Page 1
User Manual TPC-5212W/TPC-5172T/ TPC-5152T/TPC-B500 Series 電腦 Generation Intel® Core™ i Computer...
Page 2
限用物質含有情況標示聲明書 Declaration of the Presence Condition of the Restricted Substances Marking 型號 (型式) :TPC-5212W ( 系列型號參見說明書 ) 設備名稱:電腦 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴二苯醚 鉛 汞 鎘 多溴聯苯 Unit Hexavalent Polybrominated Lead Mercury Cadmium...
Page 3
限用物質含有情況標示聲明書 Declaration of the Presence Condition of the Restricted Substances Marking 型號 (型式) :TPC-5172T( 系列型號參見說明書 ) 設備名稱:電腦 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴二苯醚 鉛 汞 鎘 多溴聯苯 Unit Hexavalent Polybrominated Lead Mercury Cadmium Polybrominated...
Page 4
限用物質含有情況標示聲明書 Declaration of the Presence Condition of the Restricted Substances Marking 型號 (型式) :TPC-5152T( 系列型號參見說明書 ) 設備名稱:電腦 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴二苯醚 鉛 汞 鎘 多溴聯苯 Unit Hexavalent Polybrominated Lead Mercury Cadmium Polybrominated...
Page 5
The documentation and the software included with this product are copyrighted 2018 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to improve the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
Page 7
Product Warranty (2 years) Advantech warrants the original purchaser that all of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation.
Page 8
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
Page 9
In accordance with the IEC 704-1:1982 specifications, the sound pressure level at the operator position does not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Contents Chapter General Information ......1 Introduction ....................2 Features ....................2 1.2.1 System Kernel................2 1.2.2 O/S Support .................. 2 1.2.3 Certification and Environment............2 LCD and Touch Specifications..............3 Power ......................4 I/O Port Arrangement ................4 Figure 1.1 I/O port arrangement ..........4 Panel Mounting ..................
Page 12
Chapter Easy Installation........ 27 Easy Installation..................28 UI Operation.................... 30 Table 4.1: Status Indicator Table ..........30 Table 4.2: Button Code Definition ..........34 COM1: RS-232 ..................35 COM2: RS-422/485 ................35 RS-422/ 485 Mode Setting via BIOS ............36 TPC-5000 Series User Manual...
Introduction The TPC-5000 touch panel computer is a state-of-the-art modular human-machine interface that features a 12” to 21.5” display and 6 Gen Intel Core i processor that delivers high-performance computing in a compact, fanless system. The key features are as follows: ...
Power Input Voltage: 24 V +/-20% Typical: – TPC-5122T: 24 V @ 3.7 Amp – TPC-5152T: 24 V @ 3.7 Amp – TPC-5172T: 24 V @ 3.7 Amp – TPC-5182W: 24 V @ 3.7 Amp – TPC-5212W: 24 V @ 3.7 Amp I/O Port Arrangement The arrangement of the I/O ports are as shown in Figure 1.1.
Panel Mounting There is an adhesive waterproof gasket on the Mg front bezel. Ensure that the waterproof gasket is in place before installing the TPC system in the panel opening. Install the TPC in the panel opening. Retrieve the clamps and long screws from the accessory pack. Hook the clamps the holes located on the four sides of the bezel.
Transport and Unpacking When accepting a delivery, please check the packaging for visible transport damage and check the delivery for completeness by comparing it with your order form. If you notice any shipping damage or inconsistencies between the contents and your order, please inform the responsible delivery service immediately.
Warning! We recommend turning the system power off before adding or removing a memory card even though the CFast slot supports hot-swapping. Ilestsuggéré de désactiverl'alimentation du système que vousbran- chez ouretirez le carte mémoire, mêmesi la mémoire CompactFlash estrem- plaçable àchaud. Attach the box module to the panel module via the board-to-board connector.
Plug the power lines into the system’s power receptor. Figure 2.5 Power receptor and button pin assignment Connect the power to the system. Calibrate the touchscreen (only applicable for the 12” monitor model). TPC-5000 Series User Manual...
With administrator-level privileges, run the installer for the Advantech watchdog driver. Below is an example of the Advantech watchdog driver setup. To stop the setup pro- cess at any time, click the “Cancel” button on the pop-up screen. The setup program will stop the procedure automatically.
Page 24
Click the “Install” button to continue the installation of the Advantech watchdog driver software. Click the “Restart” or “Close” button on the Advantech Watchdog Driver Setup Wizard pop-up screen to complete the setup. TPC-5000 Series User Manual...
