Dmx State; Dimmer Curve - ADJ 6-PACK SKB CASE User Instructions

Element HexIP Pearl
Power Supply:
The ADJ Element HexIP Pearl contains an automatic
voltage switch, which will auto sense the voltage when it is plugged
into the power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
Element HexIP Pearl
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. To
control this unit in DMX mode, your contoller must be connected
to a Wifly TranCeiver. This is a Wifly unit only. The Element HexIP
Pearl has 5 DMX modes: 6 channel mode, 7 channel mode, 8 channel
mode, 11 channel mode, and 12 channel mode. See page's 12-21 for
each mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed DMX
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 6 Channel Mode, press the MODE button until "Ch06"
is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until "Ch07"
is displayed. This is the 7 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until "Ch08"
is displayed. This is the 8 Channel DMX Mode.
• To run the 11 Channel Mode, press the MODE button until
"Ch011" is displayed. This is the 11 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until
"Ch012" is displayed. This is the 12 Channel DMX Mode.
4. Please see pages 12-21 for DMX values and traits.
ADJ Products, LLC - www.adj.com - Element HexIP Pearl User Manual Page 11
Set Up
Element HexIP Pearl

DMX State:

This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
DMX Control
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. "XXX" represents the current displayed DMX address.
2. Press the SET UP button so that "nodn" is displayed. Use the UP
and DOWN buttons to scroll through the DMX states.
• "bLAC" (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• "LASt" (Last State) - If the DMX signal is lost or interrupted,
the fixture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.
• "ProG" (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. After you have found your desired setting, press SET UP to exit.

Dimmer Curve:

This is used to set the dimming curve used with DMX mode. See
page 33 for the dimming curves chart.
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. "XXX" represents the current displayed DMX address.
2. Press the SET UP button until "dr-X" is displayed. "X" represents
the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your
desired dimming curve.
ADJ Products, LLC - www.adj.com - Element HexIP Pearl User Manual Page 28
Operating Instructions