Mytee Speedster LTD3 Instructions Manual
  1. Manuals
  2. Brands
  3. Mytee Manuals
  4. Floor Machine
  5. Speedster LTD3
  6. Instructions manual

Mytee Speedster LTD3 Instructions Manual

Hide thumbs Also See for Speedster LTD3:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instructions, User Manual
7
Instructions for
Speedster
Please read before use.
Register your product
at http://www.mytee.
com/support/register
General & Maintenance Information p. 2
LTD3 p. 6
LTD5 p. 13
LTD12 p. 20
6
LTD3, LTD5 & LTD12
®
13655 Stowe Dr., Poway, CA 92064
5
1
4
3
Model #
Serial #
Form # ADP-SLTD
9-17
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
REV.
OD
UNLESS O
DIMENSI
TOLERAN
ANGULA
ONE PLA
TWO PLA
THREE PL
MATERIAL
FINISH

Advertisement

Table of Contents
loading

Related Manuals for Mytee Speedster LTD3

Summary of Contents for Mytee Speedster LTD3

  • Page 1 PROPRIETARY AND CONFIDENTIAL 13655 Stowe Dr., Poway, CA 92064 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS...

  • Page 2: General Information

    You can use the space provided on the front of this the quality and standard you’d expect out of the Mytee Products Inc. line. manual to note down both for future referencing.

  • Page 3: After Use

    Clean machine with all-purpose cleaner 19. Do not leave operating unattended. and cloth. Check spray nozzles. Preparation Flush solution system with Mytee System ® Maintainer. 1. Remove furniture and other items from the area you are going to clean. Remove and float shut-off screen from 2.

  • Page 4: Troubleshooting

    3. Jets clogged, remove jet and flush clean. 4. Filters clogged, remove filters and rinse clean with water. Machine Weight 135 lbs. 5. Heater is blocked; flush out with Mytee’s® System Maintainer. Machine 6. If brass check valve is stuck, replace valve. 28” x 18.5” x 39”...
  • Page 5 Q: Is there anything I can do to increase the expected life of my machine? A: Running the vacuum motors with the tank empty and lid off will allow excess moisture in the vacs to dry off. You should also run Mytee’s® System Maintainer through the system to keep the hoses, pump, and...
  • Page 6 SPEEDSTER® LTD3 SPEEDSTER LTD3 FRONT SPEEDSTER LTD3 BACK ® ® 1. Switch Plate 7. Pressure Regulator 12. Push Handle 18. Auto Fill/Pump-Out Hose 2. Pressure Gauge 8. Side Vent 13. Recovery Tank Connections 3. Solution Tank Lid 9. Recovery Tank 14.

  • Page 7: Filling The Solution Tank

    SPEEDSTER® LTD3 VACUUM AND SOLUTION HOSE CONNECTIONS SWITCH PLATE Vac 1 Vac 2 Pump Pump Heater To use vacuum, turn on Vac 1 and Vac 2. To use pump, turn on Pump. To use pump-out, turn on Pump-Out switch. To use Heater, Attach female end of a solution hose to a wand or tool and the turn on Heater.
  • Page 8 SPEEDSTER® LTD3 AUTO-FILL & PUMP-OUT CONECTIONS Auto-fill: Connect standard garden hose from water source to LTD AUTO-FILL auto-fill connection. Turn on the water source and let the tank begin to fill. It will shut off when the water level reaches the float switch in the solution tank.

  • Page 9: Emptying The Recovery Tank

    BY PASS FILTER The LTD’s internal filters must be cleaned regularly and are lo- Weekly flushing of the solution system with Mytee® System cated in the locations listed in the above diagram. Twist the filters Maintainer helps keep lines clean and prevents chemical build-up, to remove them then clean and replace in original locations.
  • Page 10 SPEEDSTER® LTD3 PARTS & PRICING Part prices are subject to change.
  • Page 11 SPEEDSTER® LTD3 PARTS & PRICING...
  • Page 12 SPEEDSTER® LTD3 WIRING DIAGRAM...
  • Page 13 THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. DRAWING IS THE SOLE PROPERTY OF LTD 5 MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH 16. Rear Vacuum Exhaust 22. Side Vent WITHOUT THE WRITTEN PERMISSION OF 4.
  • Page 14 SPEEDSTER® LTD5 VACUUM AND SOLUTION HOSE CONNECTIONS SWITCH PLATE Vac 1 Vac 2 Pump Pump Attach female end of a solution hose to a wand or tool and the To use vacuum, turn on Vac 1 and Vac 2. To use pump, turn on male end to the LTD’s QD.
  • Page 15 SPEEDSTER® LTD5 AUTO-FILL & PUMP-OUT CONECTIONS AUTO-FILL Auto-fill: Connect standard garden hose from water source to LTD auto-fill connection. Turn on the water source and let the tank begin to fill. It will shut off when the water level reaches the float switch in the solution tank.
  • Page 16 BY PASS FILTER The LTD’s internal filters must be cleaned regularly and are lo- Weekly flushing of the solution system with Mytee® System cated in the locations listed in the above diagram. Twist the filters Maintainer helps keep lines clean and prevents chemical build-up, to remove them then clean and replace in original locations.
  • Page 17 SPEEDSTER® LTD5 PARTS & PRICING Part prices are subject to change.
  • Page 18 SPEEDSTER® LTD5 PARTS & PRICING...
  • Page 19 SPEEDSTER® LTD5 WIRING DIAGRAM...
  • Page 20 4. Pressure Regulator 11. Solution Lid DRAWING IS THE SOLE PROPERTY OF 16. Rear Vacuum Exhaust Connections LTD 12 MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
  • Page 21 SPEEDSTER® LTD12 VACUUM AND SOLUTION HOSE CONNECTIONS SWITCH PLATE Vac 1 Vac 2 Pump Pump Attach female end of a solution hose to a wand or tool and the To use vacuum, turn on Vac 1 and Vac 2. To use pump, turn on male end to the LTD’s QD.
  • Page 22 SPEEDSTER® LTD12 AUTO-FILL & PUMP-OUT CONECTIONS AUTO-FILL Auto-fill: Connect standard garden hose from water source to LTD auto-fill connection. Turn on the water source and let the tank begin to fill. It will shut off when the water level reaches the float switch in the solution tank.
  • Page 23 TIGHTEN To remove any remaining water in the solution tank, located on Weekly flushing of the solution system with Mytee System Main- the back of the unit is a cap, twist and remove cap to tainer helps keep lines clean and prevents chemical build-up, empty tank.
  • Page 24 SPEEDSTER® LTD12 PARTS & PRICING Part prices are subject to change.
  • Page 25 SPEEDSTER® LTD12 PARTS & PRICING...
  • Page 26 SPEEDSTER® LTD12 WIRING DIAGRAM...
  • Page 27 NOTES Mytee Products Inc. 13655 Stowe Dr. Poway, CA 92064 www.mytee.com F X 858.679.7814 © 2017 Mytee Products Inc. Printed in the U.S.A.

This manual is also suitable for:

Speedster ltd5Speedster ltd12

Table of Contents