Cabinet Installation and Earth Grounding Setup Follow the steps outlined below to setup the TPC system. Please note that the sys- tem’s grounding pin should be connected to an earth ground. This will provide the system with EMI, ESD, and surge immunity, as well as system isolation. If the TPC system is embedded in a cabinet, the TPC system’s ground, the cabinet’s ground, and an earth ground should be connected together.
Step F: Connect the V+ and V- of the power supply to the TPC system. After completing Steps A to F, power should be supplied to the TPC system. Note! Ensure that all wires follow the installation guidelines or damage to the system may occur.
Extension Installation 2.7.1 Remove the Rear Box Remove the 2 screws on the extension door. Slide the rear cover off to remove it. Figure 2.6 M.2 SSD installation Remove the screws on the I/O bracket of the rear box module to install an iDoor module or riser card.
2.7.2 M.2 (2280) SSD Installation Insert the M.2 (2280) SSD and tighten the screws in the screw holes. Figure 2.8 M.2 SSD installation layout 2.7.3 iDoor Installation The iDoor module should be affixed in place using two screws that are already set in the main board.
2.7.4 Riser Card Installation Riser cards should be inserted at the side of the box module through the track. After insertion, tighten the screws to affix the riser card in place. Figure 2.10 Riser card installation 2.7.5 SIM Card Installation via Mini PCIe The SIM card should be inserted into the mini PCIe slot.
2.7.6 NFC/RFID and Wi-Fi Module Installation NFC/RFID and Wi-Fi modules should be installed on the front panel. Open the bracket at the back of the front panel. Insert the Wi-Fi module into the mPCIe slot, connect the antenna, and tighten the affixing screws.
Applying changes to an image applies all changes made to the operat- ing system during a specific period of time. Advantech provides a utility to run EWF. Follow the steps outlined below to enable this function. Access Start Menu->All Programs->Advantech-> AdvWF and then click EWF Utility.
Page 37
Access the EWF tab and click on the “Enable” button. After the system is rebooted automatically, EWF functionality will be enabled. TPC-5000 Series User Manual...
Writes to folders with write-through exceptions will persist when the device is restarted. Advantech provides a utility to run FBWF. Follow the steps outlined below to enable this function. Access Start Menu->All Programs->Advantech->AdvWF and the click on FBWF Utility.
Easy Installation With the easy installation design, a single person can complete the panel mount pro- cess. Simply follow the steps outlined below. To install the TPC system into a cabinet Step 1: Models with a 4:3 screen ratio Use the snap hooks at the top of the TPC unit to hook the system in the cabinet. Release the pillars at the bottom of the TPC unit to install the system in the cab- inet.
Page 41
Step 2: Place the TPC unit across the cabinet wall. Push the upper part of the system towards the wall until the snap hooks flip back. The snap hooks will hold the machine on the wall. To remove the panel from a cabinet For cabinets with a thickness of 2 mm or less, use a Ø≤...
UI Operation This section provides instructions for operating the HMI utility (GL_Utility), which can be downloaded from Advantech's TPC product support portal at http://support.advantech.com. Located at the lower right corner of the front panel are two function buttons – the iKey and the home key.
Page 43
Single press of the home key-> Home – Back to desktop (default setting) Home - Execute home-key app (setup via the settings page) Long press of the home key-> Home - Long press to disable/enable touch function TPC-5000 Series User Manual...
Page 44
Single press of the iKey -> GLToolbar Utility A. Quick start-> – Press “+” to add a shortcut – Long press the iKey to perform a “right click” until an “X” mark appears in upper right corner to “delete” TPC-5000 Series User Manual...
Page 45
B. Setting -> – A password is required for authorization confirmation upon initial login. The default password is “1234” without an input order to activate. – Setting - Home key: Select an executable file to set as the home key app. The default path destination is desktop –...
C. System management-> – System information – Self diagnosis Note!* TPC-5000 series also provides open button code as following definition for customer's configuration to their Apps/SW applications. The codes are defined from general keyboard input. Table 4.2: Button Code Definition Single Press Long Press iKey (icon)
COM1: RS-232 Pin Definition COM1 Signal COM2: RS-422/485 The COM2 serial ports on the TPC series systems can be adjusted via the BIOS menu and set to RS-422 or RS-485 mode. This port is designed with automatic data flow control capabilities. In other words, the TPC series systems can automatically detect the data flow direction at this port when two-wire RS-485 communication is activated.
RS-422/ 485 Mode Setting via BIOS Restart the system and press the “Delete” key to enter the BIOS setup utility. Access the “Advanced” tab and select “IT8768E Super IO Configuration”. TPC-5000 Series User Manual...
Page 49
Select the “Serial Port 2 Configuration (COM2)” option to configure the RS-422/ 485 mode. Select the “RS-422/485 mode” option. TPC-5000 Series User Manual...