Roland JUNO-D Owner's Manual page 73

13: SPACE-D
Space-D is a multiple chorus that applies two-phase modulation in
stereo. It gives no impression of modulation, but produces a
transparent chorus effect.
fig.MFX-13
Balance D
L in
Space-D
Space-D
R in
Balance D
Parameter Value
Pre Delay 0.0–100 [ms]
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127
Phase 0–180 [deg]
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Balance # D100:0W–
D0:100W
Level 0–127
14: St CHORUS (Stereo Chorus)
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
fig.MFX-14
Balance D
L in
Chorus
Chorus
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
Cutoff Freq 200–8000 [Hz]
Pre Delay 0.0–100 [ms]
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Adjusts the time delay from
when the direct sound begins
until the processed sound is
heard.
Adjusts the depth of modula-
tion.
Adjusts the spatial spread of the
sound.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Adjusts the output level.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Selects the type of filter.
OFF: A filter will not be used.
LPF: Cuts the frequency range
above the cutoff frequency.
HPF: Cuts the frequency range
below the cutoff frequency.
Adjusts the basic frequency of
the filter.
Adjusts the time delay from
when the direct sound begins
until the processed sound is
heard.
Parameter Value
Depth 0–127
Phase 0–180 [deg]
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Balance # D100:0W–
D0:100W
Level 0–127
15: St FLANGER (Stereo Flanger)
This is a stereo flanger. It produces a metallic resonance that rises
and falls like a jet airplane taking off or landing. A filter is provided
so that you can adjust the timbre of the flanged sound.
fig.MFX-15
Balance D
L in
Flanger
Feedback
Feedback
Flanger
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
Cutoff Freq 200–8000 [Hz]
Pre Delay 0.0–100 [ms]
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127
Phase 0–180 [deg]
Feedback # -98– +98 [%]
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Adding effects
Description
Adjusts the depth of modula-
tion.
Adjusts the spatial spread of the
sound.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Adjusts the output level.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Selects the type of filter.
OFF: A filter will not be used.
LPF: Cuts the frequency range
above the cutoff frequency.
HPF: Cuts the frequency range
below the cutoff frequency.
Adjusts the basic frequency of
the filter.
Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Adjusts the depth of modula-
tion.
Adjusts the spatial spread of the
sound.
Adjusts the amount (%) of the
processed sound that is returned
(fed back) into the input. Posi-
tive (+) settings will return the
sound in phase, and negative (-)
settings will return the sound in
reverse phase.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
73