolve normal chemical buildup. a. Pour 7.5L (2 gal) of hot water 60°C (140°F) into solution tank. Add Mytee system maintainer according to mixing instructions on bottle FOR SAFETY: When using machine, follow mixing and handling instructions on chemical containers.
  • Page 13 SOLUTION: Remove filters and rinse clean with water. PROBLEM: Heater is blocked with hard water deposits. SOLUTION: Flush out heaters with Mytee Products, Inc. system maintainer solution PROBLEM: Brass check valve is stuck. SOLUTION: Replace with new check valve. PROBLEM: Pump wire has become disconnected.
  • Page 14 PARTS DESCRIPTION WHERE USED PART NUMBER Vacuum motor 1003DX 3 stage 115v 1005DX C302 1000DX ( -200 ) Vacuum motor 1001DX ( -200 ) 2 stageHP, 115v C301 Pump, 450 psi 1003DX 1005DX C313 Pump, 100 psi 1000DX 1001DX C305 Pump, 250 psi 1000DX-200 1001DX-200...
  • Page 16 PRODUCTS, INC. Mytee Products 13655 Stowe Drive Poway, CA 92064 (858) 679-1191 www.mytee.com...

Table of Contents