Electronic training collar –
basic training set for one dog.
electronic training collar –
basic training set for two dogs –
with a carrying case (20 pages)
Summary of Contents for Dog trace d-control 500 mini
Page 1
d–control 500, 900, 1500 mini Electronic training collar User guide...
Page 2
Declaration of Conformity VNT electronics s.r.o. Dvorská 605 563 01 Lanškroun IČO: 64793826 declare under own responsibility that the product: Electronic training collar Dogtrace d-control 500, 900 and 1500 mini is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EC meets requirements of General Licence of The Czech Telecommunication Office according to general licence no.
WARNING: The person with a personal instrument to support heart activity (pacemaker, defibrillator) must respect the relevant precautionary measures. The d–control emits a certain stationary magnetic field (lower part of the remote controller and RF signals). Frequency= 869,525 MHz, maximum transmitted power = 25 mW.
Introduction The electronic training collar Dogtrace d–control, consisting of the transmitter and the receiver, it is a modern, safe, reliable, and effective training tool. With the d-control training collar you can make corrections that are suited to your dog‘s temperament and the distraction level of the moment, at the proper time, for maximum training efficiency.
Battery insertion and replacement INSERTION (REPLACEMENT) OF THE BATTERY IN THE RECEIVER Unscrew the 4 screws of the top of the receiver using a cross-head screwdriver and remove the lid. Insert the lithium CR2 3V battery into the battery compartment. Please check that and the battery is installed with correct polarity (according to the polarity indicated with the "+"...
INSERTION (REPLACEMENT) OF THE BATTERY IN THE TRANSMITTER Remove the transmitter battery cover using a cross-head screwdriver. If replacing the battery, remove the old battery and dispose of it properly. Place the alkaline AA 1,5V batteries in the holder and press into place. Observe polarity when ...
Switching ON/OFF SWITCHING THE TRASNMITTER ON/OFF Switching on: Press down for 1 second the button on the transmitter. The LCD display indicates that the unit is active. Switching off: Again, press down for 1 second the button on the transmitter. ...
Programming (pairing) the transmitter with the receiver Each transmitter has its own operational code. The programming of the transmitter with the receiver enables the two units to work together. This operation will help you to program the receiver to work with a new transmitter or to program a new receiver to work with your existing transmitter.
Transmitter - button functions The Dogtrace d–control transmitters are designed to operate with two separate receivers (dog 1 and dog 2). The selected level of stimulations can be different for each receiver Button - Tone signal The receiver emits a beeping noise when a „Tone button“ is pressed. If the button is not released after 30 seconds, the tone will automatically turn off.
Page 11
Button -Booster Pressing the „Booster button“ enables you to use different levels of pre-set stimulation intensity at the transmitter. The stimulation is transmitted by the two contact points located on the receiver as long as the button is pushed. If the button is not released after 4 seconds, the stimulation will automatically turn off as a safety feature.
External remote control ONE TOUCH The electronic training collars d-control 510, 910 and 1510 mini are provided with the external remote control ONE TOUCH. It enables you to activate the pre-set stimulation (momentary or continuous) at the receiver by a quick pressing of one button.
FITTING THE COLLAR The receiver needs to be very snug around the dog‘s neck to work properly. A loose fit can allow the receiver to move around on the dog‘s neck. The collar must be just tight enough to allow the contact points to make good contact on your dog‘s skin.
Training tips The trainer’s elementary knowledge in dog training is the prerequisite for using the training collar. Do not hesitate to contact a professional trainer for any further advice. You can start using the collar with dogs of 6 months of age who has undergone the basic training ...
Do not use the electronic training collar for dogs under 6 months of age. Do not use the electronic training collar for pregnant or nursing bitches. Do not use the electronic training collar for dogs with health problems particularly heart disease, ...
Troubleshooting If your device seems to operate improperly, read this manual again, check the receiver battery and replace it if necessary. Try to initialize the receiver by removing the battery from the battery holder in the receiver, then use ...
Warranty Terms and Conditions VNT electronics Ltd. provides a 2-year warranty on the Dogtrace product with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: batteries ...
Page 19
5. We require that all items being sent for repair must be clean. Items deemed insufficiently clean will be returned to the customer unrepaired. Please do not include the strap or any other accessories if not subject to warranty. 6. Other rights and liabilities of the manufacturer and claimants are based on relevant general obligatory legal regulations of the country where the product was sold.