GE Interlogix NX-8 Installation And Startup page 29

LOCATION 103 - PARTITION 6 ENTRY EXIT TIMERS
(4 segments, numerical data) Location 103 is used to enter in seconds the Entry and Exit times. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition
1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
LOCATION 104 - ACCOUNT CODE FOR PARTITION 7
(6 segments, numerical data) The account code sent when partition 7 is reported is programmed in location 104. If
location 104 is left unprogrammed (all A10") then the account code corresponding to the Phone number dialed
will be used. If the account code is less than six digits, program a A10" in the segment immediately after the last digit of
the account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 105 - PARTITION 7 FEATURE AND REPORTING SELECTIONS
(3 segments, feature selection data) Location 105 is used to enable certain features that can be accessed or are visible
to the user from the keypad of the system. In addition, certain communicator reports are enabled in this location. Each
of these features can be enabled by partition. This location contains 3 segments, with eight possible features per
segment. Refer to Location 23, Segments 1 - 3 on page 18 for the feature selections. If all segments are blank
(nothing enabled), the features for partition 1 will be used.
LOCATION 106 - PARTITION 7 ENTRY EXIT TIMERS
(4 segments, numerical data) Location 106 is used to enter in seconds the Entry and Exit times. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition
1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
LOCATION 107 - ACCOUNT CODE FOR PARTITION 8
(6 segments, numerical data) The account code sent when partition 8 is reported is programmed in location 107. If
location 107 is left unprogrammed (all A10") then the account code corresponding to the Phone number dialed
will be used. If the account code is less than six digits, program a A10" in the segment immediately after the last digit of
the account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 108 - PARTITION 8 FEATURE AND REPORTING SELECTIONS
(3 segments, feature selection data) Location 108 is used to enable certain features that can be accessed or are visible
to the user from the keypad of the system. In addition, certain communicator reports are enabled in this location. Each
of these features can be enabled by partition. This location contains 3 segments, with eight possible features per
segment. Refer to Location 23, Segments 1 - 3 on page 18 for the feature selections. If all segments are blank
(nothing enabled), the features for partition 1 will be used.
LOCATION 109 - PARTITION 8 ENTRY EXIT TIMERS
(4 segments, numerical data) Location 109 is used to enter in seconds the Entry and Exit times. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition
1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
NX-8 Commercial Fire
Technical Manuals Online! - http://www.tech-man.com
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry Delay.
Exit time that will be used for all zones designated as Delay 2.
29