Measurement - Nikon Aculon Instruction Manual

Measurement

Caution — use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
1. Install a battery in the battery chamber. (See
"Inserting and Changing Battery")
2. Diopter adjustment
Adjust diopter to obtain a clear image in the LCD.
First, rotate the diopter adjustment ring
counterclockwise until it comes to a complete stop.
Next, turn on the power to activate the LCD when
you look through the Nikon Laser Rangefinder.
Rotate the diopter adjustment ring clockwise until
the display comes into focus.
If the diopter is not adjusted to correspond to your
eyesight, you may not be able to correctly aim at
your subject.
3. Measuring
Before measuring, be sure to confirm unit setting.
Measurement
Measurement Measurement
1. Turn on the power (Confirm
the internal display is on).
1. Press the POWER button for power-on.
1. Press the POWER button for power-on. 1. Press the POWER button for power-on.
(Automatic power shut-off after
(Power turns off 8 seconds after the last
(Power turns off 8 seconds after the last
(Power turns off 8 seconds after the last
approx. 8 sec. unattended.)
operation.)
operation.)
operation.)
Immediately
Immediately after power-on.
Immediately after power-on. Immediately after power-on.
after power-on.
(Initializing)
(Initializing) (Initializing)
(Initializing)
3. Press POWER button once to start
3. Press POWER button once to start 3. Press POWER button once to start
continuous measurement for 8 seconds.
continuous measurement for 8 seconds. continuous measurement for 8 seconds.
2. Aim at the target.
Position the target at
2. Aim at the target.
2. Aim at the target. 2. Aim at the target.
the center of the reticle.
Stand-by. Target aiming.
Stand-by. Target focusing.
Stand-by. Stand-by. Target focusing.
Immediately after power-on.
(Initializing)
3. Press POWER button once to start
3. Press POWER button once to start 3. Press POWER button once to start 3. Press POWER button once to start
continuous measurement for 8 seconds.
continuous measurement for 8 seconds. continuous measurement for 8 seconds. continuous measurement for 8 seconds.
3. Press POWER button once to start
(Single measurement mode is not
(Single measurement mode is not (Single measurement mode is not (Single measurement mode is not
3. Press POWER ON/Measurement button once to start measurement.
continuous measurement for 8 seconds.
available with this laser rangefinder.)
available with this laser rangefinder.) available with this laser rangefinder.) available with this laser rangefinder.)
(Single measurement mode is not
Keeping the button depressed enables continous measurement up
available with this laser rangefinder.)
to approx. 20 seconds.
Measuring.
Measuring. Measuring. Measuring.
Measuring.
Measuring.
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
4. During measurement, the internal display shows "distance" and "fail 4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately. 4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
(Laser irradiation mark is blinking.)
(Laser irradiation mark is blinking.) (Laser irradiation mark is blinking.)
(Laser irradiation mark is blinking.)
to measure" indicator alternately. (Laser irradiation mark is blinking.)
4. For 8 seconds, the internal display shows "distance" and "fail to measure" indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
Failure to measure or
Failure to measure or Failure to measure or Failure to measure or
unable to measure
unable to measure distance.
unable to measure distance. unable to measure distance. unable to measure distance.
Failure to measure or distance.
unable to measure distance.
5. After measurement, the measured results are displayed for
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
5. After continuous measurement, the measured results are displayed for 8 seconds, then power 5. After continuous measurement, the measured results are displayed for 8 seconds, then power 5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
approx. 8 seconds, then power turns off. If you press the POWER
turns off. turns off.
turns off.
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
If you press the POWER button during power-on (while the internal display is lit), another
ON/Measurement button during power-on (while the internal
If you press the POWER button during power-on (while the internal display is lit), another If you press the POWER button during power-on (while the internal display is lit), another If you press the POWER button during power-on (while the internal display is lit), another
turns off.
8-second measurement starts.
display is active), another measurement starts.
8-second measurement starts. 8-second measurement starts. 8-second measurement starts.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Target focusing.
Stand-by.
Displays the
Displays the measured Displays the measured
Displays the measured Displays the measured Displays the measured
Displays the measured Displays the measured
measured figure. measured figure.
figure. (Target 1) figure. (Target 2)
figure. (Target 1) figure. (Target 1) figure. (Target 1) figure. (Target 2) figure. (Target 2)
Displays the measured Displays the measured
(Target 1)
figure. (Target 1) figure. (Target 2)
Target focusing.
En
Es
Fr
Pt
Displays the
Displays the measured
figure. (Target 2)
(Target 2)
13