GE Interlogix NX-8 Installation And Startup page 27

LOCATIONS 88 – 109 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES AND/OR FEATURES FOR EACH
PARTITION. IF A LOCATION IS LEFT UNPROGRAMMED, THE FEATURE FOR PARTITION 1 AND ACCOUNT CODE
FOR THE PHONE NUMBER WILL BE USED.
LOCATION 88 - ACCOUNT CODE FOR PARTITION 1
(6 segments, numerical data) Location 88 contains the account code sent when partition 1 is reported. If location 88
is left unprogrammed (all A10"s), then the account code corresponding to the Phone number dialed will be
used. If the account code is less than six digits, program a A10" in the segment immediately after the last digit of the
account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 89 - ACCOUNT CODE FOR PARTITION 2
(6 segments, numerical data) Location 89 contains the account code sent when partition 2 is reported. If location 89
is left unprogrammed (all A10"s), then the account code corresponding to the Phone number dialed will be
used. If the account code is less than six digits, program a A10" in the segment immediately after the last digit of the
account code. If the account code is 6 digits long program all 6 segments.
LOCATION 90 - PARTITION 2 FEATURE AND REPORTING SELECTIONS
(3 segments, feature selection data) Location 90 is used to enable certain features that can be accessed or are visible
to the user from the keypad of the system. In addition, certain communicator reports are enabled in this location. Each
of these features can be enabled by partition. This location contains 3 segments, with eight possible features per
segment. Refer to Location 23, Segments 1 - 3 on page 18 for the feature selections. If all segments are blank
(nothing enabled), the features for partition 1 will be used.
LOCATION 91 - PARTITION 2 ENTRY EXIT TIMERS
(4 segments, numerical data) Location 91 is used to enter in seconds the Entry and Exit times. There are 2 separate
entry and exit times.
partition 1 will be used.
Segment 1, Entry time 1:
Segment 2, Exit time 1:
Segment 3, Entry time 2:
Segment 4, Exit time 2:
LOCATION 92 - ACCOUNT CODE FOR PARTITION 3
(6 segments, numerical data) The account code sent when partition 3 is reported is programmed in location 92. If
location 92 is left unprogrammed (all A10" ) then the account code corresponding to the Phone number dialed
will be used. If the account code is less than six digits, program a A10" in the segment immediately after the last digit
of the account code. If the account code is 6 digits long program all 6 segments.
LOCATION 93 - PARTITION 3 FEATURE AND REPORTING SELECTIONS
(3 segments, feature selection data) Location 93 is used to enable certain features that can be accessed or are visible
to the user from the keypad of the system. In addition, certain communicator reports are enabled in this location. Each
of these features can be enabled by partition. This location contains 3 segments, with eight possible features per
segment. Refer to Location 23, Segments 1 - 3 on page 18 for the feature selections. If all segments are blank
(nothing enabled), the features for partition 1 will be used.
LOCATION 94 - PARTITION 3 ENTRY EXIT TIMERS
(4 segments, numerical data) Location 94 is used to enter in seconds the Entry and Exit times. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition
1 will be used.
Segment 1, Entry time 1:
Segment 2, Exit time 1:
Segment 3, Entry time 2:
Segment 4, Exit time 2:
NX-8 Commercial Fire
Technical Manuals Online! - http://www.tech-man.com
Valid entries are 10-255 seconds. If all segments are A0", the entry and exit times for
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
27