Conair TrueBlend TB45-4 User Manual page 28

T e c h n i c a l S p e c i f i c a t i o n s
TPBS027-0207
Side view
C
1
NOTE: Side and front view
drawings are model TB500-4.
The bin positions change for a
TB500-6, see the top view.
MODELS
Performance characteristics
Batch size lb {g}
Maximum throughput rate lb/hr {kg/hr}*
Bin capacity - main ingredient ft
Bin capacity - minor ingredient ft
Maximum number of materials
Number of vertical discharge valves
Number/(size) of major bin valves
Number/(size) of minor bin valves
Dimensions inches {mm}
A - Height above mounting plate †
B - Width
C - Depth
D - Control height
E - Control width
F - Control depth
Weight lbs {kg}
Installed
Shipping
Voltage total amps
115V/1 phase/60 hz
230V/1 phase/50 hz
Compressed air requirements
Discharge valves
Maximum loader sizes
15 inch loaders - number of loaders -
8 inch loaders - number of loaders -
26
Front view
B
4
A
Drain chute
Purchase the
material drain chute
that readily installs to
the chassis opening of
the blender for fast
and simple cleanout.
TB500-4
11 {5000}
1550 {703}
3 {liter} 2.7 {76.4}
3 {liter} 2.7 {76.4}
4
4
2 - (100/60 mm) 2 - (100/60 mm)
2 - (30 mm) 4 - (30 mm)
63.00 {1600} 63.00 {1600}
40.13 {1026} 40.13 {1026}
43.00 {1092} 43.00 {1092}
8.25 {209.6} 8.25 {209.6}
9.25 {235.0} 9.25 {235.0}
4.75 {120.6} 4.75 {120.6}
400 {182}
520 {236}
6.3
3.2
90 psi @ 0.2 ft 3 /min {6 bars @ 0.09
liters/sec}; 1/4 in. NPT fitting
4
NA
4 position
Position 1
3
‡Position 4
optional
TB500-6 MOUNTING INTERFACE
Dimensions
11 {5000}
shown in
inches and {mm}.
1200 {544}
2.7 {76.4}
1.35 {38.2}
6
6
Mounting bolt hole size (8 holes) 9/16 inch {14.0 mm}.
Predrilled 8 x 8 and 12 X 12 mounting pattern as standard.
400 {182}
520 {236}
SPECIFICATION NOTES
*
Maximum throughput rates are based on 35 lb/ft
6.3
using all standard valve sizes. Use of reducer inserts will lower the rate
3.2
shown.
†
The optional flow control valve will mount inside the chassis in the space
of the manual slide valve. Conair recommends using the optional flow
control valve when mounting the blender on a stand, surge bin or hopper.
‡ TB500-4 hopper positions three and four are supplied with 12-8
adapters with 8 inch cover plates as standard. TB500-6 hopper
2
position two is supplied with a 12-8 adapter and an 8 inch cover
4
plate as standard.
Specifications may change without notice, consult with a Conair represen-
tative for the most current information.
T r u e B l e n d ™ T B 5 0 0 - 4
a n d T B 5 0 0 - 6
Top view
Position 2 Position 1
‡Position 5
‡Position 3
Control
E
F
Mixing chamber access door - this
side of the interface.
16-5/32 {410}
12 {305}
8 {203}
3-5/32
diameter
{80}
2-1/16
8-1/16
{53}
{205}
4-1/16
{103}
Edition: February 2007
6 position
Position 2
‡Position 4
D
3
pelletized material and