Related Manuals for Dog trace d-control professional 1000 mini
Summary of Contents for Dog trace d-control professional 1000 mini
- Page 1 d-control professional 1000 • mini professional 2000 • mini Elektronisches Erziehungshalsband Electronic training collar Collare elettronico di addestramento Collier électronique de dressage Elektronische trainingshalsband...
- Page 2 DECLARATION OF CONFORMITY Manufacturer: VNT electronics s.r.o. Dvorská 605 563 01 Lanškroun IČO: 64793826 declare under own responsibility that the product: Electronic training collar Dogtrace d-control professional 1000 / mini Dogtrace d-control professional 2000 / mini is in compliance with the essential requirements and other relevant provisions of Directivem 2014/53/EC, meets requirements of General Licence of The Czech telecommunication office according to general licence no.
-
Page 3: Table Of Contents
CONTENTS 2 Important notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3 ECMA . -
Page 4: Important Notice
IMPORTANT NOTICE The electronic training collars d-control are intended only to train animals. They are not intended to harm, injure or to cause fear. Do not use the electronic training collars for dogs with health problems (e.g. heart disease, epilepsy, etc.) or for dogs with behavioral disorders (aggressive dogs etc). The collar should never be worn for more than 12 hours a day. -
Page 5: Introduction
INTRODUCTION The electronic training collar Dogtrace d-control professional, consisting of the transmitter and the receiver, is a modern, safe, reliable and effective training tool. d-control training collar enables you to make corrections that are suited to your dog‘s temperament and the distraction level of the moment, at the right time and with maximum training efficiency. -
Page 6: Optional Accessories
4.2 Optional accessories Dummy receiver (with the strap) Spare batteries Spare screws Spare rubber seal for the transmitter and the receiver Spare contact points (12, 17 and 21 mm) Woven and plastic collars – various colours PRODUCT DESCRIPTION 5.1 Transmitter 1. -
Page 7: Receiver
Display 1. Command indicator of function buttons A1 or B1 2. Command indicator of function buttons A2 or B2 3. Transmission indicator 4. Current button setup indication 5. Battery power indicator 6. Indicator of mode or stimulation level 7. Locking of selected function and command 5.2 Receiver 1. -
Page 8: Transmitter Settings
6.3 Transmitter settings 1. Switching ON/OFF – press down for 1 second the button 2. Selection of function button for setting – by pushing this button shortly and repeteadly you switch between buttons A1/A2/B1/B2. Buttons A1/A2 are designed for a dog A and buttons B1/B2 are designed for a dog B. TIP: When using the device for training one dog, you can program function buttons B1/B2 with the same receiver (collar) as function buttons A1/A2 - see chapter 7.4 Pairing (programming) function buttons B1/B2 (or second... -
Page 9: Checking The Receiver Battery Status
Note: When you replace the battery quickly, you may not hear the audible beep tone of the collar. Make sure that the rubber seal is clean and correctly seated in its groove. Clean any dirt from the seal. Put the battery cover of the receiver back and screw in the 4 screws adequately. 7.2 Checking the receiver battery status The status of the battery is indicated by LED indicators on the side of the receiver. -
Page 10: Pairing The Receiver With The Transmitter
7.4 Pairing (programming) the receiver with the transmitter Each transmitter has its own radio operational code. The programming of the transmitter with the receiver enables those two units to work together. When purchasing new d-control professional set, there is no need to program the device. The set is programmed from the manufacture. -
Page 11: Choice Of The Contact Points
4. After 5 seconds the receiver LED indicators will flash 3 times green and red colour simultaneously. Afterwards the green and red LED indicators will start alternately flashing. 5. Press down B1 or B2 button (or any other function button on the second transmitter). -
Page 12: The Basics Of Training Collar Usage
THE BASICS OF TRAINING COLLAR USAGE The trainer’s elementary knowledge of the dog training is the prerequisite for using the training collar. If you don´t have this knowledge, we recommend you to contact a training center, a cynology club, or a school for dogs where you will learn the basic communication with your dog. - Page 13 − Momentary / continuous stimulation: This function enables you to activate a safe stimulation warning impulses in the receiver transmitted by two contact points. The purpose of stimulation impulses is not to hurt the dog, but this impulse is very unpleasant for your dog. Your dog will soon create a connection between your command, an audible beep tone and the unpleasant feeling on the neck.
- Page 14 Lichtfunktion: For an easy localization of your dog in the dark, this function provides several modes of LED light. The LED - diodes are placed in the transparent receiver housing of the collar. The transmitter also allows you to set a different interval of flashing when using two collars at the same time - you can easily spot your dogs according to the flashing interval (example: a dog A - flashes once in a second and a dog B - flashes once in two seconds).
-
Page 15: For The Best Results
FOR THE BEST RESULTS 9.1 Maximum transmitter range The training collar d-control professional 1000 / mini, 2000 / mini can be used up to 1000 m or 2000 m working range. The maximum range depends on many factors - weather, terrain, vegetation and so on. To ensure maximum working range of the device: Do not cover the transmitter antenna When transmitting commands, hold the transmitter in a vertical position, away... -
Page 16: Troubleshooting
TROUBLESHOOTING 1. Read again this user guide and make sure the problem is not caused by a flat battery or incorrect use. 2. Make sure the batteries are inserted with the correct polarity. 3. If the transmitter does not communicate with the receiver, try to program communication - see chapter: 7.4 Pairing (programming) the transmitter with the receiver. -
Page 17: Maintenance
MAINTENANCE It is important to keep the device clean. Never use volatile substances eg.: thinner, gasoline or other cleaners. To clean your Dogtrace d-control use a soft, damp cloth and, if necessary, neutral detergent. The transmitter and the receiver (collar) Dogtrace d-control professional is waterproof only on condition of the good state of the seal. -
Page 18: Warranty Terms And Conditions
WARRANTY TERMS AND CONDITIONS VNT electronics s .r .o . provides a 2 year warranty on the Dogtrace products with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: accumulators straps direct or indirect risks during transportation of the product to the retailer...