Subscribe to Our Youtube Channel
Related Manuals for Freewing 80mm A-10
Summary of Contents for Freewing 80mm A-10
- Page 1 1/10 Scale Twin 80mm EDF JET User Manual Length:1551mm(61.1") Wingspan:1700mm(66.9") Weight:4250g (w/o Battery) 1~15 中 16~30 www.sz-freewing.com...
- Page 2 Before beginning assembly, please read through the instructions and carefully follow them throughout the build. Freewing and it's vendors will not be held responsible for any losses due to improper assembly and operation. Model airplane operators must be at least 14 years of age.
- Page 3 Basic product information Standard version Wing loading: 124g/dm Motor: 3530-1900KV brushless outrunner motor Ducted fan: 80mm 9-blade fan ESC: 100A brushless UBEC 8A(2pcs) Servo: 17g Digital MG servo (9pcs) 30g Digital MG servo (2pcs) 9g Digital MG servo (1pcs) Weight: 4250g(without battery) Thrust: 6600kg Other features Material: EPO...
- Page 4 PNP Assembly instructions Steel wire use instructions Our tests show that excessively long servo extension lines increase the rise of poor connections that can lead to servo brown outs or failure, causing accidents during flight. Instead, this kit contains a steel wire that can be used to pull the main wing/elevator and rudder servo wires through the airplane to the battery compartment, eliminating the need for extension wires.
- Page 5 PNP Assembly instructions Engine compartment assembly 1.Use the metal wire to pull the ESC cable and throttle cable to the battery compartment. ESC/Battery wire Back of fuselage Batter y compartment Throttle wire 2.Assemble the engine compartment to the rear of fuselage. Screw PA3x12 6pcs)
- Page 6 PNP Assembly instructions Missile Installation Follow the pictures below to install the weapons pylons 2 pylons 1 pylons 3 pylons 4 AIM-9 Missiles AIM-9 pylons Step Step AGM-65 Missiles LAU-131 AGM-65 Missiles Mk-84 AN/ALQ-131 Mk-84 Step Step A-10 Thunderbolt II Item No.:FJ311...
- Page 7 PNP Assembly instructions Antennalnstallation Step Step Step Radar and Wing Fence Installation Screw (PM3x6 1pcs) Stabilizer wing Radar Screws Wing fence (PA3x8 2pcs) Pushrod instructions Flap pushrod size(Inside) Flap pushrod mounting hole(Inside) Pushrod diameter Ø1. 5mm 63mm (2-1/2") Flap pushrod size(Outside) Flap pushrod mounting hole(Outside) Pushrod diameter Ø1 .
- Page 8 PNP Assembly instructions Control board connection diagram A-10 Thunderbolt II uses ribbon wires for convenience. Please refer to the following photo for connecting the electronic equipment. Main wing control board(Left) Main wing control board(Right) Servo lnput Wing tip lights A I L LIGHT Landing gear GEAR...
- Page 9 PNP Assembly instructions Battery size Canopy/battery hatch door Battery B Place the first battery into the BatteryA forward position and secure it with the velcro strap. Velcro A Battery tray Screws (PA3x8 8pcs) Batter y compartment size: Velcro B L=360 W=90 H=90(mm) Before connect the battery and receiver, turn on We recommend the following battery capacity and your transmitter, select the desired model channel...
- Page 10 PNP Assembly instructions Control direction test After the airplane is assembled, but before the first flight, ensure that your control surface directions are correct. Turn on the transmitter and set the throttle in it's the lowest position, then test the control surfaces individually to ensure correct movement.
- Page 11 PNP Assembly instructions Dual rates From our flight test results, we recommend the following parameters for aileron/elevator rates. In low rates, the airplane will be more stable. In high rates, it will be more sensitive. We advise using the recommended high rates in your first flight, then trying the recommended low rates. Afterwards can may want to adjust the rates to suit your individual taste.
- Page 12 Accessories Description Servo Introduction A servo or reversed servo is defined as follows: When the servo input signal changes from 1000ųs to 2000ųs, if the servo arm rotates clockwise, it's a positive servo. If it rotates counter clockwise, it's a reversed servo. If you choose not to use the factory servo, please refer to the following list to ensure the selected servo is the correct size.
- Page 13 1. We have optional power systems available for the A-10.You may want to use one of these, just follow the above steps, the dimensions are suitable for all Freewing 90mm EDF power system and 130A ESC. 2. ESC cable specification:...
- Page 14 Accessories Description Aileron and Flap pushrod Installation Servo Main wing pushrod 1.Use a servo tester or a Aileron horn transmitter to center the servo. Main wing servo trough 2.Use glue to install the servo and aileron horn to the main wing. 3.Feed the servo cable through the trough, when completed for all the servos, apply the decal...
- Page 15 Accessories Description Nose landing gear assembly Please assemble、 disassemble the rear landing gear according to the following photo. Nose gear axle A E - Screw (PA2x8 1pcs) (Ø3.5X9.2mm) Nose wheel C-Buckle A F - (Ø1.5mm) LED lights (Ø 70x20 Grub Screw Spring (M4x3) LED light fixed arm...
- Page 16 Accessories Description Main landing gear Assembly When assembling or disassembling the main landing gear, refer to the following diagram Grub Screw (M4x3) Main gear axle Main gear main rod Main wheel (Ø85x26mm) Grub Screw Grub Screw (M4x3) (M4x3) Electronic retract L-Slant strut Main landing gear (Ø3.5X9.2mm)
- Page 17 Dongguan Freewing Electronic Technology Ltd HK Freewing Model International Limited Add.:FeiYi Building,face to Labor Bureau, Fumin Middle Road, Dalang Town, Dongguan City，Guangdong Province, China Web: http://www.sz-freewing.com Email:freewing@sz-freewing.com Tel: 86-769-82669669 Fax:86-769-82033233 东 莞市飞翼 电子科技有限 公司 香 港 飞 翼 模 型 国 际 有 限 公 司...
Need help?
Do you have a question about the 80mm A-10 and is the answer not in the manual?
Questions and answers