(CUCM, VCS); the pages shown in grey color are not available if the video system is registered to the Cisco cloud service (Cisco Spark). In both cases, a user that is signed in, sees only the pages that he has access rights for.
You can customize our touch user interfaces to include input sources that are connected to a third-party external video switch. You need a Cisco video system with a touch interface, a third- The sources will appear and behave as any other video source party control system, for example Crestron or AMX, and a third- that is connected directly to the video system.
This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera. does not provide satisfactory results. Requires the Cameras Camera [n] Gamma Mode to be If adjusting the camera position by hand you can configure whether the camera should keep set to Manual.
Auto option in the configuration. All Cisco Precision cameras support both anti-flickering and auto detection of line frequency. Auto is the default value, so you should change this setting if you have a camera that does not support auto detection.
(Cisco Unified Communications Manager (CUCM) version Default value: Off 9.1.2 or newer, Cisco TelePresence Video Communication Server (VCS) version X8.1 or newer, Cisco Media Server (CMS) version 2.1 or newer). Change this setting if you want to Value space: Off/On disable the active control features.
If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the system cannot register, the auto-selection chooses H323. Value space: Off/On/BestEffort H320: All calls are set up as H.320 calls (only applicable if connected to Cisco Off: The system will not use encryption. TelePresence ISDN Link).
Allow: You will be notified when someone calls you while you are already in a call. can use its own built-in MultiSite feature. If registered to a Cisco Unified Communications You can accept the incoming call or not. The ongoing call may be put on hold while Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM...
Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN Define the static IPv4 network address for the system. Applicable only when Network IPv4 clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Assignment is set to Static.
Default value: Auto Value space: Auto/Manual/Off Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled. Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.
Default value: Off The HTTP Proxy Settings are available from the user interface when the system is provisioned to Cisco Spark. The HTTP proxy settings makes it possible to onboard a video Value space: Off/On system behind a HTTP proxy to Spark.
NetworkServices HTTP Proxy Mode NetworkServices HTTPS StrictTransportSecurity The HTTP proxy for Cisco Spark can be set up manually or turned off. The HTTP Strict Transport Security header lets a web site inform the browser that it should never load the site using HTTP and should automatically convert all attempts to access the Requires user role: ADMIN, USER site using HTTP to HTTPS requests instead.
SNMP Agent in the codec. The default Requires user role: ADMIN password is "public". If you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP Community is configured there too. NOTE: The SNMP Default value: On Community password is case sensitive.
Peripherals Pairing CiscoTouchPanels RemotePairing In order to use Cisco Touch 10 (touch controller) as user interface for the video system, Peripherals Profile ControlSystems Touch 10 must be paired to the video system via the network (LAN). This is referred to as remote pairing.
Appendices Peripherals Profile TouchPanels Define the number of Cisco Touch controllers that are expected to be connected to the video system. This information is used by the video system's diagnostics service. If the number of connected Touch controllers does not match this setting, the diagnostics service will report it as an inconsistency.
CUCM: The phonebook is located on the Cisco Unified Communications Manager. Spark: The phonebook is located on Spark. TMS: The phonebook is located on the Cisco TelePresence Management Suite server. VCS: The phonebook is located on the Cisco TelePresence Video Communication Server.
Spark: Push configurations to the video system from Spark. TMS: Push configurations to the video system from TMS (Cisco TelePresence Management System). VCS: Push configurations to the video system from VCS (Cisco TelePresence Video Communication Server). Provisioning LoginName This is the username part of the credentials used to authenticate the video system with the provisioning server.
This is the password part of the credentials used to authenticate the video system with the Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager provisioning server. This setting must be used when required by the provisioning server.
In order to use a client, at least one of the Proximity services must be must be On for this setting to take any effect. enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the Proximity services.
ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be video systems can use to discover the optimized media path. Thus the shortest route for part of a shared line.
Default value: "" Value space: Standard/Cisco Value space: String (0, 255) Standard: Use this when registering to standard SIP Proxy (tested with Cisco The preferred format is DNS SRV record (e.g. _turn._udp.<domain>), or it can be a valid TelePresence VCS).
You can customize the user interface to allow control of peripherals in a meeting room, for example lights and blinds, or to You need a Cisco video system with a Touch 10 controller, and a modify the video system’s behavior by triggering macros.
All images in these materials are for representational purposes only, actual products may differ. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.
Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/ or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.