Setup Requirements - Angelcare AC315 Owner's Manual

must not be collocated or operating in conjunction with any other antenna
or transmitter.
15.17 Power Lines - An outside antenna system should NOT be located
in the vicinity of overhead power lines or other electric light or power
circuit, or where it can fall into such power lines or circuits as contact
with them may be fatal.
15.18 Vibration Source - When the monitor is in use, DO NOT use a bedside
crib, cot mobile or other cot accessories that may produce vibrations. Other
sources of vibrations may include fans, washing machines, loud music, etc.
These sources of vibration may interfere with the performance of your
Angelcare ® monitor and the alarm will not sound if it continues to detect
any movement other than your baby's. Be sure all vibration sources are
eliminated before using the monitor.
15.19 You may experience false alarms for several reasons . The
most common reason is the C amera has not been turned OFF
after you have removed your baby from the cot. Another reason is
the Sensor Pad has not been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm surface with the Angelcare
side facing up. The sensitivity level may also need to be adjusted. Refer
to Step 5.1. Always be sure to immediately check on baby whenever an
alarm sounds.
15.20 Sensor Pad - Your Sensor Pad can be used in any cot that is stationary.
If the cot has a spring or slat base, place a hard board between the cot base
and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick. Only
use your Angelcare ® monitor in a stationary sleeping environment such
as a cot where the Sensor Pad can rest on a completely flat, firm surface.
The Sensor Pad is made of plastic and does not permit the air to circulate.
Therefore, mildew build up could develop underneath the mattress in the Sensor
Pad area. We suggest rotating the mattress regularly to prevent any mildew.
16. IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES
16.1 Use ONLY the type and size of battery specified in the owner's manual.
There is a risk of explosion if battery is replaced with an incorrect type.

SETUP REQUIREMENTS

INCLUDED:
Touch control Parent Unit
Wired movement
Sensor Pad
* Always place
Angelcare logo side up *
01m5_Manuel_AC315_UK_12703.indd 3
16.2 Charge the battery for 9 hours prior to first use. Be sure to have the
monitor in the OFF position during this period. ONLY use the adapters
included with your monitor.
16.3 DO NOT use these adapters with any other equipments.
16.4 When unplugging the adapter from the Camera, be sure it is switched
to the OFF position.
16.5 DO NOT dispose of batteries in fire. They may explode. Check with
local regulations for possible special disposal instructions.
16.6 Exercise care in handling batteries in order not to short out the
batteries with conducting materials such as rings, bracelets and keys.
Overcharging, short circuiting, reverse charging, mutilation, or incineration
of batteries must be avoided to prevent one or more of the following
occurrences: release of toxic materials, release of hydrogen and/or oxygen,
gas and rise in surface temperature.
16.7 DO NOT attempt to rejuvenate the battery provided with or identified
® logo for use with this product by heating them. Sudden release of battery
electrolyte may occur, causing burns or irritation to eyes or skin.
16.8 If and when necessary, the battery must be replaced with identical
new ones or equivalent (volts and size).
16.9 Remove the battery from the Parent Unit if you store the product
over 30 days because the battery could leak and damage the product.
16.10 Discard 'dead' batteries as soon as possible since 'dead' batteries
are more likely to leak in a product. If a battery has leaked or vented, it
should be replaced immediately using protective gloves.
16.11 DO NOT store this product, or the battery provided with or identified
for use with this product, in high-temperature areas.
Tabletop stand with
removable wall
mount metal ball
Camera (for Camera)
AC adapter
(for Parent Unit)
(for Parent Unit)
6 Pre-threaded cord covers with
Split USB cable
Model AC315
Baby Video, Sound and
Movement Monitor
Hardware
(Screwdriver
required
for wall mounting)
Lithium ion AC adapter
battery pack (for Camera)
2017-10-16 9:19 AM
E
N
3