Related Manuals for Dog trace d–control 200 mini
Summary of Contents for Dog trace d–control 200 mini
- Page 1 User Guide d–control 200 mini Electronic training collar – basic training set for one dog d–control 202 mini Electronic training collar – basic training set for two dogs – with a carrying case...
- Page 2 Declaration of Conformity VNT electronics s.r.o. Smetanovo náměstí 104 570 01, Litomyšl IČO: 64793826 declare under own responsibility that the product: Electronic training collar Dogtrace d-control 200 mini is in compliance with essential requirements and other relevant provisions of Directive 1999/5/EC from 9. 3. 1999 meets requirements of General Licence of The Czech Telecommunication Office according to general licence no.
-
Page 3: Table Of Contents
Hereby, VNT electronics s.r.o. , declares that this d-control 200 mini is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. WARNING: The person with a personal instrument to support heart activity (pacemaker, defibrillator) must respect the relevant precautionary measures. The d–control emits a certain stationary magnetic field (lower part of the remote controller and RF signals). -
Page 4: Introduction
Introduction The electronic training collar Dogtrace d–control, consisting of the transmitter and the receiver, it is a modern, safe, reliable, and effective training tool. With the d-control training collar you can make corrections that are suited to your dog‘s temperament and the distraction level of the moment, at the proper time, for maximum training efficiency. -
Page 5: Product Description
Product description TRANSMITTER RECEIVER LCD DISPLAY TRANSMITTER - 1 - Backlit LCD display, 2 - Booster button, 3 - Stimulation button, 4 - Tone signal button, 5 - ON/OFF Switch, 6 - Adjustment of the level of the stimulation, 7 - Dog selection button (dog A, dog B) RECEIVER - 1 - Strap, 2 - Contact points, 3 - ON/OFF LED Indicator, 4 - indicator area where the ON/OFF magnetic switch is located... -
Page 6: Battery Insertion And Replacement
Battery insertion and replacement INSERTION (REPLACEMENT) OF THE BATTERY IN THE RECEIVER Unscrew the 4 screws of the top of the receiver using a cross-head screwdriver and remove the lid. Insert the lithium CR2 3V battery into the battery compartment. Please check that and the battery is installed with correct polarity (according to the polarity indicated with the "+"... -
Page 7: Choosing The Contact Points
INSERTION (REPLACEMENT) OF THE BATTERY IN THE TRANSMITTER Observe polarity when installing the battery. Reversing the battery will damage the transmitter. Use only lithium batteries. CR2 3V Remove the transmitter battery cover using a cross-head screwdriver. If replacing the battery, remove the old battery and dispose of it ... -
Page 8: Switching On/Off
Switching ON/OFF SWITCHING THE TRASNMITTER ON/OFF Switching on: Press down for 1 second the button on the transmitter. The LCD display indicates that the unit is active. Switching off: Again, press down for 1 second the button on the transmitter. ... -
Page 9: Programming (Coding) The Transmitter With The Receiver
Programming (coding) the transmitter with the receiver Each transmitter has its own operational code. The programming of the transmitter with the receiver enables the two units to work together. This operation will help you to program the receiver to work with a new transmitter or to program a new receiver to work with your existing transmitter. -
Page 10: Transmitter - Button Functions
Transmitter - button functions The d–control 200 transmitter is designed to operate with two separate receivers (dog A and dog B). The selected level of stimulations can be different for each receiver. Button - Tone signal The receiver emits a beeping noise when a "Tone button" is pressed. If the button is not released after 10 seconds, the tone will automatically turn off. - Page 11 Programming the "Booster button": press the selection button for approximately 5 seconds until the level of stimulation flashes on the LCD display. press the button to increase or decrease the level of stimulations (0-5). press the selection button to confirm the level selected.
-
Page 12: How To Check That Your D-Control Works Correctly
How to check that your d–control works correctly You can check anytime that your d-control is operating correctly. Before doing so, make sure that the receiver is switched off. Place the test discharge lamp in contact with each of the ... -
Page 13: Getting The Best Results
Getting the best results The training commands are transmitted to the receiver by radio waves. The range of the d-control 200 mini is approximately 200 metres depending on the geographic conditions. The transmitter range may vary depending on the way you use your transmitter, hold the transmitter away from your body and avoid touching the front part of the transmitter where the antenna is located. -
Page 14: Training Tips
Training tips The trainer’s elementary knowledge in dog training is the prerequisite for using the training collar. Do not hesitate to contact a professional trainer for any further advice. You can start using the collar with dogs of 6 months of age who has undergone the basic training ... -
Page 15: Caution
Caution Keep away from children. Do not leave the device in or around a high temperature heat source. Check the receiver for proper tightness of screws and seal before each use. Battery of the receiver needs to be replaced in every two years, check the battery power level ... -
Page 16: Troubleshooting
conditions, water can cause irreversible damage to your transmitter. The receiver is waterproof. The receiver case is provided with a seal that forms a waterproof barrier between the lid and main housing of the case. If the seal is loose, out of alignment or twisted, it will compromise the waterproof integrity of the case. -
Page 17: Technical Specifications
Technical specifications TRANSMITTER Weight ..........64 grams (without battery) Range . -
Page 18: Warranty Terms And Conditions
Warranty Terms and Conditions VNT electronics Ltd. provides a 2-year warranty on the DOGtrace product with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: batteries ... - Page 19 5. We require that all items being sent for repair must be clean. Items deemed insufficiently clean will be returned to the customer unrepaired. Please do not include the strap or any other accessories if not subject to warranty. 6. Other rights and liabilities of the manufacturer and claimants are based on relevant general obligatory legal regulations of the country where the product was sold.
-
Page 20: Certificate Of Warranty
Manufacturer: VNT electronics s.r.o. Smetanovo náměstí 104 570 01 Litomyšl Czech Republic Phone: +420 733 121 890 www.dogtrace.com Dealer: Version 2016-4-21 / EN Copying of this user guide is strictly prohibited without the prior written consent of VNT electronics Ltd.