Display - FUTABA FMT-03 Instruction Manual

DISPLAY

The following LCD screen adjustments and auto
power off setting are possible:
● Select [DISPLAY] at the system menu and call the setup
screen shown below by pushing the RTN button.
● Select the function name
and return to the System
menu by pushing the RTN
button or pushing the
Home/Exit button.
LCD contrast adjustment
1. Scrolling the edit dial to select "LCD CONTRAST"
and push the RTN button to switch to the data
input mode and adjust the contrast by turning the
edit dial to the left and right.
Setting range: (Lighter) 0 to 30 (Darker)
Initial value: 15
Push the RTN button to end adjustment and return
to the cursor move mode.
*Adjust to the contrast while watching the screen display.
*When you want to reset the contrast to the initial state, select
"LCD CONTRAST" and push the RTN button for 1 second.
Backlight brightness adjustment
1. Scrolling the edit dial to select "BACKLIGHT
BRIGHTNESS" and push the RTN button to switch to
the data input mode and adjust the contrast by
turning the edit dial to the left and right.
Setting range: (Darker) 0 to 30 (Lighter)
Initial value: 10
Push the RTN button to end adjustment and return
to the cursor move mode.
*Adjust to the brightness while watching the screen display.
*When you want to reset the contrast to the initial state, select
"BACKLIGHT BRIGHTNESS" and push the RTN button
for 1 second.
Back-light off-timer
1. Select "Back-light timer" and push the RTN button
to switch to the data input mode and adjust the
back-light off-timer by scrolling the edit dial.
"OFF TIMER": Adjust the time when the back-light
turns off after operating the edit dial.
Setting range: 10 to 240 sec (each 10 sec), OFF
(always on)
Initial value: 10 sec
*When you want to reset the value to the initial state, push
the RTN button for one second.
2. Push the RTN button to end adjustment and
return to the cursor mode.
*If the back light is on for a long time, consumption current
will increase.
38 <Functions of System Menu>
LCD contrast adjustment and automatic key lock
● Backlighting brightness adjustment
● Backlighting off timer adjustment
● Key lock setup
A PIN can also be set to protect the set data.
Start lock
Auto Lock functions automatically when the
model changes or power is turned on.
*To temporarily allow access to the FMT-03 programming
push and hold the S1 button for one second. Please note,
the Auto Lock function timer will resume immediately once
again.
1. Select "STARTUP LOCK" and push the RTN button to
switch to the data input mode and adjust the ON
or OFF by scrolling the edit dial.
Setting range: ON or OFF
Initial value: OFF
Set PIN ID
A PIN can also be set to protect the set data.
*Please do not forget the ID you set here. You have to input
the ID in order to unlock the ID lock on the home screen.
If you do not need the ID lock feature, please set the ID for
"00000000".
1. Select "ID" and push the RTN button to switch to the
ID input screen.
2. Scrolling the edit dial to select "00000000" and push
the RTN button to switch to the data input mode
and adjust the number by turning the edit dial
to the left and right. Push the RTN button to end
adjustment and return to the cursor move mode.
3. UNLOCK: Push the S1 button for about 1 second
in the edit dial locked state. And input the ID you
have set. The edit dial is enabled again.
Automatic lock
Auto Lock functions automatically when there is
no operation from the HOME screen display for a
chosen number of seconds.
1. Scrolling the edit dial to select "AUTOMATIC LOCK"
and push the RTN button to switch to the data
input mode and adjust the time by turning the edit
dial to the left and right.
Setting range: INH, 0 to 120 (s)
Initial value: INH
<Edit dial>
Scrolling
● Moving cursor
S1
● Selecting mode
● Adjusting value