Assigning A Name; When One Page Contains Two Or More Settings; Inputting Numbers And Numerals; Selecting A Part - Roland JUNO-D Owner's Manual

Assigning a name

As an exception, in pages where you can assign a name to a patch or
performance, pressing PAGE/CURSOR [
take you to the next page. The cursor will move to each character in
the name, and when the cursor is located at the last character,
pressing PAGE/CURSOR [ ] again will take you to the next page.
The same applies when moving in the opposite direction.
In pages where you can assign a name, you can hold down [SHIFT]
and use PAGE/CURSOR [ ]/[
page.
fig.r02-07.e
Press [ ].
Press [ ].
Press [ ].
By pressing VALUE [-]/[+], you can change the character at the
cursor position.
Value: space, A–Z, a–z, 0–9, ! " # $ % & ' ( ) * + , - . / : ; < = >
? @ [ ¥ ] ^ _ ` { | }
When inputting characters, you can perform the following
operations conveniently by pressing [0]–[9].
[0]: Deletes all the characters.
[1]: Displays a "." at the cursor position.
[2]: Displays a space at the cursor position.
[3]: Displays an "A" at the cursor position.
[4]: Displays an "a" at the cursor position.
[5]: Displays a "0" at the cursor position.
[6]: Converts capital and lowercase characters.
[7]: Inserts a space at the cursor position.
[8]: Deletes a character at the cursor position and moves the
following characters to the left.
[9]: (no assignment)
] will not immediately
] to jump to the previous or next
Use VALUE [-] / [+] to
modify the characters.
The cursor moves to
the next digit.
Use VALUE [-] / [+] to
modify the characters.
The cursor moves to
the last digit.
Use VALUE [-] / [+] to
modify the characters.
Moves to the next page.
Basic operation of the JUNO-D
When one page contains two or
more settings
In cases such as the page shown below, use PAGE/CURSOR [
[ ] to switch between (A), (B) and (C), and use VALUE [-]/[+] to
modify the value of each parameter.
Example: Master effect switch
fig.r02-08
(A) (B)
Inputting numbers and
numerals
On the JUNO-D, you can select a patch/performance number or
input a numerical value by using VALUE [-]/[+], or by using
[NUMERIC] [0]–[9] to input the value directly.
1. Press [NUMERIC] so it is lit.
The indication will blink.
2. Use the [0]–[9] buttons to input the number.
• Pressing [0] while holding down [SHIFT] switches the +/-
status.
3. If you want to finalize the value, press [ENTER].
The value will be finalized, and [NUMERIC] will go out.
If you decide to cancel, press [EXIT].

Selecting a part

On the JUNO-D you can use [0]–[9] to select parts.
There are a total of sixteen parts. Select parts as follows.
1. Press [PERFORM] so it is lit and you are in Performance
mode.
2. Press [PART SELECT] so it is lit.
3. Press the button as described below.
Part 1 [1] Part 11
Part 2 [2] Part 12
Part 3 [3] Part 13
Part 4 [4] Part 14
Part 5 [5] Part 15
Part 6 [6] Part 16
Part 7 [7]
Part 8 [8]
Part 9 [9]
Part 10 [0]
(C)
[SHIFT] and [1]
[SHIFT] and [2]
[SHIFT] and [3]
[SHIFT] and [4]
[SHIFT] and [5]
[SHIFT] and [6]
43
]/