Electronic training collar –
basic training set for one dog.
electronic training collar –
basic training set for two dogs –
with a carrying case (20 pages)
Page 1
d–control 600, 1000, 1600 Electronic training collar d–control 602, 1002, 1602 Electronic training collar – a set for two dogs Service Instructions...
Page 2
Thank you for purchasing the product DOGtrace™ d–control from VNT electronics s.r.o., Czech Republic. We would like to ask you for reading this manual carefully before using the unit and keeping it for future use. EC Declaration of Conformity Guideline R&TTE 1999/5/CE The manufacturer: VNT electronics s.r.o.
Introduction Do you need to have your dog under instant control? Do you want to train and breed it easily, quickly, precisely, and effi ciently? Electronic training system DOGtrace™ d–control, consisting of the transmitter and the collar, will help you train your dog with effi ciency unat- tainable with other methods.
Battery installation and replacement INSTALLATION (REPLACEMENT) OF THE BATTERY IN THE RECEIVER (COLLAR) Remove 4 screws of the receiver housing cover plate with a cross-head screwdriver. Install the 3V lithium CR2 battery. Mind the correct polarity indicated on the receiver PCB with “+“...
Page 7
INSTALLATION (REPLACEMENT) OF THE BATTERY IN THE REMOTE CONTROLLER Open the battery compartment cover on the rear side of the remote controller and insert 2 AA size LR6 alkaline batteries. Mind the correct polarity indicated in the battery compartment. Replace the battery compartment cover and fi x with the screw. CAUTION: Rechargeable batteries can be used to operate your remote controller, however, they do not provide suffi...
Turning ON/OFF TURNING THE REMOTE CONTROLLER ON/OFF To turn on: Press down for 1 second the On/Off button on the remote controller. Turning on is indicated by lit LCD display. To turn off : Again, press down for 1 second the On/Off...
Programming (matching) of the remote controller and the receiver Every remote controller has its own RF operational code. Programming of the remote controller with the receiver (collar) will be accomplished during the fi rst use of the DOGtrace™ d–control or with a new remote controller or a receiver (when one or the other is lost).
REPROGRAMMING OF YOUR RECEIVER The receiver can be programmed repeatedly without restraint using the same remote controller or another (see the section Programming (matching) of your remote controller and receiver). It is possible to program an unlimited number of receivers to one receiver, which is possible for common training of several dogs.
Page 11
Or you can select a long pulse that will last as long as you keep pressing the button, however, it will be limited for 8 second at most. The red LED on the receiver will glow steadily. This will be indicated by the transmission symbol on the LCD. You can select a short pulse (option A) or a continuous one (option B) by pressing the button to select dog 1 repeatedly;...
How to check that your DOGtrace™ d–control works correctly You can check anytime whether your set works correctly. Before checking, make sure that the receiving collar is turned off . Connect the leads of the testing discharge lamp to both electrodes (loosen up the electrodes, insert the wires of the lamp under them so that they can be fi...
For the best results Training orders, you are sending to your dog, are transmitted from the transmitting unit to the collar equipped with the receiver by radio waves. The propagation of radio waves is infl uenced by a series of factors and under normal conditions the range of this unit is approximately 600–1600 metres (depending on geographic conditions and surroundings).
We are starting with the training collar The trainer’s elementary knowledge in training dogs is the prerequisite for using the training collar. If you do not have this knowledge, we recommend you to turn to a training centre, a cynology club, or a school for dogs where you will learn the basic communication with your dog.
Page 15
Sound signal It is only up to you how you will use it, which depends on the method you wish to train your dog. With the sound signal you can: Send a sound warning to your dog when it is doing something inappropriate. Catch the attention of your dog…...
Button – Booster You can use this button to set your remote controller. You can select a short pulse for the button and use it for long correction pulses you have preset, or you can set a higher level of the correction pulse than you have preset for the button and use it for resolving extreme situations when your dog did not respond to the default level of the correction pulse.
Hints for using Do not place your remote controller close to objects sensitive to magnetic fi elds that might get damaged and be out of repair. Do not put your d-control in places exposed to high temperatures. It is necessary to replace the batteries every two years and also in the case that the set is not used for a long time.
The remote controller is waterproof as much as possible. If it is dropped into water, it is likely that it will be irrecoverably damaged or destroyed. If you do not use the unit for a long time, remove the batteries from your remote controller and receiver.
Warranty DOGtrace™ provides the product with warranty for possible manufacture faults to the extent of two years from the date of purchase. The manufacturer does not take responsibility for damage to the instrument caused by incorrect use, unauthorized repairs and dismantling. The warranty does not cover the following items: Batteries New straps...
Technical data TRANSMITTER Weight ........175 grams (transmitter, battery) Range .
Page 21
Electronic invisible fence Do you have a wandering pet not paying attention to your protests who likes traveling nearby and far from your house? Or is it a garden lover who likes your garden patches or a swimmer who loves swimming in your pool? The d–fence is a modern Twisted...