Modifying The Default Ip Service; Conference Control Using Dtmf Codes - Polycom RMX 2000 Installation & Quick Start Manual

RMX

Modifying the Default IP Service

This section describes the definition of H.323 Network Service. For detailed description
of H.323, SIP and ISDN Network Service definitions, see the RMX Getting Started Guide,
"First Time Installation and Configuration".
On the RMX 2000, IPv4 is the default protocol for setting the Network Service in the
Fast Configuration Wizard.
In the Fast Configuration Wizard, select Next to move from one window to another.
1
2
3
2
®
2000
Change the default service
name if required.
Enter the address to be
4
used by IP endpoints when
dialing in to the MCU.
Enter the IP address(es) of
the media card(s).
Enter the subnet mask of
the MCU.
5
Enter the IP address of the
6 In the IP Network Service creation confirmation, click OK.
default router.
Enter the name of the MCU
on the network.
Optional. Select Specify to 7
define a DNS server.
8
Click Save & Close.
Optional. Define the DNS
9
In the Success Message box confirming successful configuration, click OK.
server properties:
10 In the Reset Confirmation dialog box, click Yes.
• Registration mode
11 In the Please wait for system reset message box, click OK.
• The name of the MCU
System restart may take up to five minutes.
domain
12 Refresh the browser periodically until the Login screen is displayed and Login.
• The static IP address of
In the Main Screen an MCU State indicator displays the time remaining until the
the primary DNS server
system start-up is complete.
MCU Status remains in Major and the red ERR LED on the RMX front panel remains ON
until the default RMX User is replaced with a new User and the RMX Time is set:
13 Create a new User with Administrator permissions. For more information see the
Select H.323 as the IP RMX 1500/2000/4000 Administrator's Guide, "Adding a New User" on page 14-4.
Network Type.
14 Set the RMX time (Setup > RMX Time) and click OK. For more information, see
the RMX 1500/2000/4000 Administrator's Guide, "RMX Time" on page 19-41.
15 Logout and Login using the new User name and password and then delete the
default User (POLYCOM).
When the above steps are completed and if there are no System Errors, the green RDY
LED on the RMX's front panel turns ON and the red ERR LED turns OFF.
Connecting to a Conference Directly or via Entry Queue
The RMX is shipped with pre-configured default conferencing entities that can be used
to dial in and start conferences. Default (Transit) Entry Queue ID: 1000, default Meeting
Room IDs: 1001, 1002, 1003, and 1004.
Select Specify to configure
the gatekeeper parameters.
H.323 Participants
Enter gatekeeper's host
Dial: [MCU Prefix in Gatekeeper][Conference or Entry Queue ID/Name]
name or IP address.
For example, if the MCU prefix in gatekeeper is 925, enter 925 or 9251000 to connect to
Enter the string with which the
the EQ or 9251001/2/3/4 to connect directly to the conference. When connected to the
MCU registers itself with the
EQ, enter the destination Meeting Room ID (i.e. 1001, 1002, 1003 or 1004).
gatekeeper.
Alternatively, use the EQ or conference name. For example, if the conference name is
Enter the alias that identifies
the RMX's Signaling Host Maple_Room, the participant can dial: 925Maple_Room.
within the network. Up to five
SIP Participants
aliases can be defined for
each RMX.
Dial: conference_routing _name@domain_name. Conference routing name must be
registered with the SIP server. For example, enter 1001@polycom.com if conference
routing name is 1001 and the domain name is polycom.com.
Optional. Modify the default
ISDN and PSTN Participants
settings of the system flags
Dial one of the numbers assigned to the conference, Meeting Room or Entry Queue with
that define the general
the required country and area code. When connected to an EQ you are routed to the
system behavior such as the
conference according to the destination conference ID you enter.
number of digits in the
For example, if the conference assigned dial in number is 4045555, dial this number with
conference ID assigned by
the appropriate area code (for example, 678) and country code (001).
the MCU.
These flags can be modified
later, if required, by selecting

Conference Control Using DTMF Codes

the System Configuration
option from the Setup menu.
Operation
Play Help Menu
Mute My Line
Unmute My Line
Increase Broadcast Volume
Decrease Broadcast Volume
Invite Participant
Start Click&View to modify
personal layout
DTMF String Operation DTMF String
*0
*83 Request private assistance
*6 Request assistance for 00
conference
#6
*9 Increase Listening Volume *76
#9 Decrease Listening Volume #76
*72 Change To Chairperson *78
** Show Number of *88
Participants
DOC2665A