Wm 08 Wireless Audio Module - Minelab EQUINOX 600 Instruction Manual

Contents
WM 08 Wireless Audio Module
The WM 08 receives wireless audio using advanced Wi-Stream technology to achieve
ultra-fast clear sound with no perceivable time delay.
The WM 08 has a 3.5 mm (1/8-inch) headphone socket. It can be
attached to your clothing using the wire clip. The WM 08 must be
paired to the EQUINOX before it can receive wireless audio.
Power Button
Connection
Status LED
3.5 mm (1/8-inch)
Headphone Socket
The WM 08 does not have a speaker so must be used with
headphones. To use with the ML 80 Wireless Headphones, connect
the auxiliary cable.
The WM 08 headphone socket is compatible with the EQUINOX
waterproof headphones, available as an accessory. Note that the
WM 08 itself is water resistant only and is not designed for use
underwater.
Attach the WM 08 to the same side of your body as the
detector to ensure the most reliable wireless signal.
When WM 08 is not in use, ensure that the plastic
dust-cap is screwed firmly into the headphone socket.
EQUINOX is not compatible with Minelab WM 10 and
WM 12 wireless audio modules.
Avoid having the WM 08 in close proximity to other
wireless electronic devices e.g. a smartphone
Pairing the WM 08
Pairing the WM 08 is only required at first time use, or when the
WM 08 has been paired to a different detector. EQUINOX will
automatically connect to the paired WM 08 for all future uses.
1. Press the WM 08 Power button for 2 seconds. The connection
LED will slowly flash blue.
2. Press the Pairing button on the WM 08 until the blue LED starts
flashing rapidly.
3. Press the Wireless button on the side of the EQUINOX control
panel for 2 seconds until the LCD wireless icon starts to flash
rapidly.
For first-time use of the EQUINOX, or following a factory reset, a
short press of the Wireless button will immediately start the pairing
sequence.
4. The blue LED on the WM 08, and the Wireless and Headphones
icons on the EQUINOX LCD will stop flashing and remain on
when the WM 08 has successfully paired.
If pairing is not successful within 15 seconds of initiating the
pairing sequence, return to step 1.
Unpairing a WM 08
Pairing Button
WM 08 audio modules can only be unpaired by pairing them to
another EQUINOX detector.
Pairing Additional WM 08 Modules
Battery Status LED
Up to 4 WM 08 audio modules can be in use simultaneously. This
is a useful feature for group training sessions. To pair additional
WM 08 audio modules, repeat the standard WM 08 pairing
procedure.
WM 08 Connectivity Icons
These icons appear on the top right of the EQUINOX LCD and show
the WM 08 connectivity status. The number of connected WM 08
modules is indicated below the Wireless icon:
Charging the WM 08
Going detecting with a fully charged WM 08 battery is
recommended. Typical battery runtime is
approximately 18 hours.
During operation, the WM 08 status LED will begin to flash red
when the battery requires charging.
1. Plug the supplied charging cable into any standard powered
USB-A port.
2. Connect the magnetic end of the charging cable to the WM 08
charging interface on the back of the module.
3. The LED will flash green whilst the unit is charging and remain
on when the unit is fully charged.
The charge time from completely flat to 100% is approximately 3
hours when a high capacity (>1.7A @ 5V) charger is used.
Connecting a Power Bank
Connecting the WM 08 to a power bank will allow you to continue
to use it even if the battery is low/flat. The power bank will charge
the WM 08, which will continue operating as normal.
WM 08 Wireless Audio Module | 55
1 device connected
2 devices connected
3 devices connected
4 devices connected