Related Manuals for Dog trace d-control 502 mini
Summary of Contents for Dog trace d-control 502 mini
- Page 1 d–control 500, 900, 1500 mini Electronic training collar d–control 502, 902, 1502 mini Electronic training collar set for two dogs User guide...
- Page 2 Declaration of Conformity VNT electronics s.r.o. Smetanovo náměstí 104 570 01, Litomyšl IČO: 64793826 declare under own responsibility that the product: Electronic training collar Dogtrace d-control 500, 900 and 1500 mini is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC from 9.
-
Page 3: Table Of Contents
Hereby, VNT electronics s.r.o., declares that this d-control 500, 900, 1500 mini is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. WARNING: The person with a personal instrument to support heart activity (pacemaker, defibrillator) must respect the relevant precautionary measures. -
Page 4: Introduction
Introduction The electronic training collar Dogtrace d–control, consisting of the transmitter and the receiver, it is a modern, safe, reliable, and effective training tool. With the d-control training collar you can make corrections that are suited to your dog‘s temperament and the distraction level of the moment, at the proper time, for maximum training efficiency. -
Page 5: Product Description
Product description TRANSMITTER RECEIVER LCD DISPLAY TRANSMITTER 1 – Antenna, 2 – Booster button, 3 – Stimulation button, 4 – Tone signal button, 5 – Backlit LCD display, 6 – ON/OFF Switch, 7 – Dog selection button (dog 1, dog 2), 8 –... -
Page 6: Battery Insertion And Replacement
Battery insertion and replacement INSERTION (REPLACEMENT) OF THE BATTERY IN THE RECEIVER Unscrew the 4 screws of the top of the receiver using a cross-head screwdriver and remove the lid. Insert the lithium CR2 3V battery into the battery compartment. Please check that and the battery is installed with correct polarity (according to the polarity indicated with the "+"... -
Page 7: Choosing The Contact Points
INSERTION (REPLACEMENT) OF THE BATTERY IN THE TRANSMITTER Remove the transmitter battery cover using a cross-head screwdriver. If replacing the battery, remove the old battery and dispose of it properly. Place the alkaline AA 1,5V batteries in the holder and press into place. Observe polarity when ... -
Page 8: Switching On/Off
Switching ON/OFF SWITCHING THE TRASNMITTER ON/OFF Switching on: Press down for 1 second the button on the transmitter. The LCD display indicates that the unit is active. Switching off: Again, press down for 1 second the button on the transmitter. ... -
Page 9: Programming (Coding) The Transmitter With The Receiver
Programming (pairing) the transmitter with the receiver Each transmitter has its own operational code. The programming of the transmitter with the receiver enables the two units to work together. This operation will help you to program the receiver to work with a new transmitter or to program a new receiver to work with your existing transmitter. -
Page 10: Transmitter - Button Functions
Transmitter - button functions The Dogtrace d–control transmitters are designed to operate with two separate receivers (dog 1 and dog 2). The selected level of stimulations can be different for each receiver Button - Tone signal The receiver emits a beeping noise when a „Tone button“ is pressed. If the button is not released after 30 seconds, the tone will automatically turn off. - Page 11 Button -Booster Pressing the „Booster button“ enables you to use different levels of pre-set stimulation intensity at the transmitter. The stimulation is transmitted by the two contact points located on the receiver as long as the button is pushed. If the button is not released after 4 seconds, the stimulation will automatically turn off as a safety feature.
-
Page 12: How To Check That Your D-Control Works Correctly
External remote control ONE TOUCH The electronic training collars d-control 510, 910 and 1510 mini are provided with the external remote control ONE TOUCH. It enables you to activate the pre-set stimulation (momentary or continuous) at the receiver by a quick pressing of one button. -
Page 13: Using D-Control Training Collar In Winter
FITTING THE COLLAR The receiver needs to be very snug around the dog‘s neck to work properly. A loose fit can allow the receiver to move around on the dog‘s neck. The collar must be just tight enough to allow the contact points to make good contact on your dog‘s skin. -
Page 14: Training Tips
Training tips The trainer’s elementary knowledge in dog training is the prerequisite for using the training collar. Do not hesitate to contact a professional trainer for any further advice. You can start using the collar with dogs of 6 months of age who has undergone the basic training ... -
Page 15: Maintenance
Do not use the electronic training collar for dogs under 6 months of age. Do not use the electronic training collar for pregnant or nursing bitches. Do not use the electronic training collar for dogs with health problems particularly heart disease, ... -
Page 16: Troubleshooting
Troubleshooting If your device seems to operate improperly, read this manual again, check the receiver battery and replace it if necessary. Try to initialize the receiver by removing the battery from the battery holder in the receiver, then use ... -
Page 17: Technical Specifications
Technical specifications TRANSMITTER Weight ......... . 88 (95 - d-control 1500 mini) grams (without battery) Range . -
Page 18: Warranty Terms And Conditions
Warranty Terms and Conditions VNT electronics Ltd. provides a 2-year warranty on the Dogtrace product with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: batteries ... - Page 19 5. We require that all items being sent for repair must be clean. Items deemed insufficiently clean will be returned to the customer unrepaired. Please do not include the strap or any other accessories if not subject to warranty. 6. Other rights and liabilities of the manufacturer and claimants are based on relevant general obligatory legal regulations of the country where the product was sold.
-
Page 20: Certificate Of Warranty
Manufacturer: VNT electronics s.r.o. Smetanovo náměstí 104 570 01 Litomyšl Czech Republic Phone: +420 733 121 890 www.dogtrace.com Version 2016-5-31 / EN Copying of this user guide is strictly prohibited without the prior written consent of VNT electronics Ltd.