Related Manuals for Freewing BAe HAWK T.1A
Summary of Contents for Freewing BAe HAWK T.1A
- Page 1 BAe HAWK T.'1 USER MANUAL WINGSPAN: 'I D20MM(40. '16 ") LENGTH: '122'1 MM (4B.'I ") EMPTY WEIGHT: '1450G cw O BATTERY) FCCE®�!O •• www.sz-freew1ng.co"1 MADE IN CHINA...
- Page 2 Celebrating the Red Arrows Demonstration Team's approach to 40 years with their BAE Hawks, the Freewing Hawk T1 is finished in one of the iconic Red Arrows liveries. It is our hope that as you enjoy this model aircraft, you will spread the love of flight and of this historic aircraft's contributions to aviation history.
- Page 3 Product basic information Standard version Wing loading:97.5g/dm Motor: 3048-2300KV brush less outrunner motor Ducted fan: 70mm 12-blade fan ESC : BOA brushless Servo: 9g digital metal gear servo(Bpcs) Flight speed : 160KPH/1 00MPH Empty Weight: 1450g(without battery) Thrust: 2300g Other features Material : EPO Ailerons: Yes Split Flaps: Yes...
- Page 4 PNP Assembly Instructions Traction steel wire Our tests show that excessively long servo extension lines increase the rise of poor connections that can lead to servo brown outs or failure, causing accidents during flight. Instead, this kit contains a steel wire that can be used to pull the main wing/elevator and rudder servo wires through the airplane to the battery compartment, eliminating the need for extension wires.
- Page 5 PNP Assembly Instructions Main Wing Installation Step@ B- Main wing servo cable C- Screws (PA2.6x10x4pcs) As shown in the photo: 1.lnsert the aileron servo cable into the battery compartment and place the main wing on the fuselage. StepO 2.Use 4 screws to attac h. Do not over tighten! Scale Accessories Installation Pitot tube -�...
- Page 6 Insert each servo cable into its corresponding slot on the control board. Test and verify correct function of all control surfaces. After connecting all the servo cables, attach the control board in the location as shown above. BAe HAWK T.1A Item No.:FJ214...
- Page 7 PNP Assembly Instructions Battery Size Battery hatch Use rubberized non-slip tape or Velcro Battery compartment size: L=117 W=63 H=47(mm) Before connecting the battery to the ESC, switch We recommend the following Li Po battery: on the transmitter power and make sure the •...
- Page 8 PNP Assembly Instructions Servo Direction 2000 IJS 2000 IJS The servo positive or reverse rotation is defined as follows: When servo input signal change from 1 000µs to 2000µs, The servo arm is rotated clockwise, positive servo. The servo arm is rotated counterclockwise, reverse servo.
- Page 9 PNP Assembly Instructions Directional Control Test After the build is complete, power up the radio, ensure the throttle is in the lowest position, engage the kill switch if one is assigned and connect a fully charged battery to the ESC. Use the radio to ensure correct control direction. Aileron •...
- Page 10 PNP Assembly Instructions •· di htitti According to our test results, the following rates proved to be a good starting point. Low rates are good for initial flights or less experienced pilots. High Rates will be more sensitive to control inputs. Program your preferred Exponential % and the following rates.
- Page 11 Dongguan Freewing Electronic Technology Ltd HK Freewing Model International Limited Add.:FeiYi Building.face to Labor Bureau, Fu min Middle Road, Dalang Town, Dongguan City , Guangdong Province, China Web: http://www.sz-freewing.com Email:freewing@sz-freewing.com Tel: 86-769-82669669 Fax:86-769-82033233 *�"$"tJt�-=ff4!1��&0§J JI*�� � � "t 00 �ffi � �& 0 §J...