Roland JUNO-D Owner's Manual page 81

33: ENH>CHORUS (Enhancer
This effect connects an enhancer and a chorus in series.
fig.MFX-33
L in
Enhancer
Mix
R in Enhancer
Mix
Parameter Value
Enhancer Sens # 0–127
Enhancer Mix 0–127
Cho Delay 0.0–100 [ms]
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
Cho Depth 0–127
Cho Balance # D100:0W–
D0:100W
Level 0–127
34: ENH>FLANGER (Enhancer
This effect connects an enhancer and a flanger in series.
fig.MFX-34
L in
Enhancer
Mix
R in Enhancer
Mix
Parameter Value
Enhancer Sens # 0–127
Enhancer Mix 0–127
Flg Delay 0.0–100 [ms]
Flg Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
Flg Depth 0–127
→
Chorus)
L out
Balance D
Balance W
Chorus
Balance W
R out
Balance D
Description
Adjusts the sensitivity of the en-
hancer.
Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
the chorus effect.
Adjusts the modulation depth of
the chorus effect.
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the chorus and
the enhancer sound that is not
sent through the chorus.
With a setting of "D100:0W,"
only the enhancer sound will be
output. With a setting of
"D0:100W," only the enhancer
sound that is sent through the
chorus will be output.
Adjusts the output level.
→
Flanger)
Balance D
L out
Feedback
Balance W
Flanger
Balance W
R out
Balance D
Description
Adjusts the sensitivity of the en-
hancer.
Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
the flanger effect.
Adjusts the modulation depth of
the flanger effect.
Parameter Value
Flg Feedback -98– +98 [%]
Flg Balance # D100:0W–
D0:100W
Level 0–127
35: ENH>DELAY (Enhancer
This effect connects an enhancer and a delay in series.
fig.MFX-35
L in
Enhancer
Mix
R in Enhancer
Mix
Parameter Value
Enhancer Sens # 0–127
Enhancer Mix 0–127
Delay Time 0–500 [ms]
Dly Feedback 98– +98 [%]
Dly HF Damp 200–8000 [Hz],
BYPASS
Dly Balance # D100:0W–
D0:100W
Level 0–12
Adding effects
Description
Adjusts the proportion (%) of
the flanger sound that is fed
back into the effect.
Negative (-) settings will invert
the phase.
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the flanger and
the enhancer sound that is not
sent through the flanger.
With a setting of "D100:0W,"
only the enhancer sound will be
output. With a setting of
"D0:100W," only the enhancer
sound that is sent through the
flanger will be output.
Adjusts the output level.
→
Delay)
L out
Balance D
Balance W
Delay
Balance W
Feedback
R out
Balance D
Description
Adjusts the sensitivity of the en-
hancer.
Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the delay input.
Negative (-) settings will invert
the phase.
Adjusts the frequency above
which delayed sound fed back
to the delay input will be cut.
If you do not want to cut the
high frequencies of the delay
feedback, set this parameter to
BYPASS.
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the delay and the
enhancer sound that is not sent
through the delay.
With a setting of "D100:0W,"
only the enhancer sound will be
output. With a setting of
"D0:100W," only the enhancer
sound that is sent through the
delay will be output.
Adjusts the output level.
81